Tender For Repair And Maintenance Of Certain Steel And Other Furniture At Ge Ima Dehradun; 1 Charpoy GI pipe ( Drg No FD-220) 2 S & F in repairs long rail made of 32 mm dia GI tubing medium grade ISI marked 1.88 metre long, threaded at both ends and fixing to 3 way 32 mm dia GI elbow ISI marked heavy duty of charpoy.Make : Jindal/Ravindra/Tata 3 Conversion of 32 mm dia long rail obtained from item No 1.01 above two short rail after cutting and one short rail threading both ends and fixing to 3 way 32 mm dia existing elbow. Note : Count one short rail each for this item 4 Conversion of 32 mm dia short rail obtained from item No 1.02 above two leg after cutting and one leg threading one ends fixing to 3 way 32 mm dia existing elbow at one end threaded and cover the other end with hard rubber/PVC shoe.Note : Count one leg each for this item 5 S & F in repairs 3 way 32 mm dia GI elbow ISI heavy duty marked complete as per specified. 6 S & F in repairs check nuts of 32 mm dia ISI marked complete as per specified. 7 S & F in repairs 12 mm BWR phenol bonded commercial plywood of existing size including providing 50mm wide strip made out of 6mm thick plywood for filling gap between plywood sheet and short rails including replacement of bolts and nuts for fixing of plywood. Make - Archid Ply/Green Ply/CenturyPly 8 S & F in repairs MS flat of size 40x4mm with two Nos nut & bolts as stiffner shall be fitted for support of plywood. 9 S&F FMN Holder duty welded and dismentling the unsv one 10 Converstion of Charpoy GI pipe ( Drg No FD-220) With Newar into Hard Top 11 S & F in repairs long rail made of 32 mm dia GI tubing medium grade ISI marked 1.88 metre long, threaded at both ends and fixing to 3 way 32 mm dia GI elbow heavy duty of charpoy.Make : Jindal/Ravindra/Tata 12 Conversion of 32 mm dia long rail obtained from item No 2.01 above two short rail after cutting and one short rail threading both ends and fixing to 3 way 32 mm dia heavy duty existing elbow. Note : Count one short rail each for this item 13 Conversion of 32 mm dia short rail obtained from item No 2.02 above two leg after cutting and one leg threading one ends fixing to 3 way 32 mm dia existing elbow at one end threaded and cover the other end with hard rubber/PVC shoe.Note : Count one leg each for this item 14 S & F in repairs 3 way 32 mm dia GI elbow ISI marked heavy duty complete as per specified. 15 S & F in repairs check nuts of 32 mm dia ISI marked complete as per specified. 16 S & F in repairs 12 mm BWR phenol bonded commercial plywood inlieu of old Newar including providing 50mm wide strip made out of 6mm thick plywood for filling gap between plywood sheet and short rails including replacement of bolts and nuts for fixing of plywood. Make - Archid Ply/Green Ply/CenturyPly 17 S & F in repairs MS flat of size 40x4mm with two Nos nut & bolts as stiffner shall be fitted for support of plywood. 18 S&F FMN Holder duty welded and dismentling the unsericeable one. 19 Almirah steel large(FD-67/1031) 20 S & F Lock 7 lever with duplicate keys components of Almirah steel medincluding dismantling unservicable one all as specified and as directed(Make of Lock- Harrison) 21 S & F stainless steel Handle 100 mm size chromium plated Heavy components of Almirah steel medincluding dismantling unservicable one all as specified and as directed 22 S & F 3 way locking devicewith necessary fittings and painted with one coat of synthetic enamel paint of approved shade & quality over a coat of primer. 23 S & F leg made of 1mm thick CRCA sheetduly welded/riveted and painted with one coat of synthetic emamel paint of approved shade & quality over a coat of primer. 24 S & F door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with 7 leverlock with duplicate keys- 01 No,key hole and painting with one coat of synthetic enamel paint of directed shade by Engr-in-Charge over a coat of primerinside and outside Two coat of spray painting of Hammertonepaint (pattern of hammer tone shall be 0.06 gram silicon/kg) shall apply after preparation of surface all as specified and shown on drawing.Note for steel painting;- All steel surface shall be done with spray painting)(Make of Lock- Harrison) 25 S & F shelves made of 1mm thick CRCA sheetwelded/riveted and painted with one coat of synthetic emamel paint of directed shade by Engr-in-Charge over a coat of primer. 26 Preparation of old paintedinner steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of synthetic enamel paint (spray painting) of approved quality including dents/bends all as specified and as directed.Note: Paint shall be make of Asian/Berger/Shalimar and shade of colour as per direction of Engr-in-Charge. 27 Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) of approved qualityincluding dents/bends all as specified and as directed.Note Paint shall be make of Cosmos/MRFVapcoure and shade of colour as per direction of Engr-in-Charge/GE. 28 Table office clerk steel (FD-84/1003,1004 ) 29 S & F following components of Table office cleark steelincluding dismantling unservicable one all as specified and as directed.Drawer made of 1mm CRCA sheetincluding painting with synthetic enamel paint of approved shade & quality over a coat of primer both inside and outside including preparation of surfaces and repairing inter locking system and providing new lock 6 lever to top drawer. 30 Leg/stiffener25 x 25 x 1.6mm thick MS squire pipe duly welded to the frame and painted with one coat of synthetic enamel paint over a coat ofprimer 31 Lock of 4 levers with duplicate keys of approved size 32 Top made of 18mm thick pre-laminated MDF board of approved shade duly post forming laminates all around complete Table office Cleark 33 PVC shoe 34 Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying one coat of synthetic enamel paint of approved shade & quality both inside and outside complete all as specified and as directed 35 Renewal of following unserviceable parts of Table tublar/Allwyn steel with suitable new parts of existing shape & size complete to match the original and directed by Engr-In-Charge.FD-119 36 Top made of 18mm thick pre-laminated MDF board of approved shade duly edgin with Post forming all around complete Table . 37 S&F New lock of 4lever with duplicate key of approved quality. (Make: Godrej/Harrison/Link/Lico) 38 Repair of u/s drawer as shown on drgand directed by Engr-In-Charge. 39 S&F of Rubber Caps 40 M&L for two or more coat spray painting of synthetic enamel paint on old painted surface with high class finish, including necessary scrapping, denting/welding and leveling with filling paste as specified & directed by Engr-In-Charge. (Make: Asian/ Berger/ Nerolac). 41 Table office officer Steel (FD-84/1003,1004 ) 42 S & F following components of Table dinning ORs steelincluding dismantling unservicable one all as specified and as directed.Drawer made of 1mm CRCA sheetincluding painting with synthetic enamel paint of approved shade & quality over a coat of primer both inside and outside including preparation of surfaces and repairing inter locking system and providing new lock 6 lever to top drawer. 43 Leg/stiffener25 x 25 x 1.6mm thick MS squire pipe duly welded to the frame and painted with one coat of synthetic enamel paint over a coat ofprimer 44 Lock of 4 levers with duplicate keys of approved size and make. 45 Side panel made of 1mm CRCA sheet including painting with synthetic enamel paint of approved shade of approved quality over a coat of primer both inside and outside including preparation of surfaces. 46 Top made of 18mm thick pre-laminated MDF board of approved shade duly duly post forming laminates all around complete Table office Officer Steel 47 PVC shoe 48 Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying one coat of synthetic enamel paint of approved shade & quality both inside and outside complete all as specified and as directed 49 Renewal of following u/s parts of Modular Workstation with suitable new parts of existing shape & size complete to match the original as shown on drgand directed by Incharge. TP 50 S&F of 45mm (W) X 580mm (L) Powder coated Profile Cover shall be of die cast made up of 1.5mm thick aluminium with a waterfall edge for a continuous transition from horizontal to vertical trim. 51 S&F of 45mm (W) X1200mm (L) Powder coated Profile Cover shall be of die cast made up of 1.5mm thick aluminium with a waterfall edge for a continuous transition from horizontal to vertical trim. 52 S&F of 45mm (W) X 880mm (L) Powder coated Profile Cover shall be of die cast made up of 1.5mm thick aluminium/PVC with a waterfall edge for a continuous transition from horizontal to vertical trim. 53 S&F of1200mm (L) Powder coated Half Round Profile Cover for 45mmx45mm profile shall be of die cast made up of 1.5mm thick aluminium/PVC with a waterfall edge for a continuous transition from horizontal to vertical trim. 54 S&F of 100mm (W) x 555mm (L) Powder coated Raceway Cover shall be of die cast made up of 1.5mm thick aluminium/PVC with a waterfall edge for a continuous transition from horizontal to vertical trim. 55 S&F of 100mm (W) x 855mm (L) Powder coated Raceway Cover shall be of die cast made up of 1.5mm thick aluminium/PVC with a waterfall edge for a continuous transition from horizontal to vertical trim. 56 S&F of 2 way Powder coated Connectors Cover shall be of 1.5mm thick aluminium/PVC die Cast for 45mm Profile Cover. 57 S&F of 1 way Powder coated End Connectors Cover shall be made of 1.5mm thick Aluminium/PVC die Cast for 45mm Profile Cover. 58 S&F of Keyboard tray channel base 300mm (L) made of CRCA Sheet 1.1 mm thick zinc plated. 59 S&F of Keyboard Tray top made of 25mm thick top dual side 0.8mm Laminate board size 500X350mm. 60 S&F of Worktop made of 25mm thick dual side 0.8mm Laminate board with 2mm thick PVC beading size 600X900mm& Laminate colour code – Oxford Cherry as per site. 61 S&F of Side panel made of 12mm thick dual side 0.8mm Laminate board size 600X600mm. 62 S&F of Front panel made of 12mm thick dual side 0.8mm Laminate board size 600X900mm. 63 S&F of Footrest top made of 18mm thick dual side 0.8mm Laminate board size 150X900mm. 64 S&F of Glass with frosted design as per site 5mm thick size of 300X560mm. 65 S&F of Glass with frosted design as per site 5mm thick size of 300X860mm. 66 S&F of Accessories –Wire Manager Cap 67 S&F of Accessories –Level adjuster for Panel & Worktop 68 Tightening of complete modular work station by suitable size nails & screw as directed by Engr-in-Charge on site. 69 Almirah steel med (FD 67/1032) 70 S & F Lock 7 lever with duplicate keys components of Almirah steel medincluding dismantling unservicable one all as specified and as directed(Make of Lock- Harrison/Reena/Link) 71 S & F Handle 100 mm size chromium plated Heavy components of Almirah steel medincluding dismantling unservicable one all as specified and as directed. 72 S & F 3 way locking devicewith necessary fittings and painted with one coat of synthetic enamel paint of approved shade & quality over a coat of primer. 73 S & F leg made of 1mm thick CRCA sheetduly welded/riveted and painted with one coat of synthetic emamel paint of approved shade & quality over a coat of primer. 74 S & F door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with 7 leverlock with duplicate keys- 01 No,key hole and painting with one coat of synthetic enamel paint of directed shade by Engr-in-Charge over a coat of primerinside and outside Two coat of spray painting of Hammertonepaint (pattern of hammer tone shall be 0.06 gram silicon/kg) shall apply after preparation of surface all as specified and shown on drawing.Note for steel painting;- All steel surface shall be done with spray painting)(Make of Lock- Harrison) 75 S & F shelves made of 1mm thick CRCA sheetwelded/riveted and painted with one coat of synthetic emamel paint of directed shade by Engr-in-Charge over a coat of primer. 76 M&L for Preparation of old paintedinner steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of synthetic enamel paint (spray painting) of approved quality including dents/bends all as specified and as directed.Note: Paint shall be make of Asian/BerEngr-in-Charger/Shalimar and shade of colour as per direction of Engr-in-Charge. 77 M&L for Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) of approved qualityincluding dents/bends all as specified and as directed.Note Paint shall be make of Cosmos/MRFVapcoure and shade of colour as per direction of Engr-in-Charge. 78 Chair steel tubular with/ without arms (FD-75 M) 79 S & F ofsuitable size new synthetic foam of 75mm thick with 32 density for seat duly coverd with synthteictepastry/leatheratte raxine of approved shade and quality fitted on 12 mm BWR Plywooodin lieu of oldSeat frame of Chair steel tubular with/ without Hnadle fixed with screws 4 Nos and nuts to the chair frame alongwith MS flat (whereever required)complete all as per drawing. including dismantling unservicable one all as specified and as directed. 80 S & F ofsuitable size new synthetic foam of 75mm thick with 32 density for Back duly coverd with synthteic tepastry/leatheratte raxine of approved shade and quality fitted on 12 mm BWR Plywooodin lieu of oldSeat frame of Chair steel tubular with/ without Hnadle fixed with screws 4 Nos and nuts to the chair frame alongwith MS flat (whereever required)complete all as per drawing. including dismantling unservicable one all as specified and as directed. 81 S & FHandle made of Teak wood dulypainted with two coats of synthetic enamel paint of approved shade and quality and fixed to the chair tubular with arms with screws of suitable size complete all as per drawing including dismantling unservicable one all as specified and as directed. 82 S & F MS Flatsize 25 x 25 x 4mm thick welded/Screwed at four corner at bottom of the seat only to supportand screwed with the seat at two places complete all as per drawing. including dismantling unservicable one all as specified and as directed. 83 M&L for preparation of sufaces and painting with synthetic enamel paint BL Greay colour/apporoved shade to chair steel tubular with without arms including 04 Nos of PVC bushes to the bottom of the chair frame and 02 Nos of PVC caps on the top of the frame complete all as specified and directed. 84 Almirah small steel (FD 67) FD-243 85 S & F Lock 7 lever with duplicate keys components of Almirah steel medincluding dismantling unservicable one all as specified and as directed(Make of Lock- Harrison//Link) 86 S & F mild steel Handle 100 mm size chromium plated Heavy components of Almirah steel medincluding dismantling unservicable one all as specified and as directed. 87 S & F 3 way locking devicewith necessary fittings and painted with one coat of synthetic enamel paint of approved shade & quality over a coat of primer. 88 S & F leg made of 1mm thick CRCA sheetduly welded/riveted and painted with one coat of synthetic emamel paint of approved shade & quality over a coat of zinc primer. 89 S & F door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with 7 leverlock with duplicate keys- 01 No,key hole and painting with one coat of synthetic enamel paint of directed shade by Engr-in-Charge over a coat of primerinside and outside Two coat of spray painting of Hammertonepaint (pattern of hammer tone shall be 0.06 gram silicon/kg) shall apply after preparation of surface all as specified and shown on drawing.Note for steel painting;- All steel surface shall be done with spray painting) as per satisfaction of engr-in-charge/GE.(Make of Lock- Harrison) 90 S & F shelves made of 1mm thick CRCA sheetwelded/riveted and painted with one coat of synthetic emamel paint of directed shade by Engr-in-Charge over a coat of primer. 91 M&L for Preparation of old paintedinner steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of synthetic enamel paint (spray painting) of approved quality including dents/bends all as specified and as directed.Note: Paint shall be make of Asian/BerEngr-in-Charger/Shalimar and shade of colour as per direction of Engr-in-Charge. 92 M&L for Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) of approved qualityincluding dents/bends all as specified and as directed.Note Paint shall be make of Cosmos/MRFVapcoure and shade of colour as per direction of Engr-in-Charge. 93 Almirah steel med 1/2 Hanging ,1/2 Shelves (FD 1034) 94 S & F Lock 7 lever with duplicate keys components of Almirah steel medincluding dismantling unservicable one all as specified and as directed(Make of Lock- Harrison/Reena/Link) 95 S & F M.S Handle 100 mm size chromium plated Heavy components of Almirah steel medincluding dismantling unservicable one all as specified and as directed. 96 S & F 3 way locking devicewith necessary fittings and painted with one coat of synthetic enamel paint of approved shade & quality over a coat of primer. 97 S & F leg made of 1mm thick CRCA sheetduly welded/riveted and painted with one coat of synthetic emamel paint of approved shade & quality over a coat of primer. 98 S & F door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with 7 leverlock with duplicate keys- 01 No,key hole and painting with one coat of synthetic enamel paint of directed shade by Engr-in-Charge over a coat of primerinside and outside Two coat of spray painting of Hammertonepaint (pattern of hammer tone shall be 0.06 gram silicon/kg) shall apply after preparation of surface all as specified and shown on drawing.Note for steel painting;- All steel surface shall be done with spray painting) of paints as approved by GE.(Make of Lock- Harrison) 99 M&L for Preparation of old paintedinner steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of synthetic enamel paint (spray painting) of approved quality including dents/bends all as specified and as directed.Note: Paint shall be make of Asian/BerEngr-in-Charger/Shalimar and shade of colour as per direction of Engr-in-Charge. 100 M&L for Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) of approved qualityincluding dents/bends all as specified and as directed.Note Paint shall be make of Cosmos/MRFVapcoure and shade of colour as per direction of Engr-in-Charge. 101 Renewal of following unserviceable parts of Almirah glazed steel with suitable new parts of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge. FD104(M) 102 S&F New lock of 6 lever with duplicate key of approved quality and make.(Make: Godrej/Harrison/Link/Lico) 103 S&F new shelves made out of 1.00 mm thick MS sheet fixed and welded where required. 104 S&F new mild steel Chromium Plated handles complete with nut and bolt as approved by GE. 105 S&F new M.S hinges (75mm) medium weight. 106 S&F of new legs made out of 1.00 mm thick MS sheet to match the original as shown on drg and directed by Engr-In-Charge. 107 S&F of suitable pattern MS clamps for holding of almirah shelves. 108 S&F of new glasses of existing shape & size as shown on drg and directed by Engr-In-Charge. 109 S&F new bush (chakri) of suitable pattern for the locking system. 110 S&F new locking device with plunger rod of suitable pattern to the locking system of Almirah steel. 111 M&L for Preparation of old paintedinner steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of synthetic enamel paint (spray painting) of approved quality including dents/bends all as specified and as directed.Note: Paint shall be make of Asian/BerEngr-in-Charger/Shalimar and shade of colour as per direction of Engr-in-Charge. 112 M&L for Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) of approved qualityincluding dents/bends all as specified and as directed.Note Paint shall be make of Cosmos/MRFVapcoure and shade of colour as per direction of Engr-in-Charge. 113 Renewal of following unserviceable parts of Book Case glass front steel with suitable new parts of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge.FD-90(m) FD-1028 114 S&F New lock of 4 lever (set of 4 lock) with duplicate key of approved quality. (Make: Godrej/Harrison/Link/Lico) 115 S&F new CP handles complete with nut and bolt of standard size. 116 Repair of u/s sliding shutter as shown on drgs 117 S&F of new glasses of 4mm thick best quality ISI marked as specified & directed. 118 M&L for Preparation of old paintedinner steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of synthetic enamel paint (spray painting) of approved quality including dents/bends all as specified and as directed.Note: Paint shall be make of Asian/BerEngr-in-Charger/Shalimar and shade of colour as per direction of Engr-in-Charge. 119 M&L for Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) of approved qualityincluding dents/bends all as specified and as directed.Note Paint shall be make of Cosmos/MRFVapcoure and shade of colour as per direction of Engr-in-Charge. 120 Locker Bed Side Steel (FD-1029, FD-257) 121 S & F Hasp and Staple of 100 mm size chromium plated Heavy components of Locker steelincluding dismantling unservicable one all as specified and as directed. 122 S & F Hasp & stapplechromium plated components of Locker steelincluding dismantling unservicable one all as specified and as directed. 123 S & F leg made of 1mm thick CRCA sheetduly welded/riveted and painted with one coat of synthetic emamel paint of approved shade & qualityover a coat of primer. 124 S & F door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size, Haps and Staple of approved quality, painting with one coat of synthetic enamel paint shade as directed by Engr-in-Charge over a coat of primerinside and outside and Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) shall be applied after preparation of surface all as specified and shown on drawing.Note:- All steel surface shall be done with spray painting with paint as approved.Make of Lock- Harrison/Rina/Link 125 Removing the existing worn out side holder with 20mm dia aluminium conduit pipe of locker bed side steel and S & F new side holder with 20mm alluminium conduit pipe as per existing.Shape and size shown on drawing all as specified and directed by Engr-in-Charge.Drg No FD-1029 126 Removing the existing unserviceable legs & providing & fixing new legs made out of 1mm thick MS black sheet duly painted with Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) shall after preparation of surface all as specified and shown on drawing directed by Engr-in-Charge. 127 M&L for Preparation of old paintedinner steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of synthetic enamel paint (spray painting) of approved quality including dents/bends all as specified and as directed.Note: Paint shall be make of Asian/BerEngr-in-Charger/Shalimar and shade of colour as per direction of Engr-in-Charge. 128 M&L for Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) of approved qualityincluding dents/bends all as specified and as directed.Note Paint shall be make of Cosmos/MRFVapcoure and shade of colour as per direction of Engr-in-Charge. 129 Locker Bed Side Steel( SKD-562) 130 Removing the existing unserviceable legs & providing & fixing new legs made out of 1mm thick MS black sheet duly painted with Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) shall after preparation of surface all as specified and shown on drawing directed by Engr-in-Charge.SKD-562 131 Removing theexisting unserviceable handle and S & F new handle chromium plated 100mm in Heavy patteren all as specified and directed by Engr-in-Charge.SKD-562 132 3 way locking devicewith necessary fittings and painted with one coat of synthetic enamel paint of approved shade & quality over a coat of primer. 133 Removing the existing worn out side holder and hangingconduit pipe of locker steel and S & F of new side holder and hanging conduit pipe as per existing shape and size shown on drawing and all as directed by Engr-in-Charge.SKD-562 134 Taking down old unserviceable existing lock of locker steel and S & Fnewlock 7 lever duplicate key all as specified and directed by Engr-in-Charge. SKD-562 135 Removing the existing unseviceable hingesand S & F new hinges mild steel medium weight duly welded as per existing shape and size all as specified and directed by Engr-in-Charge.SKD-562 136 S & Fdoor shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with 7 leverlock with duplicate keys- 01 No,key hole and painting with one coat of synthetic enamel paint of directed shade by Engr-in-Charge over a coat of primerinside. And outside Two coat of spray painting of Hammertonepaint ( pattern of hammertone shall be 0.06gr silicon/kg) Shall after preparation of surface complete all as specified and shown on drawing.Note :- All steel surface shall be done with spray painting and Make of Lock- Harrison 137 M&L for Preparation of old paintedinner steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of synthetic enamel paint (spray painting) of approved quality including dents/bends all as specified and as directed.Note: Paint shall be make of Asian/BerEngr-in-Charger/Shalimar and shade of colour as per direction of Engr-in-Charge. 138 M&L for Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying Two coat of spray painting of Hammertonepaint (pattern of hammertone shall be 0.06 gram silicon/kg) of approved qualityincluding removal of dents/bends all as specified and as directed.Note:-Paint shall be make of Cosmos/MRFVapcoure and shade of colour as approved by Engr-in-Charge. 139 Table 3X2 (900mmx600mm) Steel with/without drawar(FD-1008-1007). 140 Removing the existing unserviceable top of Table and S & F the same made of 18mm thick pre laminated MDFboard duly post forming laminates one side laminated finish rest all as specified and directed 141 S&F Drawer made of 1mm CRCA sheetincluding painting with synthetic enamel paint of approved shade & quality over a coat of primer both inside and outside including preparation of surfaces and repairing inter locking system and providing new lock 4 lever to drawerand dismenteling of unsv one. 142 Removing old unserviceable frame/Leg and S & F New Frame/leg of existing size, shape complete all as specified and shown on drg and directed by Engr-in-Chargeshape complete all as specified and shown on drg .All Joints duly welded/Screwed as per Drgs 143 M&L for Preparation of old painted steel sufaces by scraping with emery paper, cleaning, dusting and making the surfaces smooth and applying two coat of Olive green synthetic enamel paint including four Nos of hard rubber shoes. Paint should be Make of Asian/Shalimar/BerEngr-in-Charger approvedby Engr-in-Charge. 144 Table steel 3 x 1½ (900mm x 450mm) examination (covered with 1mm thick black sun mica) FD -GE/PN/F-4 145 Removing the existing unserviceable top of Table and S & F the top made of 18mm thick pre laminated MDFboard duly post forming laminates rest as specified and as directed. 146 Removing old unserviceable frame/Leg and S & F New Frame/leg of existing size, shape complete all as specified and shown on drg and directed by Engr-in-Chargeshape complete all as specified and shown on drg .All Joints duly welded/Screwed as per Drgs 147 M&L for Preparation of old painted steel sufaces by scraping with emery paper, cleaning, dusting and making the surfaces smooth and applying two coat of Olive green synthetic enamel paint including four Nos of hard rubber shoes. Paint should be Make of Asian/Shalimar/BerEngr-in-Charger approvedby Engr-in-Charge. 148 Renewal of following unserviceable parts of Form Without Back/Form with Back with suitable new parts of (teak wood) existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge.FD-77,FD 1027 149 S&F new Seat of first class hard wood teakduly polishedand fixed as per drg and directed. 150 S&F new Back of first class hard wood teakduly polishedand fixed as per drg and directed. 151 S & F new Seat Frame of Exesting size made from 1.5mm thick 25 mm M/S tube as exestingduly welded 152 S & F new Legs of Exesting size made from 1.5mm thick 25 mm M/S tube as exestingduly welded 153 Tightening of complete form without back by suitable size nails & screw as directed by Engr-in-Charge on site. 154 M&L for two or more coats of spray painting and walnutpolish on steel & wooden surface of form without back with high class finish, including necessary rubbing, denting and smoothness surfaces all as directed by Engr- in-charge. 155 Repair/Relacement of following u/s parts of Table dining to seat 18 persons (5850x1050mm) with suitable new parts (teak wood) of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge. (Set of three pieces) FD No. BZ/FD/01 156 S&F of legs as per drg and as directed. 157 S&F of long rail as per drg and as directed. 158 S&F of short rail as per drg and as directed. 159 S&F new top of prelaminated MDF board of18 mm thick size as per drg duly post forming lamination 160 Tightening of complete table by suitable size nails & wood corner as directed by Engr-in-Charge on site. 161 M&Loneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 162 Renewal of following u/s parts of Table dining to seat 28 persons (9100x1050mm) with suitable new parts (teak wood) of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge.(Set of four pieces)FD No. BZ/FD/01 163 S&F of legs as per drg and as directed. 164 S&F of long rail as per drg and as directed. 165 S&F of short rail as per drg and as directed. 166 S&F new top of prelaminated MDF board of18 mm thick size as per drg duly postforming lamination 167 Tightening of complete table by suitable size nails & wood corner as directed by Engr-in-Charge on site. 168 M&Loneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 169 Renewal of following unserviceable parts of Table dining to seat 32 persons(10400x1050mm) with suitable new parts (teak wood) of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge.(Set of five pieces) FD No. BZ/FD/01 170 S&F of legs as per drg and as directed. 171 S&F of long rail as per drg and as directed. 172 S&F of short rail as per drg and as directed. 173 S&F new top of prelaminated MDF board of18 mm thick size as per drg duly postforming lamination 174 Tightening of complete table by suitable size nails & wood corner as directed by Engr-in-Charge on site. 175 M&Loneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 176 Renewal of following unserviceable parts of Table dining to seat 36 persons(11700x1050mm) with suitable new parts (teak wood) of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge.(Set of five pieces) FD No. BZ/FD/01 177 S&F of legs as per drg and as directed. 178 S&F of long rail as per drg and as directed. 179 S&F of short rail as per drg and as directed. 180 S&F new top of prelaminated MDF board of18 mm thick size as per drg duly postforming lamination 181 Tightening of complete table by suitable size nails & wood corner as directed by Engr-in-Charge on site. 182 M&Loneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 183 Renewal of following u/s parts of Table dining to seat 50 persons (16250x1050mm) with suitable new parts (teak wood) of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge.(Set of seven pieces)FD No. BZ/FD/01 184 S&F of legs as per drg and as directed. 185 S&F of long rail as per drg and as directed. 186 S&F of short rail as per drg and as directed. 187 S&F new top of prelaminated MDF board of18 mm thick size as per drg duly postforming lamination 188 Tightening of complete table by suitable size nails & wood corner as directed by Engr-in-Charge on site. 189 M&Loneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 190 Renewal of following unserviceable parts of Table dining to seat 56 persons(18200x1050mm) with suitable new parts (teak wood) of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge. (Set of eight pieces) FD No. BZ/FD/01 191 S&F of legs as per drg and as directed. 192 S&F of long rail as per drg and as directed. 193 S&F of short rail as per drg and as directed. 194 S&F new top of prelaminated MDF board of18 mm thick size as per drg duly postforming lamination 195 Tightening of complete table by suitable size nails & wood corner as directed by Engr-in-Charge on site. 196 M&Loneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 197 Renewal of following u/s parts of Table dining to seat 80 persons(23637x1050mm) with suitable new parts (teak wood) of existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge. (Set of eleven pieces) FD No. BZ/FD/01 198 S&F of legs as per drg and as directed. 199 S&F of long rail as per drg and as directed. 200 S&F of short rail as per drg and as directed. 201 S&F new top of prelaminated MDF board of18 mm thick size as per drg duly postforming lamination 202 Tightening of complete table by suitable size nails & wood corner as directed by Engr-in-Charge on site. 203 M&Loneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 204 Teapoy Verandah FD-255, 205 Removing the existing unserviceable top of Table and S & F the same made of 18mm thick pre laminated MDFboard duly postforming, one side laminated finish rest all as specified and directed 206 Removing old unserviceable frame/Leg and S & F New Frame/leg of existing size, shape complete all as specified and shown on drg and directed by Engr-in-Chargeshape complete all as specified and shown on drg .All Joints duly welded/Screwed as per Drgs 207 M&L for Preparation of old painted steel sufaces by scraping with emery paper, cleaning, dusting and making the surfaces smooth and applying two coat ofapproved shadesynthetic enamel paint including four Nos of hard rubber shoes. Paint should be Make of Asian/Shalimar/BerEngr-in-Charger approvedby Engr-in-Charge. 208 Table dinning Steel 900x900x760mm 209 Removing the existing unserviceable top of Table and S & F the same made of 18mm thick pre laminated MDFboard duly postforming, one side laminated finish rest all as specified and directed 210 Removing old unserviceable frame/Leg and S & F New Frame/leg of existing size, shape complete all as specified and shown on drg and directed by Engr-in-Chargeshape complete all as specified and shown on drg .All Joints duly welded/Screwed as per Drgs 211 M&L for Preparation of old painted steel sufaces by scraping with emery paper, cleaning, dusting and making the surfaces smooth and applying two coat of Olive green synthetic enamel paint including four Nos of hard rubber shoes. Paint should be Make of Asian/Shalimar/BerEngr-in-Charger approvedby Engr-in-Charge. 212 Table steel computer 1220x610x750 213 S&F new top of 18mm thick prelaminated MDF board duly postforming laminated of exesting size 214 S&F new side plank of 18mm thick prelaminated MDF board as shown on drg. 215 S&F new keypad tray of 18mm thick prelaminated MDF board including beading. 216 S&F of new heavy duty mild steel ball bearing slides/telecscopic channel for smooth functioning of key board drawer as approved by GE. 217 S&F of new bottom shelf of 18mm thick pre- laminated MDF duly postforming laminated of exesting size 218 S&F of new hard rubber shoes (black) 219 Tightening of complete table by suitable size nails & screw as directed by Engr-in-Charge on site. 220 M&L for two or more coats synthetic enamel BL Gray paint on steel frame surface with high class finish including necessary rubbing, denting, welding and smoothness surfaces all as directed by Engr- in- charge. 221 Rack steel large6 TierFD-129(M)/1038 222 S & F following components of Rack steel 6 tier including dismantling unservicable one all as specified and as directed. MS angle iron of size 30 x 30 x 3mm thick, 1905mm long including painting with one coat of synthetic enamel paint od approved shade & quality over a coat of primer. 223 Shelves of size 760 x 915mm made of 1mm CRCA sheet including painting with one coat of synthetic enamel paint of approved shade & quality over a coat of primer. 224 M&L for Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying one coat or more coat of synthetic enamel paint of approved shade & quality both inside and outside complete all as specified and as directed 225 Book Shelf Open Steel Small /Large ( FD 69) 226 S & F following components of Book Shelf Open Steel Large and Smallincluding dismantling unservicable one all as specified and as directed. MS angle iron of size 30 x 30 x 3mm thick, 1905mm long including painting with one coat of synthetic enamel paint of approved shade & quality over a coat of primer. 227 Shelves of size 760 x 915mm made of 1mm CRCA sheet including painting with one coat of synthetic enamel paint of approved shade & quality over a coat of primer. 228 M&L for Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying one coat or more coat of synthetic enamel paint of approved shade & quality both inside and outside complete all as specified and as directed for Book Shelf Open Large 229 M&L for Preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying one coat or more coat of synthetic enamel paint of approved shade & quality both inside and outside complete all as specified and as directed for Book Shelf Open Small 230 Desk FD -1021 231 S&F new top Box of Deskof 18mm thick prelaminated MDF board duly all joints shall be coverd with PVC Tape fix with adhesive of exesting size and dismenteling the UNSV one as directed and shown on drg . 232 S&F new M/S Tube of 25 mm 1.5mm thick of leg/stiffener/rails dismenteling the UNSV oneof 18mm thick prelaminated MDF board as shown on drg. 233 Tightening of complete table by suitable size nails & screw as directed by Engr-in-Charge on site. 234 S&F new rubber shoes . 235 M&L for two or more coats synthetic enamel BL Greay paint on steel frame surface with high class finish including necessary rubbing, denting, welding and smoothness surfaces all as directed by engr in charge. 236 Student revolving chair without hand rest(TP) 237 S&Fsuitable new 12 mm thick hot pressed plywoodcomplete to match the originalseat as shown on drg of approved make. 238 S&F suitable new fabric & moulded polyurethane foam of 50mm thick with 32 density for seat. 239 S&Fsuitable new tapestry cloth/leatherite rexine (cloth/rexine shall not be less than 350/- per RM) alongwith PVC lipping all round the seat fixing as exesting 240 S&Fsuitable new 12 mm thick hot pressed plywood for back as shown on drg. 241 S&F suitable new fabric & moulded polyurethane foam of 50mm thick with 32 density for back. 242 S&Fsuitable new tapestry cloth/leatherite rexine (cloth/rexine shall not be less than 300/- per RM) alongwith PVC lipping all round the back. 243 S&F suitable hydraulic system with droplift mechanism of backrest adjustedas per existing shape & size. 244 S&F suitable MS bearing of existing shape & size of various type chair revolving steel. 245 S&F new wheeled 4/5 prong base of existing shape & sizewith nut & bolts to chair revolving steel of various types. 246 S&F suitable caster wheels of existing shape & size with nut & bolts. 247 M&L for Two or more coat painting of synthetic enamel paint on frame of Chair computerwith high class finishing including necessary welding and smoothness of surface. 248 Repairs of Office chairs for work stations of Trade pattern 249 S&F suitable hydraulic system with droplift mechanism of backrest adjustedas per existing shape & size. 250 S&F suitable MS bearing of existing shape & size of various type chair revolving steel. 251 S&F new wheeled 4/5 prong base of existing shape & sizewith nut & bolts to chair revolving steel of various types. 252 S&F suitable caster wheels of existing shape & size with nut & bolts. 253 Charpoy OR steel FD- 220R 254 Removing old unserviceable plywood of double sleeping bunk/charpoy and S & F newmarine plywoodof12 mm thick BWR grade in both frame, ISI marked, Make: Archid ply/ century ply/ Green plyincluding fixing in position all as shown on drg with suitable size screws & cup washers all as specified and shown on drg and directed by Engineer-in-Charge 255 Removing old unserviceable long rail and S & F new Long Rail of existing size, shape all as specified and shown on drg with All Joints duly welded/screwed as per Drgs complete directed by Engineer-in-Charge 256 Removing old unserviceable Short Rail rail and S & F new Short Rail of existing sizeshape all as specified and shown on drgwith All Joints duly welded/screwed as per Drgs complete directed by Engineer -in- Charge 257 Removing old unserviceable Legs and S & F legs converstion from Short Rail item No. 34.02 of existing sizeshape all as specified and shown on drgwith All Joints duly welded/screwed as per Drgs complete directed by Engineer-in-Charge 258 Preparation of old painted outer steel sufaces by scraping with emary paper, cleaning, dusting and applying Two coat of spray painting of approved shade of approved quality paint 259 Display Board (2400 x 1200mm) 260 S&F of new Green Blazer Cloth of approved quality for Display Board 2400 x 1200mm and dismentling the UNSV one 261 M&Loneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 262 S&F of uphlostray of aprroved quality and shade and letheratte raxineof Sofa Set double Seat(TP), Sofa Set Single Seat(TP) , Sofa Set 2 Seater SK-577 Sofa set 05 Seater make of Godrej including minor surface reparing whereverey required and polishing with lacquer polish for smoothness of surface as exesting and directed by Engr-in-charge. 263 Renewal of following U/S parts of Wodden Bench & Desk (TP) with suitable new parts of (teak wood) existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge 264 S&F new Seat/Back top of Teak wood as exesting 265 Stiffeners (foot rest) 266 Buffers 267 Tightening of complete table by suitable size nails made of bamboo & wood corner(whereever required) as directed by Engr-in-Charge on site. 268 M&Lfor oneor more coat walnut wooden polish of approved shade and quality and one coat of lacquer polish for smooth shining and finish (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 269 Renewalof following unserviceable parts of Table Executive 6X3.5 with Side Cabinet/Drawer suitable new parts (MDF Board of IS Grade 12406 teak finish as match with exestingof existing shape & sizecomplete to match the original .(Different makes and pattern of Table Executive. 270 S&F Side Planks (builtin legs) 271 Top of Table executive as exesting 6X3.5 272 Drawer of Cabinet with Telescoipic chaneel and Knob/handle 273 Tightening of complete table by suitable size nails/Clamps & wood corner as directed by Engr-in-Charge on site. 274 Rack shoe steel (FD/E6/Map/02 (R). 275 S&F new wire mesh of 3 mm of duly wleded/fittedin tube frame of rack shoes steel . 276 Change of tubler frame of exesting size and replace the exesting one 277 Rubber Shoes 278 Spray Painting two or more coats of synthetic enamel of black shade paint on old painted surface 279 Renewal of following unserviceable parts of Bed Hard with ply top with suitable new parts of (teak wood) existing shape & size complete to match the original as shown on drgand directed by Engr-In-Charge.FD-21, 246, 247, SK- 280 S&F 04 mm thick both side teak face ply all over the head restof bed including teak wood beading. 281 S&F 04 mm thick both side teak face ply all over the foot rest of bed including teak wood beading . 282 Removing old unserviceable head board and supply & fixing new head board made out of Istclass hard wood (Sisham/teak) frame including 4 mm thick one side teak face ply ISI markedfor both sides and complete teak wood beading shall be provided all around as per drg. Exposed to view wooden, ply surfaces shall be french polished with high class glossy finish. Note:-Playwood shall be make of Archid Ply/Green Ply/Century Ply 283 Removing old unserviceable foot board and supply and fixing new foot board made out of Ist class hard wood (Sisham/teak) frame including 4 mm thick one side teak face ply ISI marked for both sides and complete 4mm thick teak wood beading shall be all around provided as per drg. Exposed to view wooden, ply surfaces shall be french polished with high class glossy finish. Note Playwood shall be make of Archid Ply/Green Ply/Century Ply 284 S&F new long rail made out of teak wood size1800x90x35mm as per drg and directedby Engr in charge. 285 S&F new short rail/center stiffner made out of teak wood size 900x90x35mmas per drg . 286 S&F new clamps for holding of MNF setas per drg and directedby Engr in charge. 287 S&F new 12mm thick BWR phenol bonded commercial plywood of size 1800x900mm , fitted with suitable nut & bolt complete to match the existing shape and size. 288 Tightening of complete bed by suitable size nails & wood corner as directed by Engr-in-Charge on site. 289 M&Lfor two or more coat Lacquer polish with high class finishing (after rubbing/scrapping and filling) to complete side as per existing shape and size in drg as directed by Engr-in- charge. 290 M&L for Spray Painting two or more coats of synthetic enamel of approved shade paint on old painted surface to under mentioned items of steel furniture with high class finishing including necessary scrapping, denting ,welding and smoothness surfaces as shown on drg and directed by Engr-in-charge. 291 Chair CBA special with hand rest.FD-260 292 Ladder for loft.FD-44, 238 293 Desk stand lecture steel FD-1022 294 Locker sixdoorsteel TP 295 Metal shelving Rack adjustable type small FD-69 (M) 296 Metal shelving rack adjustable type large FD-69 (M) 297 MNF frame all type FD-220, 246, 247 298 Rack side steel with four tray FD-97(M), 1023 299 Rack adjustable six tiers FD-106(M)1038 300 Stool steel size 305x305x510mm FD-81(M) 301 Steel Cup board TP 302 Table steel General Tubular TP 303 Trestle store room Iron FD-1043 304 Waste paper basket steel GE/PN/F-16
