|
| 1 | Dismantling structural steel work including doors, gates but excluding framed truss etc |
| 2 | S&F portions framed & hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165 |
| 3 | M&L for preparation of new or previously untreated steel or iron surfaces of any description over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 4 | M&L for cement concrete type B1 1:2:4 (using 20mm graded stone aggregates) in precast cover slabs for manholes cover and similar articles with plain faces etc set in cement mortar 1:4 including use and waste of formwork and including demoiltion of precast cover slab for manholes complete all as specified and as directed. |
| 5 | M&L for TMT bar 8mm dia and over cut to length bent to shape reqd incl cranking bending etc complete & binding with MS wire (annealed) not less than 0.9mm dia in reinforcement complete all as specified and as directed. |
| 6 | Providing 25 mm thick (measured solid) precast cement concrete louvres and jallies,Type B-0, 1:2:4 (using 12.5mm gradedaggregate) settingin CM 1:6, , including all mould- ings complete all as specified and as directed. |
| 7 | Demolition ofCement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) un-reinforced cleaning the premises and removal of rubbish out side the MD land at the location notifiedby the municipal authorities complete all as specified and as directed. |
| 8 | M&L for precast concrete solid block masonry exc 10cm width with solid block of PCC (1:5:8) Gde D-5 and setting in CM 1:6 and including demolition of brick work / Stone masonary / PCC block masonary built in cement morter of any description and removing of rubbish Out side MD land notifiedby the municipal authorities complete all as specified and as directed. |
| 9 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises outside MD land as notifiedby the municipal authorities complete all as specified and as directed. |
| 10 | M&L for 75mm thick (1:3:6) Type-C2 (using 40mm graded crushed stone aggregate) as in plinth protection / path finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed. |
| 11 | M&L for plain cement concrete (1:4:8) Type-D2 (using 40mm graded crushed stone aggregate) as in levelling course / sub base of flooring complete all as specified and as directed. |
| 12 | M&L provinding cement concrete (1:2:4) B-1 using 20mm graded aggregate as in copings /haunching/ bearing course over brick walls etc and like complete all as specified. |
| 13 | M & L non skid ceramic coloured tiles 600X600 7 to 8 mm thickin floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15mm thick screed bed of CM 1:6 complete. |
| 14 | .Ditto but in skirting over and including 10mm thick backing coat in CM 1:3 complete all as specified and directed. |
| 15 | M&L for coloured glazed ceramic tiles in vertical surface300X 450X 7 mm/300x600x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat of CM 1:3 complete all as specified. |
| 16 | M & L Non - skid ceramic coloured tiles,size 300x300x 7mm thick laid on floor , over and including 15mm thick screed bed in cement slurry and pointed in white cement with pigment to match the shade of the tiles, complete all as specified and as directed. |
| 17 | M&L for rubber moulded glossy chequered cement concrete coloured tiles 30cm x 30cm x 20mm thick, set, jointed and pointed in neat cement slurry in floors over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 18 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; |
| 19 | Dismantling ofstone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed. |
| 20 | M&L 20mm thick granite (of any type) work table rubbed and pre polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixtures of pigment to match with shade of granite complete and ensure best adhesion to surface complete |
| 21 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations |
| 22 | M&L for machine cut cudappah stone slab 20-25mm thick for vertical supports of kitchen platforms and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing of the exposed face complete all as directed and specified |
| 23 | M&L machine cut kota stone slab flooring 20- 25mm thick over and including 20mm screed bed CM(1:4)cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 24 | Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish and including minor grindig complete all as specified and directed. |
| 25 | Taking down Cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, any description complete all as specified and directed. |
| 26 | M&L rendering 15mm thick on stone masonary surfaces other than fair faces of brick surfaces work or stone surfaces in CM 1:6 finished even and smooth without using extra cement |
| 27 | M&L rendering 15mm thick in CM 1:4 on brick /stone surfaces finished even and smooth without using extra cement complete all as specifiwd as directed. |
| 28 | All as above but 10mm thick in CM 1:3 as in ceilingcomplete all as specified and directed |
| 29 | M&L for preparation newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed. |
| 30 | M&L for preparation newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer of same make over external wall surfaces complete all as specified and as directed. |
| 31 | M&L for preparing new plasteredsurfaces of walls and applying two coats of oil bound distemper over a coat of primer of same make over a thin layer of wall care putty complete all as specified and directed. |
| 32 | M&L for preparing old plasteredsurfaces of walls and applying two coats of oil bound distemper over 1mm thick wall care putty including complete removal of existing treatment of any layer on wall complete all as specified and directed. |
| 33 | M&L for preparing old plastered or unplastered surfaces of walls and applying two coats of oil bound distemper complete all as specified and directed. |
| 34 | M&L for preparing old plastered or unplastered surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed. |
| 35 | M&L for preparing old plastered surfaces of ceiling and applying one coat of oil bound distemper complete all as specified and directed. |
| 36 | M&L for preparation of oldplasteredsurfaces of wall/ Ceiling by brooming / wire brushing / removal of loose scales / dusts / unwanted particles manually / mechaincally and applying one coat of white wash complete all as directed and specified. |
| 37 | M&L for preparing old plastered surface of walls and applying one coat of cement based paintcomplete all as specified and directed. |
| 38 | Complete removal ofold decorated surface of wall preparation old plastered surfaces of wall and applying Finishing walls with Acrylic Smooth exterior paint of required shade ,Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) Complete all as specifiedspecified and directed. |
| 39 | M&L for preparation of old steel surfaces of any description and applying one coat of synthetic enamel paint of selected colour complete all as specified and directed. |
| 40 | M&L for preparation of old wooden surfaces of any description and applying one coat of synthetic enamel paint of selected colour complete all as specified and directed. |
| 41 | DismantlingWall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet |
| 42 | M&L for 8 mm thick one side laminated gypsum ceiling board for false ceiling of size 600 x600x mmonGIpowder coated grid work 60 cm x 60 cm with using 36.5 mm x 23.5 mm x1.5 mm thick main tee, 23.5 x 23.5 mm x 1.28 cross tee and 25 x 25x 1.5 mm angles fixed to perimeter of wall for false ceiling including necessary supporting hanger with 4.0 mm dia GI wire and \"J\" bolts washer nuts for securing frame work to ceiling suspended @ 120 cm C/C both ways, size of grid shall be 605 x 605 mm, complete all as directed and specified |
| 43 | M & L for 12mm thick Seamless calcium silicate ceiling madeof 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seamless finishwith and includingGl frame work size of grid (605 mm x 605 mm) direction of Engr-in-charge as per site reqmt seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with andincl thin layer of putty with gypsum binder, sanding the sufrace till smooth surface is obtained and applyingtwo coats of oil bound distemper over acoat of primercomplete all as specified. |
| 44 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick, AZ-150 grade of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantiling of sheets as in roofing/cladding as specified and directed |
| 45 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick, AZ-150 grade of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, bent to shape as required and directed fixed with self tapping screws including dismantling of sheets in roofing/claddingas specified and directed |
| 46 | S&F 2 mm thick Fibre glass reinforced translucent sheetingfixed with coach screw and washer in roof/wall cladding etc including dismantling of sheets as in roofing/cladding complete all as specified and directed. |
| 47 | Dismantling timber scantling, framed in post, rafters, purlines etc over 40 sqcm in section where necessary complete all as specified and as directed. |
| 48 | M&L for MS structural steel work, framed as in trusses purlins, rafter, post etc conforming to grade E-250 (Fe-410W, quality A) including shaped washers including necessary cutting required length, notching drilling, riveting and or welding or connecting with nut bolts with angle cleats, fish plat, gusset plate and also erecting in true position complete all as specified and as directed, |
| 49 | S&F 15 mm dia steel water GI tube medium grade with all fittings / connections & MS clamps / clips and necessary screwingas reqd and fixed with or without concealed to walls & surface of roof slab with and including making good to required surfaces by using white cement and including taking up or down 15mm bore steel / composite / UPVC tubing and connection from any position concealed / exposed complete all as specified and directed. |
| 50 | S&F 20 mm dia steel water GI tube medium grade with all fittings / connections & MS clamps / clips and necessary screwing as reqd and fixed with or without concealed to walls, ceilings or laid in floors including taking up or down 20mm bore steel / composite / UPVC tubing and connection from any position concealed / exposed complete all as specified and directed. |
| 51 | S&Frotational mouldedpolythenewaterstorage tank 500 ltrs(cylindricalvertical with closed top) hoistedand fixed in position incl dismantling existing water tank of any capacity all as specified inSSR Part-Icomplete all as specified and directed. |
| 52 | S&Frotational mouldedpolythenewaterstorage tank 1000 ltrs(cylindricalvertical with closed top) hoistedand fixed in position incl dismantling existing water tank of any capacity all as specified inSSR Part-I complete all as specified and directed. |
| 53 | S&F in repair vitreous china single piece pedestal pattern water closet white\"P\" or \"S\" trap, matching sheet cover andconnection to trap . including making good to floor, complete all as specified. Make Jaquar cat part no: CNS-WHT-851 or Techno commercial equivalent model in KOHLER and ROCA. |
| 54 | S&F in repair 15mm bore chromium plated bib cock fancy type. Make Jaquar cat part no:FLR-CHR-5047N or equivalent model in KOHLER and ROCA. |
| 55 | S&F in repair 15mm bore chromium plated angle cock fancy type.Make Jaquar cat part no:FLR-CHR-5053N or equivalent model in KOHLER and ROCA. |
| 56 | S&F in repair Brass CPwall mixer 3-in-1 for mixing hot & cold water with provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting legs & wall flange and fixed.Make Jaquar cat part no:FLR-CHR-5281N or equivalent model in KOHLER and ROCA. |
| 57 | S&F in repair brass chromium plated overhead shower 100mm round shape single flow with rubit cleaining system fitted to steel pipe or union complete.Make Jaquar cat part no:OHS-CHR-1989 or equivalent model in KOHLER and ROCA. |
| 58 | S&F in repair 15mm bore chromium plated pillar cock fancy type.Make Jaquar cat part no:FLR-CHR-5015 or equivalent model in KOHLER and ROCA. |
| 59 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube andwall hook including making connections and fixed in position complete all as specified. Make Jaquar cat part no:ALD-CHR-577 or Techno commercial equivalent model in KOHLER and ROCA. |
| 60 | S&F in repair for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 10cm wide with chromium plated bracket guard and railing 60cm long.Make Jaquar cat part no:CAN-CHR-1171 N or Techno commercial equivalent model in KOHLER and ROCA. |
| 61 | S&F in repairs chromium plated soap dish approximate size 120x 120x28mm complete all as specified and directed.Make Jaquar cat part no:AKP-CHR-35731P or Techno commercial equivalent model in KOHLER and ROCA. |
| 62 | S&F in repair tubular towel rail, 20mm dia, D type, 60cm longv between flanges Make Jaquar cat part no:AKP-CHR-35711PS or Techno commercial equivalent model in KOHLER and ROCA. |
| 63 | S&F in repair 2-way Bib cock with flange Make Jaquar cat part no:FLR-CHR-5041N or Techno commercial equivalent model in KOHLER and ROCA. |
| 64 | S&F 15 mm dia PVC connections, 450 mm long with PTMT nuts of suitable size at two end complete all as specified and directed. |
| 65 | Supply and fixed in repair 20mm bore PVC brass valve, high pressure with polythene float and fly nut completescrewed for iron pipe or brass ferrule complete all as directed |
| 66 | Supply and fixed in repair 20mm dia gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete |
| 67 | S&F Stainless Steel Kitchen rack (Overall size 24x24x10”) complete all as specified and directed. Make : Cat No. P-310 of Prayag / Blue Star / Nirali |
| 68 | S&F in repair vitreous China, squatting pan, Orissa Pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with PTMT trap of suitable size( P or S type) including connection to trap and to flushing pipe, anti syphonic pipe etc completeincluding provision of cement concrete bedding & making good to floor complete all as specified and directed including taking out old one. |
| 69 | S&F in repairs 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as reqd complete all as specified and directed. |
| 70 | Supply and fixing in repair 600mm X 450mm bevelled edge mirror of selected quality mounted on plastic frame covered back with commercial and fixed on wooden plug with chromium plated brass screws and cup washer complete all as specified. |
| 71 | Supply and fixed in repairsinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on toarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm. |
| 72 | Supply and fixed in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 73 | S&F in repairs Vitreous China wash basin, white/coloured, flat back, size 550x400mm excluding taps, waste chain & plug & porcelain stopper but including brackets and 32mm dia 1mtr long PVC waste pipe. |
| 74 | S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern & flush pipe) inclusing health faucet. |
| 75 | Dismantling cast iron work of any de scription and in any position |
| 76 | S& F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 77 | .ditto- but 75mm bore |
| 78 | S&F 110mm PVC (SWR) bands |
| 79 | S&F 75mm PVC (SWR)bands |
| 80 | S&F PVC(SWR) Nahani trap 75mm bore with SS grating with or without holes incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as directed. |
| 81 | S&F PVC (SWR) cowl 75/100mmdia as required complete |
| 82 | S&F 110mm bore PVC (SWR) junction double,(double T).equal or unequal with access door complete. |
| 83 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in cement concrete and making good disturbed ground and inclusive of removal of debris out side defence land or removal to store complete |
| 84 | Dismantling fencing wire mesh, any type and inclusive of removal to store complete |
| 85 | S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing barbed wire etc) including all necessary drilling, bolting or riveting, embedding in cement concrete, MS flat at bottom etc and similar work confirminng to Fe-290 Gde E-165 complete |
| 86 | S&F MS flats as bands, straps, supports or stays for securing chain link fencing to angle iron postsand welded to post in PCC during embedding complete |
| 87 | S&F Mild steel screws bolts 11 to 15mm dia of neck (machine made) with hexagonal or square heads at one end and screwed at the other end, each screwed end to be fitted with washers and one hexagonal or square nut, n.exc 5 cm long and dia diameter of neck 5 to 10mm complete |
| 88 | Supply only chain link MS galvanised fencing any size or type as directed by Engr-in Charge. |
| 89 | Fixing only chain link, fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete |
| 90 | S&F in repair galvanised 2 strand, steel barbed wir 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including , securing or tying at crossing with and provision of galvanised mild steel wie, staples or steel pins etc as directed each line wire to be measured) complete |
