|
| 1 | Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap) 500 mm dia piles (20.0 m length) |
| 2 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 3 | Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.Single pile upto 50 tonne Safe capacityInitial test (Test Load 2.5 times the Safe capacity) |
| 4 | Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.Single pile upto 50 tonne Safe capacityRoutine test (Test Load 1.5 times the Safe capacity) |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 6 | Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling withapproved material.V) In marshy soili) upto 3 m depthB) Mechanical Means(ii) With dewatering |
| 7 | Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803,1202 & 1203P.C.C Grade M20Nominal mix (1:2:4) |
| 8 | Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.I. Without PlasticiserC. RCC Grade M20 (Case I) Using concrete mixer |
| 9 | Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301. |
| 10 | Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size toeards the wall and provided over the entire surfaces behind the abutement, wing wall and return wall to the full height compacted to firm condition complete as per drawing and technical specification. |
| 11 | Providing and laying of apron with cement concrete blocks of size as per Table 1300.1 cast-in-situ and made with nominal mix of M-15 grade cement concrete as per drawing and technical specifications Clause 1301. |
| 12 | Construction of whole bamboo single palisading with matured Bhaluka bamboo posts 7.5 cm to 10 cm dia., 15 cm clear apart 1.50 m to 1.80 m above ground and 1.00 m to 1.20 m below ground with Bhaluka bamboo inclined struts placed at 1.5 m a part tied with three rows of horizontal half Jati bamboo kamies etc.complete as directed. (Using Bhaluka Bamboo at the rate of 10.14 nos./Rm & Jati Bamboo at the rate of 2.40 nos./Rm) |
| 13 | Serviceable empty cement bags. |
| 14 | Labour charge for filling of empty cement bags to attain minimum filled up volume of 0.028 Cum with filled up size of 0.7 m × 0.40 m × 0.10 m, laying and pitching of the earth filled cement bags including excavation and borrowing earth, breaking clods, filling in bags and supplying and stitching the mouth with jute sutli, etc. complete as directed. (Cement bags will be supplied by the department free of cost). For borrowing earthfrom a distance beyond 30m. & up to 60m. For borrowing earth from a distance beyond 30 m. &up to 60 m. |
| 15 | Ordinary / unskilled labour. |
| 16 | Dewatering by 5 H.P. water pump including supply of necessary fuel, engine oil and pump operator etc complete.For 3 Nos@ 1.5% of Civil Works |
| 17 | Supplying and fixingsteel sluice gate shutter. for5 Nos |
| 18 | Medium Jungles: Clearing medium jungles and trees upto 15 cm. girth including cutting, uprooting roots and stumps, removing them from the site of the work, etc. complete as directed. ( When 30%to 60 % of the area is covered by shrubs,trees etc) |
| 19 | Cutting bamboo, uprooting roots & stumps including removing them from the site of work, etc. complete as directed. |
| 20 | Uprooting bamboo clumps where bamboo already removed including removing stumps to a minimum distance of 30 m etc., complete as directed. |
| 21 | Construction of temporrary shed of two roof with mud plinth of 0.45 m height above ground level with Bhaluka bamboo post 1.5 m apart driven at atleast 0.75 m below groundand height above plint 2.5m. Split Jatti bamboo wall mud plastering white washing 2 coats, 10 cm thick touch roofing over bamboo rua frame placing at 0.15 m clear apart fitted with bamboo kamies from binding doors and windows with Bamboo Chattai strengthening with Bamboo frame binding with wire etc compple as directed. (Using Bhaluka Bamboo at the rate of 6.00 nos/ Rm & Jati Bamboo at the rateof 61.00nos / Rm) 7 nos at seven different location. |
| 22 | Manufacturing, supplying and fixing retro reflective sign boards of size 1.22m X 0.76 m made up of 4 mm thick aluminium sheet,face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC: 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 nos of900 mm thick pipe vertical post (AISI 202 Grade) of length 3750 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 30cmx30cmx30cm etc.complete. and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical post to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-Charge. |
| 23 | Supply of Geo-textile bags of type-A (1.03 × 0.70M) inner to inner made of Geo-textile non-woven fabric sheets of 400 GSM manufactured from 100% virgin Polypropylene (PP) fibre with minimum properties as per IS 16653 : 2017(i) Wide Tensile strength(MD) ≥20KN/m & Wide Tensile strength(CD) ≥20 KN/m (ii) Elongation (MD) ≥50% & Elongation (CD) ≥50%(iii) Abrasion ≥95% (iv)Trapezoidal Tear Strength (MD) ≥450N & Trapezoidal Tear Strength (CD) ≥450N (v)CBR Puncture strength≥4000N (vi)Permittivity≥1.10s-1 (vii)Permeability≥40l/m2/sec (viii)AOS ≤75micron(ix) UV Resistance @500 hours retained Tensile strength (MD) & (CD) ≥ 80% (x)Mass≥400 gm/m² (xi) Thickness at 2 KPa≥3 mm (xii) Seam strength ≥80 % of actual fabric strength. Stitching of Bags should be Ring Spun Yarn stitches with 2500-3000 denier double line chain stitch with overlap with stitches along the edge @ minimum 15 stitches per 100mm. (Bags are to be supplied of 100 numbers in a bundle, properly packed with each bag having proper tag with name of Manufacturer, Batch Number, the GSM and type of polymer encrypted and stitched on top corner and each bag is to be marked with “WRD Govt of ASSAM” to be printed distinctly. Test Certificate from approved NABL accredited and ISO (Certified Laboratory should invariably be submitted against each batch of material) |
| 24 | Carriage of Geo Bags of size 1.03 x 0.70 m/1.0 x 0.7 m including loading & unloading, Stacking, etc. complete and including hire charge of truck with driver and handyman cost of POL etc. completed as directed. (distance to be calculated from Divisional Store)Distance= 30 Km |
| 25 | Supply of Geo Bags Type-B (Size 2.00m × 1.50m inner to inner) (Pillow Type) made of composite layers of Polypropylene (PP) fibre as per IS 16653 : 2017 for Nonwoven and IS 16654 : 2017 for Woven: Woven Geo-textile for the outer cover (300gsm): The woven geo textile is woven with multifilament woven fabric manufactured from ultra violet stabilized polypropylene. Geo-textile used to manufacture geotextile bags should have high mechanical properties for enhanced durability along with enhanced puncture, abrasion and U.V. resistance characteristics. Geo-textile should be inert to biological degradation and resistant to naturally encountered chemicals, alkalis, and acids.Properties(i) Tensile strength (MD) ≥80 KN/m & Tensile strength (CD) ≥70 KN/m (ii) Elongation (MD) ≤25% & Elongation (CD) ≤25% (iii) Abrasion ≥75% (iv) Trapezoidal Tear Strength (MD) ≥1500N & Trapezoidal Tear Strength (CD) ≥1300N(v) CBR Puncture strength ≥900N (vi) Permeability ≥18 l/m2/sec (vii) AOS ≤250 micron (viii) UV Resistance @500 hours retained Tensile strength (MD) & (CD) ≥80% (ix) Mass ≥300 gm/m² (x) Seam strength ≥50 % of actual fabric strength.Non-Woven Geo-textile for the inner layer (300gsm): It is needle punched non-woven geo-textile made of 100% polypropylene staple fibres which are formed into a random Trapezoidal Tear Strength (CD) ≥340 N (v) CBR Puncture strength ≥3000 N(vi) Permittivity ≥1.25 s-1 (vii) Permeability ≥60 l/m2/sec (viii) AOS ≤75 micron (ix) UV Resistance @ 500 hours retained Tensile strength (MD) & (CD) ≥80%(x) Mass ≥300 gm/m² (xi) Thickness at 2 KPa ≥3 mm (xii) Seam strength ≥80 % of actual fabric strength.Stitching of Bags should be Ring Spun Yarn stitches with 2500-3000 denier double line chain stitch with overlap with stitches along the edge. (Bags are to be supplied of 15 numbers in a bundle, properly packed with each bag having proper tag with name of Manufacturer, Batch Number, the GSM and type of polymer encrypted and stitched on top corner and each bag is to be marked with “WRD Govt of ASSAM” to be printed distinctly. Test Certificate from approved NABL accredited and ISO Certified Laboratoryshould invariably be submitted against each batch of material) |
| 26 | Carriage of Geo Bags of size 2.00 x 1.50 m including loading & unloading , Stacking cost of P.O.L. ,etc. complete and including hire charge of truck with driver and handyman, etc. completed as directed.(distance to be calculated from Divisional Store)Distance= 30 Km |
| 27 | Filling and laying of Geo bags of size 1.03m X 0.70m including excavation of sand/silt of size more than 80 micron from flood plain or adjacent chars within a distance of 90m of the work site, filling geo bags with sand/silt having minimum weighing 126.00 Kg and minimum volume 0.084 Cum after filling ,double locking chain stitching the mouth of the filled bags with polypropylene thread by power driven double needle double stitched machine, stacking the same in batches of 100, carrying the same to the dumping site including all handling charges and local carriage within a distance of 150m and laying properly as directed. (Geo Bag and Polypropylene thread will be supplied by the department free of cost)With Engine Boat |
| 28 | Filling and laying of nonwoven Geo-textile bag of dimension 2.00mx1.50m including excavation of sand/silt from flood plain or adjacent chars within a distance of 90m of the work site, filling geo bags with sand/silt, having minimum volume 0.612 Cum after filling, double locking chain stitching the mouth of the filled bags with polypropylene thread by power driven double needle machine, laying at proper site including allhandling charges and local carriage within a distance of 100m complete as directed. (Geo Bag and Polypropylene thread will be supplied by the department free of cost)With Engine Boat |
| 29 | Supply of Sewing Thread/Yarn PPMF Stitching Thread (2000 Den. Kaplon) |
