Tender For PROVIDING TICKET COUNTER AT THAMARAYUR SASTHA TEMPLE -- 1 2.6.1Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavatedearth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds ofsoil 2 10.1Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer all complete. 3 50.10.2Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc.complete 4 4.1.3Providing and laying in position cement concrete of specified grade excluding the cost of centering andshuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mmnominal size) 5 21.1.1.2Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS :733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereverrequired including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium(minimum thickness of powder coating 50 micron) 6 21.1.2.2For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and makingprovision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasketrequired (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powdercoating 50 micron) 7 21.3.2Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50mm thickness 8 21.3.3Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDMrubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness 9 13.61.1Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two ormore coats on new work 10 12.50Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation asapproved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 gramsper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet andpolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum toavoid scratches during transportation and should be supplied in single length upto 12 metre or as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost purlins, rafters and trusses and including cutting to size and shape wherever required 11 12.51.1Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) totalcoated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinccoating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on bothside of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screwscomplete:Ridges plain (500-600 mm) 12 od150173/2024_2025Providing and fixing flat pressed 12 mm thick PF grade Diamond Chequred Plywood , backing orstudding with screws etc. complete ( Frames, backing or studding to be paid separately): 12mm thick 13 od150174/2024_2025Providing and fixing 4 mm thick ACP or equivalent make paneling 12 mm thick, to frame, backing orstudding with screws etc. complete ( Frames, backing or studding to be paid separately) as per thedirection of site Engineer-in-charge 14 50.12.4.1Providing and fixing false ceiling with 7.5 mm thick PVC plain panel board ceiling of approved quality inaluminium frame work with necessary screws etc complete (aluminium frame work shall be paidseparately) 15 21.5Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron)consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceilingincluding aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminiumperimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing theframe work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws allcomplete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjustinghangers, ceiling cleats and expansion hold fasteners to be paid for separately ). 16 21.6Providing and fixing 6 mm dia. G I level adjusting hangers ( upto 1200 mm length), fixed to roof slabs by means of ceiling cleats made out of G.I flat 40x3 mm size 60 mm long and stainless steel expandabledash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer -in-Charge. 17 21.17Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.(Only weight of grill to be measured for payment ). 18 od150175/2024_2025Providing and fixing 710 BWP Marine plywood 19 mm thick or equivalent make in shelves with screwsand fittings wherever required, edges to be painted with polyurethene primer (fittings to be paidseparately) as per the direction of site Engineer -in-charge 19 od150176/2024_2025Supplying and fixing laminated sheet on plywood 20 od150178/2024_2025Supplying and fixing fiber Mughappu with ornamental finish 21 od150179/2024_2025Supplying and Fixing Fibre Eave Board 22 od150181/2024_2025Supply and Fixing Stainless Steel Automatic Hinges 2 x 2 23 21.16.2Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete asper direction of Engineer-in-Charge.Powder coated minimum thickness 50 micron aluminium 24 od150183/2024_2025Supplying and Fixing Cupboard Lock 25 9.97.5Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC10 as per : 1868), transparent or dyed to required colour or shade, with necessary screwscomplete:100x10 mm
