Tender For C/O 04 Nos. Toilet Block In Parade Ground At Ssb Academy Bhopal.; 1 C/o 04 Nos. toilet blocks in parade groundat SSB Academy, Bhopal. 2 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.All kinds of soil 3 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil anddisposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. 4 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m 5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 6 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 7 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived fromnatural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 8 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 9 Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. 10 Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete 11 Lintels, beams, plinth beams, girders, bressumers and cantilevers etc. 12 Columns, Pillars, Piers, Abutments, Posts and Struts- 13 Reinforced cement concrete work in beams, suspended floors, roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinthlevel up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand(zone-III) derived from natural sources : 3 graded stone aggregate20 mm nominal size derived from natural sources). 14 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 15 Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and accessplatform 16 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 17 30 mm red sand stone sun-shade (chisel-dressed) supported on redsand stone brackets, fixed in walls with cement mortar 1:4 (1 cement :4 coarse sand), including finishing complete. 18 Providing and laying Polished Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stone slabover 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade includingrubbing, curing and polishing etc. all complete as specified and asdirected by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/RubyRed or equivalent 19 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) 20 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 21 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite wor 22 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 23 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm 24 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm 25 Providing and fixing aluminium handles, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm 26 Providing and fixing factory made door frame (single rebate) made out of solid foam PVC extruded profile of minimum 60 mm width and minimum30 mm thickness, having homogenous fine cellular structure and integralsmooth outer skin. The frame’s vertical and horizontal members to be mitered cut and joined together with PVC solvent adhesive / cement andboth corners strengthened with fully threaded steel screws (of required size)fixed diagonally. The door frame is to be fixed to door jambs using 6 Nos. SS 304 grade minimum 8 mm dia CSK Phillips stainless steel self tapping screws/fasteners with PA6 grade polyamide sleeves both of required size, and gap if any between the door frame and the jamb must be filled with clear silicon, complete as per direction of the Engineer-in-Charge. 27 Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1mm, painted with primer , all four corners of reinforcement to be welded or sealed.Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturers specifications and direction of Engineer-in-charge. Decorative finish (both side wood grained finish) 28 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 29 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than50 gram/litre 30 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 31 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. 32 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. : 20 mm nominal outer dia Pipes 33 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply including all CPVC plain &brass threaded fittings This includes jointing of pipes & fittings with onestep CPVC solvent cement, trenching, refilling & testing of joints completeas per direction of Engineer in Charge.External work32 mm nominal dia Pipes 34 Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, IS : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank. 35 Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length: 15 mm nominal bore 36 Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge 37 Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks 38 Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. 39 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :100 mm diameter 40 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :100 mm diameter S.W. pipe 41 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standarddesign :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 42 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 43 Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 andIS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sideswith required EPDM rubber/ neoprene gasket etc. Aluminium sectionsshall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) :For fixed portionPolyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) 44 For shutters of doors, windows & ventilators includingproviding and fixing hinges/ pivots and making provisionfor fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall bepaid for separately)Polyester powder coated aluminium (minimumthickness of polyester powder coating 50micron) 45 Providing and fixing glazing in aluminium door, window, ventilator shuttersand partitions etc. with EPDM rubber / neoprene gasket etc. complete asper the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 46 Providing and fixing floor mounted, white vitreous china single piece water closet make Jaquar model no LYS-WHT-38851S300UFSMN Single piece-WC or equivalent or as per approved make by Engineer-in-charge with UF Soft Close Slim Seat Cover, Fixing Accessories, Accessories set and Cistern Fittings, Size: 370x670x720 mm, S Trap-300mm including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 47 Providing and fixing table top wash basin of size 565x420x140 mm without15 mm dia CP Brass single hole basin mixer of make Jaquar Kubix model no KUS-WHT-35935 or equivalent or as approved by Engineer-in-charge, with all CP fitting including removing old wash basin and brackets, cutting and making good the walls wherever required etc. complete as per direction of engineer in charge. 48 Providing and fixing toilet Roll holder with stainless steel flap of make Jaquar model no AKP-35753PS or equivalent or as approved by Engineer-in-charge. 49 Providing and laying anti skid vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm 50 Providing and fixing 1st quality 300X600 mm digitally printed ceramic wall tiles(thickness to be specified by the manufacturer), of Kajaria, Somany ,RAK or equivalent make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 51 Providing and fixing Sensor Faucet single leverfor wash basin of make Jaquar Kubix Prime model no SNR-35019PM or equivalent oras per approved make by Engineer-in-charge for wash basin(Battery Operated) including all fittings complete as per direction of Engineer -in-charge. 52 Providing and fixingsingle lever quarter turn basin pillar cock for wash basin of make Jaquar Kubix Prime model no KUP-35001PM or equivalent oras per approved make by Engineer-in-chargeincluding all fittings complete as per direction of Engineer -in-charge. 53 Providing and fixing angle valve/angular stop cockof make Jaquar Kubix Prime model no KUP-35053PM with Wall Flange or equivalent oras per approved make by Engineer-in-chargeincluding all fittings complete as per direction of Engineer -in-charge. 54 Providing and fixing white vitreous china battery basedsensor operated urinal of make Jaquar model no URS-WHT-13255 Size: 480x300x740mm with Sensor Flushing Valve model no SNR-CHR-51097 for Urinal with Complete Kit (Battery Operated)(Suitable For Urinal URS-WHT-13255)or equivalent or as per approved make by Engineer-in-charge having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. 55 Providing and fixing urinal partitions of size H: 900 mm W: 450 mm make Jaquar Model No. 1810-UCJSE-CHR-810UC450X or equivalent or as per direction of Engineer-in-charge Curved shapedwith 8 mm thick frosted glass in chrome finish including all fitting , brackets etc. complete. 56 Providing and fixing 2 Way Bib Cock with Wall Flange of make Jaquar Kubix Prime model no KUP-35041PM or equivalent oras per approved make by Engineer-in-chargeincluding all fittings complete as per direction of Engineer -in-charge. 57 Providing and fixing CP brass Bib Cock with Wall Flange of make Jaquar Kubix Prime model no KUP-35037PM or equivalent oras per approved make by Engineer-in-chargeincluding all fittings complete as per direction of Engineer -in-charge. 58 Providing and fixing Hand Shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish and Wall Hook with N.R.V (Back Flow Preventer) of make Jaquar model no ALD-579 or equivalentor as per direction of Engineer in charge. 59 Providing and fixingBottle Trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange of make Jaquar model no ALD-769L300x190 or equivalent including all complete as per direction of Engineer-in-charge. 60 Providing and fixingCP brass Waste coupling 32mm Size Full Thread with 80mm height of make Jaquar model no ALD-705 or equivalent including all complete as per direction of Engineer-in-charge. 61 Providing and fixing450mm Long Braided Hose with M10X1Nipple, 15mm Nut, O-Ring & Rubber Washerof make Jaquar model no ALD-803AB or equivalent including all complete as per direction of Engineer-in-charge. 62 Providing and fixing soap dispenser with glass bottle of make Jaquar model no ACN-1135N or equivalent or as approved by Engineer-in-charge. 63 Providing and fixing looking mirror of size 1500x900 mmwith 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers all fitting and fixture etc. complete as per direction of Engineer-in-charge. 64 Providing and fixing Premiun QualitygranitePearl Blue18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut forwash basin counters, facias and similar locations of required size laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 Coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 65 Providing and fixing Single Towel Rail 600mm Long,Stainless Steel of make Jaquar model no AKP-35711PS or equivalent or as per approved make by Engineer-in-charge complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 66 Providing and fixing 18 mm thick Wood -plastic Composites(WPC) board in partitions racks etc completeas per direction of Engineer-In-Charge. 67 Providing and fixing floor trap includingall complete as per direction of Engineer-in-charge. 68 Providing and fixing CP brass grating of approved quality and colour.Circular type 125 mm nominal dia with 25 mm waste hole 69 Providing and fixing CP brass grating of approved quality and colour.Circular type 100 mm nominal dia 70 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required-group B 71 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required-2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 72 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.-3 x 1.5 sq. mm 73 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required(Sample of switch/socket to be pre approved by the engineer in charge) 74 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required - 25mm 75 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A switch 76 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 4 Module (125mmX75mm) 77 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 6 Module (200mmX75mm 78 Supplying and fixing of250 mm sweep ,Ventilair DX plastic body refresher fan make Havells/CG/USHA to fixeddirectly on existing duct with complete testing etc as reqd 79 Supplying and fixing of 18 watt LED Lumanaire round shape,suitable to fix on fall ceilingmake CG/havells as per direction of engineer in charge 80 Supplying and fixing of 12/18watt LED lumanaire make philips/CG/Havells , 2 feet long,white in colour, on existing wallwith complete connection etc as reqdmake CG/havells as per direction of engineer in charge 81 Supplying and fixing of 20 watt LED batten(complete set), white in colour make havells/CG to be fixed firectly on wall/fall ceiling with complete testing etc as reqd 82 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 120 sq. mm
