|
| 1 | Part A- Repair of 125 HP submersible pump, ATS, Capacitor, Blower, flash mixer, Alum, TCL Agitator Water Treatment Plant. Item No.1 :- Removing of under repairdamaged 250mm dia Submersible Pump set of 125 HP/5 Stage from Fiter Sump. |
| 2 | Item No.2 :- Rewinding of 125 HP submersible motor with material and Labour charges. |
| 3 | Item No.3 :- Removing of old damaged motor G.M. bush and fitting of new motor G.M. bush and Labour charges. |
| 4 | Item No.4 :-Replacement and fitting of Lower /Upper Thurst Bearing Set. |
| 5 | Item No.5 :-Replacement and fitting of Motor Stud ring. |
| 6 | Item No.6 :-Replacement and fitting of Stage casing (C.I) with labour charges. |
| 7 | Item No.7 :-Replacement and fitting of pump stage neckring with labour charges. |
| 8 | Item No.8 :-Replacement and fitting of pump S.S.Sleeve with Labour charges. |
| 9 | Item No.9 :-Replacement and fitting of Pump G.M. Bush with Labour charges. |
| 10 | Item No.10 :- A) Flat flexible submersible cable wire.Providing and errecting flat flexible submersible cable with, copper conductor, 3 core, 16.00 sqmm, pvc insulated & pvc sheathed cable wire.(MJP Mech CSR 2023-24 Section 12 LT Cable item no CB-1-7 p no.48) |
| 11 | B) Flat flexible submersible cable wire.Providing and errecting flat flexible submersible cable with, copper conductor3 core, 25.00 sqmm For 125HP Sub.Pump |
| 12 | Item No.11 :- Errecting of repairedSub Motor & Pump of 125 HP/5 Stage at site with test & trail. |
| 13 | Item No. 12:- ATS Transformer 125 HP :-Rewindind of ATS Tramsformer 125 HP with Auto transformer oil and Labour charges. |
| 14 | Item No. 13:- Repair of ATS Starter 125HP :-. Supplying and replacing contactor for star-delta motor starter suitable for 100 HP to 125 HP. (PWDCSR 2023-24 item no 18-3-30p no.272) |
| 15 | Item No.14:- Capacitor providing & errecting bank of metalised polypropylene condensers with standard capacities of 1,2, 3, 5, 7, 10, 12,15,20 & 25 kVAr units of P.F. correction for operation on 3 phase 50 Hz. 500volt + or - 10% externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and provided with terminal cover box complete erected and tested.( MJP Mech CSR 2023-24 p no 36/section- 9 cp-1 ) |
| 16 | Item No - 15 :- Providing & erecting 4 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-MCCB(PWD CSR 2023-24 item no 5-5-3 & note no.1 p no.79) |
| 17 | Item No.16 :- Flat flexible submersible cable wire. Providing and errecting flat flexible submersible cable with, copper conductor, 3 core, 2.5 sqmm, pvc insulated & pvc sheathed cable wire.(PWD CSR 2023-24 item no 12-4-8 p no.175) |
| 18 | Item No.17 :- Supplying & erecting crimping type aluminium lugs for cable 300 sqmm complete as per specification No. CB-CL/AL(PWD CSR 2023-24 item no 7-10-11 p no.125) |
| 19 | Item No.18 :- Repairing of Wash Water Motor10HP Submersible pump. 30 village filter Remove from source,dismentaling of motor ,remove burnt winding wire from stator ,replacement of worn out GMbush (motor and pump) , thrust bearing & rewinding of sub motor with new winding wire as HP gauge & fitting of new GMbush, thrust bearing along with transportation ,installation & testing at sitelocation etc comp (As per MJP/PWD CSR/Z.P. Approved Rate) |
| 20 | Item No.19 :- Repairing of Flash mixer with gear box ,motor,panel etc. servicing with material and Labour charges. |
| 21 | Item No.20 :- Repairing of clarifier bridge with gear box ,motor etc.welding,grinding, servicing with material and Labour charges. |
| 22 | Item No.21 :- Repairing of filter media, M S gate,MS pipe welding with gear box ,motor etc. servicing with material and Labour charges. |
| 23 | Item No.22 :- Repairing of flocculator gear box , motor,flocculator ,MS Shaft etc. servicing with material and Labour charges. |
| 24 | Item No.23 :- Repairing of Alum,TCL Agitator with gear box & motor,panel wiring etc.with material and Labour charges. |
| 25 | Item No.24 :- Repairing of Air blower 15HP,TEFC motor,blower,starter servicing with material and Labour charges. |
| 26 | Item No.25 :-Supplying of grease. |
| 27 | Item No.26 :-Supplying and topping up new insulating oil for transformer conforming to IS 335 :1993 of approved make with test certificate.(PWD CSR 2023-24 item no 18-3-2 p no.271) |
| 28 | Item No.27 :-Supplying of bearing oil,blower oil. |
| 29 | Item No.28 :-Supplying of Joint Rope 16mm size |
| 30 | Item No.29 :-Providing, fabricating, erecting, M.S. Flanges sleep on type (all tables) of required size and thickness with both side machined. M S Pipe,Angle,channel iorn work etc. (MJP Mech CSR 2023-24 Section- 4 item no PW-10-1 p no.18) |
| 31 | Item No.30 :- Transportation charges for materialfrom site filter to workshop & workshop to filter. |
| 32 | At-Pure water Sump At Killari Item No.31- Repairing of Motor 10 HP Remove from source,dismentaling of motor ,remove burnt winding wire from stator ,replacement of worn out GMbush (motor and pump) , thrust bearing & rewinding of sub motor with new winding wire as HP gauge & fitting of new GMbush, thrust bearing along with transportation ,installation & testing at sitelocation etc comp (As per MJP/PWD CSR/Z.P. Approved Rate) |
| 33 | Item No.32- Repairing of Motor 25 HP Remove from source,dismentaling of motor ,remove burnt winding wire from stator ,replacement of worn out GMbush (motor and pump) , thrust bearing & rewinding of sub motor with new winding wire as HP gauge & fitting of new GMbush, thrust bearing along with transportation ,installation & testing at sitelocation etc comp (As per MJP/PWD CSR/Z.P. Approved Rate) |
| 34 | PART B- At -Repair of 180 HP V.T.pump,ATS,Capacitor Headworks, Makni Dam Item No.1 :- Removing of under repair damagedV T,VHS Motor set of 180 HP from Headworks. |
| 35 | Item No.2 :- Removing of under repair 180 HP VT motor ball assembly from foundation frame including Labour charges. |
| 36 | Item No.3 :- Rewinding of 180 HP V. T., VHS motor ball assembly with material and Labour charges. |
| 37 | Item No.4 :- Removing of wornout motor ball bearing and fitting of new motor ball bearing, bearing oil and Labour charges. |
| 38 | Item No.5 :- Removing of wornout motor ball bearing and fitting of new motor ball bearing, bearing oil and Labour charges. |
| 39 | Item No.6 :-Supplying of motor bearing oil. |
| 40 | Item No.7 :-Fitting of motor with labour charges. |
| 41 | Item No. 8:- Removing of ball Assembly from Foundation frame including Labour charges. |
| 42 | Item No.9 :- Removing of wornout ball Assembly G.M.Bush and fitting of new G.M.Bush including Labour charges. |
| 43 | Item No.10 :- Removing of wornout ball Assembly rubber bush and fitting of newrubber bush including Labour charges. |
| 44 | Item No.11 :- Removing of wornout ball Assembly upper G.M.bush and fitting of new upper G.M.bush including Labour charges. |
| 45 | Item No.12 :- Removing of wornout ball Assembly lower G.M.bush and fitting of new lower G.M.bush including Labour charges. |
| 46 | Item No.13 :- Removing of wornout column pipe spider rubber bush and fitting of new column pipe spider rubber bush including Labour charges. |
| 47 | Item No.14 :- Removing of wornout line shaft sleeve of column pipe spider rubber bush and fitting of new line shaft sleeve of column pipe spider rubber bush including Labour charges. |
| 48 | Item No.15 :- Removing of wornout T.T.Plate G.M.Bush and fitting of newT.T.Plate G.M.Bush including Labour charges. |
| 49 | Item No.16 :- Removing of wornout high light packing and fitting of new high light packingincluding Labour charges. |
| 50 | Item No.17 :- Balancing of line shaft and giving test & trial on site including Labour charges. |
| 51 | Item No.18 :- Neckring of 180HP ball assembly impeller with Labour charges. |
| 52 | Item No.19 :- Removing of wornout Suction strainer and fitting of new Suction strainer including Labour charges. |
| 53 | Item No.20 :- Removing of wornout nut & bolt for column pipe & pump & installing new nut & bolt for column pipe including Labour charges. |
| 54 | Item No.21 :- Colouring of 180HP V T Pump column pipe including Labour charges. |
| 55 | Item No.22 :- Errecting of repairedVT Pump of 180 HP at site with test & trail. |
| 56 | Item No. 23:- ATS Transformer 180 HP :-.Rewindind of ATS Transformer,repair of ampere, voltmeter,timer,no & nc Switch,control wiring with material and Labour charges. |
| 57 | Item No. 24:- 180 HP Main Panel :- Repair of SFU,HRC Fuse,Ampere,voltmeter, indicator for panel wiring Bus Bar,insulator etc. with material and Labour charges. |
| 58 | Item No.25:- Capacitor providing & errecting bank of metalised polypropylene condensers with standard capacities of 1,2, 3, 5, 7, 10, 12,15,20 & 25 kVAr units of P.F. correction for operation on 3 phase 50 Hz. 500volt + or - 10% externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and provided with terminal cover box complete erected and tested.( MJP Mech CSR 2023-24 p no 36/section- 9 cp-1 ) |
| 59 | Item No 26 :- Providing & erecting 4 Pole MCCB, 415V, up to 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixedmagnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCBwith phase barriers on both sides,insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-MCCB.For Capacitor (PWD CSR 2023-24 item no 5-5-3 & note no.1 p no.79) |
| 60 | Item No.27 :- Flat flexible submersible cable wire.Providing and errecting flat flexible submersible cable with, copper conductor, 3 core, 16.00 sqmm, pvc insulated & pvc sheathed cable wire.(MJP Mech CSR 2023-24 Section 12 LT Cable item no CB-1-7 p no.48) For Capacitor |
| 61 | 18% GST |
