Tender For Constr Of 04 X Toilet Block For Women Ocs At Ota Gaya; 1 Surface excavation not exc 30 cm deep and averaging 15 cm in hard/dense soil complete all as specified and directed by Engr-in-Charge. 2 Excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge. 3 Removing excavated material exc. 250 m but n exc. 500 m and depositing where complete all as specified and directed by Engr-in-Charge. 4 Returning, filling in, incl spreading, levelling, watering & well ramming in layers n. exc 25 cm in soil complete all as specified and directed by Engr-in-Charge. 5 M & L PCC in foundations, filling and mass-concrete type D2 (1:4:8) using 40 mm graded stone aggregate complete all as specified and directed by Engr-in-Charge. 6 M & L RCC M 25 DESIGN MIX using20 mm graded aggregate in beams, cantilevers, lintels over 1.5 m span complete all as specified and directed by Engr-in-Charge. 7 M & L RCC M 25 DESIGN MIXusing 20 mm graded aggregate in Foundations, incl rafts, footings, foundation beams; plinth beams; bases for columns and mass concrete complete all as specified and directed by Engr-in-Charge. 8 M & L RCC M 25 DESIGN MIX using 20 mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge. 9 M&L RCC M 25 DESIGN MIX using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge. 10 M & L RCC M 25 DESIGN MIX using 20 mm graded aggregate in Chajjas complete all as specified and directed by Engr-in-Charge. 11 Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge. 12 Form work to sides of concrete foundations, footings, bases of columns,sides & soffits of foundation & plinth beams and similar work Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge. 13 Form work to sides of pillars, posts, struts, piers,columns, and stanchions Rough finished surfaces of concrete Square, rectangular or polygonal complete all as specified and directed by Engr-in-Charge. 14 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge. 15 M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips qualitycomplete all as specified and directed by Engr-in-Charge. 16 M&L Mild steel TMT bars 5mm dia & over,upto and including 10mm dia as in stirrups ,spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed by Engr-in-Charge. 17 M&L Brick work using old size bricks with sub class B bricks straightor curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed by Engr- in- charge. 18 M & L for Brickwork with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4)complete all as specified and directed by Engr-in-Charge. 19 M&L for10 mm thick rendering in cement mortar 1:6 onfair face of brickwork or concrete surfaceandfinished even & smooth (without using extra cement) complete all as specified and directed by Engr-in-Charge. 20 M&L for15mm thick rendering in cement mortar 1:4 onfair face of brickwork or concrete surfaceandfinished even & smooth (without using extra cement) complete all as specified and directed by Engr-in-Charge. 21 Supply only Integral water proofing compound complete all as specified and directed by Engr-in-Charge. 22 M&L for05 mm thick rendering in ceiling on brickwork or concrete surfacein cement mortar 1:3 andfinished even & smooth (without using extra cement) complete all as specified and directed by Engr-in-Charge. 23 M& L for 1 mm thick of white putty/K white wall care putty in two coats on new plastered surfaces and making the surface and making the surface uniform &smooth on walls complete all as specified and directed by Engr-in-Charge. 24 M & L for preparing new plastered surface of wall and applying two coats of distemper oil Sqm emulsion white or tinted over a coat of chalk whiting as a preparatory to distempering complete all as specified and directed by Engr-in-Charge. 25 M & L for preparation of newly plastered surface and applying two coats of white wash as in ceiling complete all as specified and directed by Engr-in-Charge. 26 M & L for preparing newly plastered walls surfaces and applying twocoats of cement base paint over one coat of primer complete all as specified and directed by Engr-in-Charge. 27 M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-in-Charge. 28 M&L for spreading and levelling n.exc 25cm thick including well ramming incl watering all asspecified and directed by Engr-in-Charge 29 M & L for Hard core of Broken bricks gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface complete all as specified and directed by Engr-in-Charge. 30 M & L 75mm thick PCC type C-2, (1:3:6) using 20mm graded stone aggregate finished even & smooth without using extra cement as in plinth protection/Path and joint will be filled with bitumen complete all as specified and directed by Engr-in-Charge. 31 M & L 75mm thick PCC type D-2, (1:4:8)in sub base floor complete all as specified and directed by Engr-in-Charge. 32 M & L 25mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate as in flooring including finishing cement concrete rough surface without using extra cement complete all as specified and directed by Engr-in-Charge. 33 M & L for non skid ceramic coloured tiles of 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exc 0.11 Sqm but n.exc 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge. 34 M & L for Glazed ceramic coloured tiles of size450X 350X 7mm thick as on vertical surfaces such as skirting, dados and rises to steps etc. over 10mm thick rendering in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed by Engr-in -charge. 35 S&F vitreous china wash basin, white, flat back size 550x400mm excluiding taps, chain and plug including waste pipe, brackets, 32 mm dia CP coupling cutting for and pinning in ends for brackets or ercting stand complete all as specified and directed by Engr-in-Charge. 36 S& F Vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, but excuding flushing cistern and flush pipe complete all as specified and directed. 37 S & F 10 litre capacity PVC valveless, syphonic action type, flushing cistern with flush pipe, low level white with inlet, ball valve, float and handle including brackets, 110mmPVC (SWR) P-trap complete. 38 S & F 15 mm dia bore fancy type chromium plated bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge. 39 S & F of Pillar taps 15 mm, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charge. 40 S & F white soft closing seat cover for pedestal pattern water closet including fixing bolts complete all as specified and directed by Engr-in-Charge.. (Make : Jaguar/Hindware) 41 S & F brass chromium plated health faucet 15 mm with flexible tube (1.5 m long) of stainless Each steel provided rubber hose and wall hook etc complete all as specified and directed. (Make Jaguar/Hindware) 42 S & F vitreous China Urinal, Half stall type, white incl providing and fixing plugs, bedding Each urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing of flush pipe, grating and union for discharge pipe complete all as specified and directed by Engr-in-Charge. 43 M&L Cast iron 100mmnahanitrap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr-in-Charge. 44 S & F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed by Engr-in-Charge.(Minimum weight Each 60gms) 45 S & F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed by Engr-in-Charge. 46 S & F 6mm thick looking mirror of Ist quality glass, mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete.(make:Saint Gobain/ModiFloat) 47 S & F 15 mm dia bore fancy type chromium plated two way bib taps/angle valve, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.(make : prayag,seiko,parryware) 48 S&F fancy type chromium plated Stop valves/angle valve , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-charge. 49 Supplying and laying of CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 including alll fittings on walls/ceilings or in floors including necessary cutting/chasing of walls and floors complete all as specified and directed. 50 Supplying and laying of CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 including all fittings on walls/ceilings or in floors including necessary cutting/chasing of walls and floors complete all as specified and directed. 51 S & F of 25mm Male Brass Threaded Adaptor (MTA/ MBTA) or Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and directed by Engr-in-Charge. 52 S & F of 20mm Male Brass Threaded Adaptor (MTA/ MBTA) or Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and directed by Engr-in-Charge. 53 M&L for 1000 ltr capacity White rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including all accessories complete all as specified and directed by Engr-in-Charge. 54 S&F in 25mm dia bore CPVC gate valves with handle or wheel head, screwed both ends for pipe and fixed complete all as specified and directed by Engr-in-Charge. 55 S&F in 20mm dia bore CPVC gate valves with handle or wheel head, screwed both ends for pipe and fixed complete all as specified and directed by Engr-in-Charge. 56 S&F 25mm dia ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and directed by Engr-in-Charge. 57 S&F PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore complete all as specified and directed by Engr-in-Charge. 58 S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall of 110 mm bore dia complete all as specified and directed by Engr-in-Charge. 59 S&F PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore complete all as specified and directed by Engr-in-charge. 60 S&F PVC (SWR) vent cowl of 110 mm bore dia complete all as specified and directed by Engr-in-Charge. 61 S & F 110mm pvc (SWR) bends any radius provided with access door all as specified and directed by Engr-in-charge. 62 S & F of PVC (SWR) junction angle , (Single T) 110mm bore eqal or unequal with access door all as specified and directed by Engr-in-charge. 63 Solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colur PVC sheet reinforced with ms squre tube, supplying &fixing in opening as complete all as specified and directed by Engr-in-charge. 64 S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tube for top & bottom rail. MS frame shall be covered with heat moulded PVC”C” channel having a PVC steel strip of 20mm width stuck inside with solvent cement for style and plain coloured PVC sheet for top rail lock rail &bottom rail on either side &as gap insert for top rail and bottom rail paneling of plain coloured PVC sheet to be fitted in MS frame welded / sealed to style &rails with suitable PVC sheet beading. And jointed together with solvent cement, supplying and fixing in the frames at site as per specification & drawing complete all as specified and directed by Engr-in-charge. 65 Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engr-in-Charge. 66 S&FBrass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges as complete all as specified and directed by Engr-in-Charge. 67 S & F Aluminiumhandle cast type anodized 100mm size complete all as specified and directed by Engr-in-Charge. 68 S & F Aluminium, anodized, barrel tower bolts of extruded section 200mm long complete all as specified and directed by Engr-in-Charge. 69 S & F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engr-in-Charge. 70 S & F Aluminum alloy, anodized, sliding door bolt with hasp & staple (Bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy size 250mm long complete all as specified and directed by Engr-in-Charge. 71 M&L Water proofing treatment on Non approachable / non accessible and approachable roof surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer , properly cleaning & drying the concrete surfaces complete.(i) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm(ii) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces.(iii) Laying unrolled over the bitumen coated surface ,APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application with 100 mm over laps shall be sealed by flame as per manufacturers instructionincluding aluminium paintcomplete all as specified and directed by Engr- in- charge. 72 Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed by engr-in-charge. 73 Excavating over areas exc 1.5 m but n.exc 3.00 mtr deep and getting out in Hard/dense soil complete all as specified and directed by Engr- in- charge. 74 Removal of excavated materials to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engr- in- charge. 75 Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter of rough finished surface of concrete complete all as specified and directed by Engr- in- charge. 76 M & L RCC M 25 DESIGN MIXusing 20 mm graded aggregate in Foundations, incl rafts, footings, foundation beams; plinth beams; bases for columns and mass concrete complete all as specified and directed by Engr-in-Charge. 77 M&L RCC M 25 DESIGN MIX using 20 mm graded aggregate in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed by Engr- in- charge. 78 M&L RCC M 25 DESIGN MIX using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge. 79 M&L Broken brick bats Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed by Engr- in- charge. 80 M&L Brick work using old size with sub class ‘B’ bricks in one brick thick honey combwalling, built in cement mortar 1:4 complete all as specified and directed by Engr- in- charge. 81 M&L for point wiring complete with PVC insulated unsheathed FRLS multi stranded copper conductor cable conforming to IS:694 of size 1.5 Sqmm two single core drawn through in and including PVC conduit pipe 20mm dia medium grade ISI marked complete with one run of PVC insulated unsheathed FRLS multistranded copper conductor cable 1.5 sqmm single core green colour earth wire and connecting to earth dolly incl colour coding of cable shall be for phase, neutral and earth wire as specified in MES SSR Part-I 1991 with provn of sunken galvanised not less than 1.12 mm thick MS sheet pressed terminal boxes concealed on wall, with 3 mm thick laminated sheet top cover ISI marked. Make: Hylem/Anchor for fixing of switches/socket/regulator with screws complete including making good of disturbed surface of wall/ceiling/floor complete area in same specification as per existing all as specified and directed. 82 (a) One light/fan point controlled by one, one way switch 5 Amps 83 (b) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board. 84 (c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board. 85 Description all as per item No. 1 here in before but 3/5 pin socket outlet point 15 amps independant, with cables of size 2.5 sqmm multistranded, PVC insulated unsheathed FRLS copper conductor cable and 1.5 sqmm PVC insulated unsheathed FRLS copper conductor cable as earth continuity conductor connected to common earth dolly all in separate PVC concuit medium grade not less than 20mm dia ISI marked incl provn of GI sunken box thickness not less than 1.12 mm & 3 mm thick laminated hylem sheet top cover of required size all as specified and directed. 86 S&F switch piano flush button single pole one way 5 Amp 87 S&F ceiling rose, surface bakelite 65x50mm 2 to 3 terminal 88 S&F socket outlet 2-in-1, 5 pin, 5 amp flush type. 89 M&L Switch socket combination2 in 1, 3 pin, 5/15 Amp Flush type universal 90 S&F sheet metal enclosure distribution board SPN, 8 ways 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable mounting MCBs all as specified directed. 91 S&F MCB Single pole and neutral, 240 Volts, 40 to 60 Amps, all as specified and asdirected. 92 S&F MCB Single pole, 240 Volts, upto 40 Amps all as specified and as directed. 93 S & F LED street light fitting 35/36 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection with pre wired and necessary mounting arrangements and provision of 2.5 Sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engr-in-Charge. 94 S&F exhaust fan, steel body AC single phase 230V of Size 300 mm sweep with, blades and frame and louvers with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embeded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to fitting complete ass as specified and as directed. 95 S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouputboxtype fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired andnecessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. 96 M & L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type ofsoil/strata and testing on completion. Note:- (i) The unit rate includes earth lead and protection pipe up to maximum 7.5 mtr from earth plate to earth point/test point. (ii) Earth pit shall be constructed minimum 0.5 mtr away from earth. 97 Supply, laying and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electricpower cable 1100 volts with stranded aluminium conductorof size 16 sqmm 2 core laid in trenches or under road complete all as specified and as directed. (Note: Excavation, sand and brick work will be measure & paid separately). 98 Excavationintrenches not exceeding 1.5 m wide & not exceeding 1.5 mtr deep for laying of cable and getting in hard/dense soil complete all as directed. 99 Returning, filling in with approved excaveted soil including spreading, leveling, watering & well ramming in layersnot exceeding 25 cm thick complete all as directed. 100 Removing of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as directed. 101 Burnt bricks sub class B laid flat dry acroos the cable for cable protection all as specified and directed. 102 Sand cushioning to UG cable 8cm thick before laying the cable and 15cm above the cable, stretching and testing of cable complete all as specified and directed. Note: (i) Consolidated/ Punned sand shall be considered for purpose of payment (ii) Sand shall be same as specified for plastering work. 103 Supply and laying river bed fine sand in trenches/ ducts 15 cm under cable and 8 cm above the cable for cushioning / protection to cable including spreading, levelling and get thick 18cm after hand punning complete all as specified and directed at site.
