PROVN OF SOLID WASTE MAGAGEMENT IN BAISAKHI MIL STN UNDER GE 859 EWS; 1 S&F of Glass bottle crusher capable to crush bottles, jrs, vases etc with twin shaft mechanism may shreading 400-500 kgs/hr of 3 phase 415 volt fitted with 7.5 HP motor with online starter complete with 3 phase 415 voltswith all fittings all starter automatic switching off of blades during opening of hooper doors complete. The machine will be installed at cold climatic conditioned, having temprature range of minus ten (-10 to +15) to plus fifteen degree, designing of the mechine will be capable to function in the above specified temprature.Note :The rate quoted shall be deemed to include for carry out one month on job training to the personnel detaiied by User. 2 S&F fully automatic Organic Waste Compositing Machine of 500 Kg Capacity with built in Shedder of 415 volt 50 Hz overload protection , heater inbuilt, power saving mode automatic switching off of blades during opening of hooper doors fully automatic including power of motor 10.35 KWincluding separate door for putting waste and removing waste made with Stainless steel outer body , steel shaft & mixing blades, shreadder made with High carbon steel and shreadder motor capacity 2 HP having shredder capacity range of 150 to 200 kg per hour complete all as specified and directed. The machine will be installed at cold climatic conditioned, having temprature range of minus ten (-10 to +15) to plus fifteen degree, designing of the mechine will be capable to function in the above specified temprature.Note :The rate quoted shall be deemed to include for carry out one month on job training to the personnel detaiied by User. 3 S&F of manual plastic bale press machine suitable for very compact bailing ofwoven sack waste, paper waste, pet bottle waste of hydraulic bailing technology having 5 ton per day capacity 3 phase 415 volt fitted with 5 HP motor with online starter complete with 3 phase 415 voltswith all fittings all starter automatic switching off of blades during opening of hooper doors complete. The machine will be installed at cold climatic conditioned, having temprature range of minus ten (-10 to +15) to plus fifteen degree, designing of the mechine will be capable to function in the above specified temprature.Note :The rate quoted shall be deemed to include for carry out one month on job training to the personnel detaiied by User. 4 Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100V grade with stranded aluminium conductor of size 70 sqmm 3.5 core including taking down of old unserviceable UG cable/service wires.Make :- Havells/KEI/Polycab 5 Description all as per item No 1 above but of size 16 Sqmm 4 core 6 M&L of SPN type rewireable switch fuse unit of 230 Volt 50 Hz three phase three pole of capacity 63 Amp including MS box with backelite fuse & fuse carrier fittings , operating insulated handle, top cover necessary locking arrangemnts etc as per IS/IEC 60947 1&3 including necessary wall mounting fittingduly grouted/fixed in PVC Board or on wooden board as directed 7 Supply and laying Double wall corrugated HDPE duct pipe 80mm outer dia confirming to IS: 14930 (Part-II) of approved colour with fittings for cable protection complete laid in trenches or fixed on walls with clamps of suitable size all as specified and directed by Engineer-in-charge. 8 M&L for earthingcomplete with galvanised steel earth plate electrode 60x60cmx6 mm thick burried directly in ground ( earth pit not less than 2.25 Mtr deep below ground level ) with top edge of the plate not less than 1.5 Mtr below normal ground level, connected to galvanised iron strip 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel all as shown in electrical plate No. 3 of SSR Part-I 2009 connected all as specified 9 S&F & testing commissioning of outdoor type Feeder panel pedestal type weather proof CPRI approved MS cubical panelboard outdoor type, 4 Nos ofbus bar of 300 Amp capacity & MCCB 160 Amp capacity 4 pole (Ics = Icu = 100%) and 03 X outgoing MCCB 63 Amp each including one coat of red oxide and two coat of enamel paint powder coated, mounted on channels and PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) in foundation for fixing panels aluminium busbar chanel insulated with colour coated heat shrinkable sleaves and mounted on DMC/Epoxy insulator all as specified & directed. 10 Excavationin trenches in any type of soil not exc 1.5 mtrs wide and not exc 1.5 mtr in depth for laying of pipe/ cables/ poles etc and getting out hard & densile soil complete all as specified and as directed. 11 Surface excavation n.exc 30 cm deep & averaging 15 cm deep and getting out in hard/dense soil. 12 Returning fitting in any type of soil including spreading leveling watering and well ramming in layers n.exc 25 cm complete all as specified and as directed. 13 Removing excavated soils to a distance n.exc. 50 mtr and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed. 14 M&L for cement concrete type D-2, 1:4:8in Cement concretein foundations, filling and mass concrete. 15 M&L For Hard core, broken to gauge n exc 63 mm for stone boulder/boulder completed all as soecified. 16 M&L for PCC 75mm thick, type D-2, 1:4:8 (using 40mm graded stone agg) in sub-floors, sub-base, floors and pavings etc. 17 M&L for100 mm PCC 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass concrete 18 M&L for plain cement concrete 75mm thick type C-2, 1:3:6, (40mm graded stone aggregate) as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement. 19 M & L for screed bed or bedding layer of15 mm thick for laying floor finishes in CM (1:6 ). 20 M&L for joint free Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical surfaces etcset and jointed in neat cement slurry and pointed in white/coloured cement to match the shade . (Make; Kajaria/ Orient Bell/ Johnson/ Somany).Note :- Colour and pattern will be decided by GE/Engr-in-charge. Contractor will bought the tiles only after approval ofcolour and pattern of tile by GE/Engr-in-charge. 21 M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete. 22 M&L rendering 10mm thick in CM 1:4on concrete inner surfaces finished even and smooth without using extra cement . 23 M&L for Prepairing surfaces plastered or unplastered newly surfaces with two coats of cement base paint over one coat of white wash as completed. 24 S&F Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed. 25 S&F 30mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats. 26 S&F 30mm thick 2nd class hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, woodparticle board with commercialface veneers: supplied and fitted to chowkats. 27 S&F 100 mm size Butt hinges, medium weight, cold rolled mild steel, and fixed. 28 S&F 150 mm longaluminium anodized, barrel tower bolts extruded section. 29 S&F 125 mm longaluminium anodized, barrel tower bolts extruded section. 30 S&F 125 mm size extruded aluminium alloy handles, fabricated type, anodised. handle fabricated type. 31 S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. 32 M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 33 S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified . 34 S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge, hips fixed with self tapping screws as specified . 35 M&L for preparation of newly steel surface of any description, over 10cm in width or girth,not otherwise described applying two coats of synthetic enamel paint over one coat of red oxide primer.
