}

Providing Furniture For Multiplex At Vaikkom, Kottayam District., kottayam-Kerala

Kerala State Film Development Corporation Limited has published Providing Furniture For Multiplex At Vaikkom, Kottayam District.. Submission Date for this Tender is 21-05-2025. Office Furniture Tenders in kottayam Kerala. Bidders can get complete Tender details and download the document.




Tender Notice

49042862
Corrigendum : Providing Furniture For Multiplex At Vaikkom, Kottayam District.
Tender
Indian
Kerala
Kottayam
21-05-2025

Tender Details

Providing Furniture For Multiplex At Vaikkom, Kottayam District.- 1 od174823/2024_2025Supply and installation of work table - 4020 size shall be 1200 Width x 600 Depth x 740 Height. The topshall be made from 25 mm thick pre- laminated board. All the edges are sealed with 2 mm thick PVCedge band all around. Side panels shall be made from 25mm thick pre- laminated paticle board. All theedges are sealed with 2 mm thick PVC edge band on the user side and 0.8 mm on the top and bottomside.The side panels have 2 glide screws each for levelling of the desk. Modesty panel shall be madefrom 18 mm thick pre- laminated particle board. All the edges are sealed with 0.8 mm thick PVC edgeband all around. Freestanding Pedestal shall be made from 18 mm pre- laminated particle board with acombination of 2 mm and 0.8 mm PVC edge band on all the exposed surfaces as per requirement. Thedrawers are provided with suitable slides for smooth operation. All the pedestal drawers are centrallylocked with a single key. 2 od174824/2024_2025Supply and installation of Aristo Table 1200Lx600Dx750H Primary Work Surface Made of 25mm thickMDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed onto top Soft closing access flap with in-build power box are provided on work surface for wire managementSecondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF oneside pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on totop.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated PedestalMade of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thickMDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed onto top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal PanelDrawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening. Pedestals are provided with lock for security. 3 od174845/2024_2025Motion Chair SEAT/BACK ASSEMBLY: The cushioned seat assembly consists of seat base moulded inglass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyesterfabric.The Back is injection moulded in glass filled Polypropylene which is upholstered with Mesh fabric.The back consist of adjustable lumbar support made of injection moulded Polypropylene having anadjustment of 3.0 ±0.1 cm. * Mesh Back Size : 45.5 cm. (W) x 54.0 cm. (H), * Seat Size : 48.5 cm. (W) x49.0 cm. (D).2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam used inseat and back cushion is moulded in Density Min 48 kg/m3, and hardness load 15 ± 2 kgf as per IS:7888for 25% compression.3. TILT MECHANISM, SPINES & SPINE CONNECTOR: The seat and back arefirmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensionalmovement possibility just with a simple lean on the sides or back, without need for complex manualadjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the backmovement during posture changes. The S shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-amide form the back-spine structure involvedin multi-dimensional recline motion.The variable tilt angle recline motion can be adjusted with 3 positionTilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent.4a.ADJUSTABLE ARMRESTS: The assembly consists of armrest housing sliding over the armreststructure,both moulded in glass-filled Poly-amide. The height adjustment feature is button operatedhaving adjustment of 6.6±0.5cm. The Armrest Top is made up of integral skin PU moulded over plasticinner moulded in glass-filled Poly-amide. 5. PNEUMATIC HEIGHT ADJUSTMENT: The seating heightcan be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm 6. PEDESTALASSEMBLY: The pedestal is injection moulded in glass-filled Poly-amide and fitted with 5 nos.twin wheelcastors. The pedestal is 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors.7.TWINWHEEL CASTORS: 5 nos. twin wheel castors are injection moulded in Poly-amide having 5.0±0.1cmwheel diameter and assembled to the pedestal. 4 od174877/2024_2025Supply and installation of Enterprise 1200 Table without CPU Hanger size shall be 1200 Width mm x 600Depth mm x 728 Height mm. Top shall be 18mm thick Pre laminated particle board all work surfaceedges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18mm thick Pre laminated particle board. The Rectangular frame shall be fabricated component in 1.2 mmthick CRCA, Finish: powder Coat(epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm1.2 mm thick MS ERW ATube finish powder coat (epoxy polyster). The plastic cap for cable travel shallbe injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall behaving shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawerfront shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handleand leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powdercoat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) 5 od174908/2024_2025Unwind chair w/o arm -The Seat and Back should be made up of injection moulded indoor gradePolyPropylene compound SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) BACK SIZE : 51.6 cm. (W) x 40.5cm. (H) The powder coated ( DFT 50±10 microns ) welded tubular frame should be made from 0 2.22 ±0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. Theshoes should be made of indoor grade PolyPropylene compound and snap fitted with tubularframe.Overall Dimensions of Chair- Seat Height - 45.0 cm. Height - 84.5cm.Width-52.5 cm and Depth-55.8 cm. 6 od174889/2024_2025Oxbo mid back chair -Providing, supplying and placing of Mid Back Chair. SEAT ASSEMBLY: The seatassembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabricupholstery covers and moulded Polyurethane foam.plywood , SEAT SIZE: 47.0 cm. (W) x 48.0 cm.(D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbarsupport for extra comfort. The back should be upholstered using double layer spacer mesh fabric withhigh tenacity yarn.BACK SIZE : 46.5 cm (W) x 60.5 cm (H).HIGH RESILIENCE (HR) POLYURETHANEFOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests should be injection moulded fromblack Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should bedesigned with the following features:• 360° revolving type.• 17° ±2° maximum tilt on pivot at centre •Upright position locking. • Upright position locking. • Tilt tension adjustment. PNEUMATIC HEIGHTADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0±0.3cm.TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injectionmoulded in Black Polypropylene.PEDESTAL ASSEMBLY: The pedestal should be injection moulded inblack 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)TWIN WHEEL CASTORS: The twin wheel castorsshould be injection moulded in black nylon.Overall Dimensions of Chair Seat Height - min 43.3 to max54.3cm.Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. 7 od174918/2024_2025Supply, Fitting & Fixing of Filing cabinet. Overall size shall be 1320mm(H) X 470mm(W) X 620mm(D). Allthe components shall be made of CRCA . It should have 1 Point Locking Mechanism and a Rigid KnockDown Construction. The Top, Side & Drawer Front thickness should be 0.7mm. The Frames, Drawer-inside cover and Side Back Side thickness should be 0.6mm. The Back, Bottom and Drawer thicknessshould be 0.5mm. Easy to grip Full length Recess Handle shall be integrated into Metal Drawer for easypull out convenience. There shall be a Snap on type plastic label holder on Drawer Fronts. In addition, 28‘Ezee’ / ‘Visa’ files (Foolscap) from front to back of thickness 20mm per drawer can be hanged in Filingcabinet. The Centralized locking System shall be provided along with Shooting Bolt Mechanism and 10Lever Cam Lock. The VFC should have anti-tipping arrangement which ensures that when one drawer isopened for use, it does not allow other drawers to be opened. The High Quality Precision Ball Slide shallbe provided with Drawer Load capacity of max 40 kg and UDL for 75,000 cycles (BS). Plain Triangularplate pop should be riveted at the bottom corners for rigidity. Optional Accessories like Drawer Partitionand Cradle for hanging A4 file folders front to back should also be available. The finishing shall includeEpoxy powder coated to the thickness of 50 microns (+/- 10). 8 od174906/2024_2025PISA sofa-Providing, supplying and placing of three seater sofa. SEAT FOAM : The seat is made up ofPU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2kg/cu, upholstered with fabric or leatherette.BACK FOAM : The back is made up of PU foam in Density28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholsteredwith fabric or leatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hotpressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoidof major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted overunderstructure for cushioning purpose.LEG ASSEMBLY : It is a welded Assembly made in Stainless steel(grade SS 202) tube & plate with plastic endcap. 3 str Width (W): 206.0 CM. Depth (D): 90.5 CM. Height(H): 85.5 CM. Seat Height (SH): 45.0 CM. 9 od174907/2024_2025Providing, supplying and placing of PISA sofa. SEAT FOAM : The seat is made up of PU foam in Density28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholsteredwith fabric or leatherette.BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtrwith two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric orleatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood[moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots &surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure forcushioning purpose.LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202)tube & plate with plastic endcap. 1 str Width (W): 86.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM.Seat Height (SH): 45.0 CM.

Corrigendum Details

Sr No CorrigendumDate Corrigendum CorrigendumType NewSubmissionDate
1 17-05-2025 Date Corrigendum Date 21-05-2025

Key Value

Document Fees
INR 1188 /-
EMD
INR 12581.0 /-
Tender Value
Refer document
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail