|
| 1 | Supply & fixing Cat 6 UTP jack with strain relief and bend limiting boot as required including polycarbonate modular type shuttered face plate, RJ-45 Data jack including GI /PVC box alongwith modular base & cover plate for modular switches in recess/ surface etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. |
| 2 | Supplying and drawing of UTP 4 pair CAT 6A LAN Cable in theexisting surface/ recessed Steel/ PVC conduit as required. |
| 3 | 1 run of cable |
| 4 | Supply and fixing in of IPBAX |
| 5 | Supply of IP Phones |
| 6 | Supply & fixing of single partition (two-tier) 105 mm x 50 mm DLP U-PVC Trucking with all accessories including necessary cutting, fixing & finishing the same, placing in position, etc. as required. Make: Legrand or eqv) |
| 7 | 22 U Rack with Cable manager, Tray 6 Socket PDU, Ex-Fans etc. Side openable door plus front site glass door and locking system as required (Make-Valrack /Comrack or Eqv.) |
| 8 | 24 port patch panel fully loaded Cat6 as required. (Make- D-link, Molex, Avaya). |
| 9 | LIU patch panel for optical fiber interconnecting unit as required. (Make- D-link, Molex, Avaya). |
| 10 | Making indoor type LAN OFC cable end termination of 6 core Optical Fiber Cable as required |
| 11 | Supply & Erecting FR grade, PVC armoured multimode / singlemode Optical Fibre Cable with 6 fibres, with core Dia 50 um, suitable for 1 GBps ethemet distence at 850nm of wavelength, on wall/ ceiling or laid in theexisting surface/ recessed Steel/ PVC conduit as required.(Make- D-Link, Finolex, Molex) |
| 12 | Supply, Erecting & testing of CAT6 Patch Cord as required. (Make- D-link, Molex,Avaya) |
| 13 | Supply, Installation, Testing and commissioning of 48 Port Network Switch complete as required. Make: Cisco |
| 14 | Supply, Erecting & testing of Fibre Patch Cord with Fibre Module as required. Make: Cisco |
| 15 | Supply, Erecting & testing of Pigtel as required. (Make- D-link, Molex,Avaya) |
| 16 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including Dismantling as required. (Group C) |
| 17 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulatedcopper conductor single core cable etc. as required. (Group C) |
| 18 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copperconductor single core cable in Surface/ recessed PVC conduit,and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. (Group C) |
| 19 | Supply and fixing of recessedmounting LEDdown lighter of1to3Weachassembledonsingle MCPCB,havingcolortemp 4000K TO 6500K&having25000 to50000 burning hrs life with minimum @ L 80, system lumen output should be minimum with efficacy>80lm/W. LED driver, PF 0.90. The colour rendering index of LED light should be more than 70. Housing made CRCA powder coated frame with glare freediffused polycarbonate cover. Submission LM 80-08 Form LED Source Manufacturer & LM79-08/IS16106 fromNABLapprovedlab. Manufacturer manadatoryi/cconnection wire, testing etc. tocompletethejob.1YrsGuaranteecertificatefrom manufacturer. |
| 20 | Recessed slim LED square downlighter\", 9W, 4-6.5K, Make: Wipro Model No. LD96-101-XXX-60-XX or equivalent in Philips, Crompton Greaves, Bajaj, Jaquar, havells etc. |
| 21 | Supply, Installation, Testing and commissioning of Energy efficient recessed mounted LED luminaire suitable for 2x2 grid ceiling complete with driver etc as required. Make: Wipro Model No.CRCO10R036HP57G2 or equivalent in Philips, Crompton Greaves, Bajaj, Jaquar, havells etc. |
| 22 | Led luminiare 2\" X 2\", 36W, 4-6.5K, Model No. CRCO10R036HP57G2 or equivalent |
| 23 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 24 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 25 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 26 | 4 x 10 sq. mm + 2 x 10 sq.mm |
| 27 | 4 x 16 sq. mm + 2 x 16 sq.mm |
| 28 | Supplying and fixing 250 mm x 250 mm x50mm deep GI finish. The junction boxes shall have knock-outs on all sides suitable for Raceways/conduits. WithGI Plate The knock out shall be removed at site as per requirements. |
| 29 | Supply and Installation of 75X50mm GI Raceway with GI cover and other accessories under flooring |
| 30 | Supplying & fixing of 3 Nos. 6Amp modular socket (shuttered) outlet Controlled by 1 No. 1 way single pole 16/15 amps modular type switch, polycarbonate white cover plate andearthing the 3rd pin painting etc. as required. |
| 31 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 32 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 33 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 34 | 25 mm |
| 35 | 32 mm |
| 36 | Supplying and fixing of following ways surface/ recessmounting, vertical type, 415 V, TPN MCB distribution board ofsheet steel, dust protected, duly powder painted, inclusive of200 A tinned copper bus bar, common neutral link, earth bar,din bar for mounting MCBs (but without MCBs and incomer ) asrequired . (Note : Vertical type MCB TPDB is normally usedwhere 3 phase outlets are required.) |
| 37 | 12 way (4 + 36), Double door |
| 38 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 39 | Single pole |
| 40 | Triple pole |
| 41 | Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 42 | 63 A |
| 43 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 44 | Supply, installation testing, commissioning of 10 kva (Three Phase -IN Single Phase- OUT) ON-LINE Smart UPS System including parallel kit with Simple Network Management Protocol ( SNMP card ) along with sealed lead acid batteries (Maintenance free) suitable for 30 minnuts backup facility on full load with racks & connectors (including suitable size copper cable connection between ups ,battery bank and input power of UPS enlcuding MCCB or RCCB) complete with battery rack required One year warranty for ups & two years for battery etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. |
| 45 | Supply , installation, testing and commissioning ofmodular type Variable Refrigerant Flow air cooled Side Discharge Outdoor units suitable for cooling, inverter type Scroll (R1) Compressor(s), microprocessor based Controller, top discharge type condensing unit(s) with R410A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V+/-10% or 220V+/-10% , 3 Phase or 1 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge.(Note :- Compressor should be Manufactured by OEM only) |
| 46 | 05 HP |
| 47 | VRF/VRV Indoor Floor Standing AC :-Supply, installation, testing and commissioning of Floor Standing type comprising of copper evaporator,electronicexpansionvalve,blower, motor, filter pad, with inbuilt drain pump including internal wiring, controls with cordless remote etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge.. (Single phase) |
| 48 | 4.0 TR |
| 49 | COPPER PIPING :- Supply installation testing commissioning of interconnecting copper refrigerant pipe work (19mm / 13mm thick ) duly insulated with elastomeric nitrile rubber type tubular insulation between indoor & outdoor units as per specifications. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. The piping shall be properly supported with 6mm full threaded rods over channel with Fasteners, Nuts & washer at 1m distance with firm supporting using PVC sleeve and cable tie. Extra support for Y-joints/Bends etc. to be given as per specifications. GI BOX type cable tray 100/150 mm wide for supporting refrigerant piping in shafts / terrace, complete with supports. (Min 1.2mm Thickness) C- Type Cover for cable tray, made out of 16 G GI sheet, to protect refrigerant pipe insulation on terrace. All piping shall be pressure tested for 1.5 times the working pressure. The quoted rates should be including of cost of GI BOX type cable tray 100/150 mm wide with covers. |
| 50 | 15.9 mm O.D.wall thickness >/= 0.8 mm(insulation – 13 mm thick) |
| 51 | 9.5 mm O.D. wall thickness >/= 0.8 mm (insulation – 13 mm thick) |
| 52 | REFRIGERANT :- Supply and additional refrigerant charge of Refrigerant R410 / 410A to compensate the additional piping done at site for all systems including testing commissioning as required, |
| 53 | OUTDOOR MS STAND |
| 54 | Drain Piping :- Providing and fixing of CPVC, 6Kg/cm2 drain water piping with fittings, support and insulated with 6 mmthickclosed cell elastomeric nitile rubberinsulation complete as per specification. |
| 55 | 25 mm dia ID |
| 56 | 2Cx 1.5 Sq. mm shielded cable or screened cable for communication (witin Pvc suitable size of conduit ) |
| 57 | Supply, installation, testing & commissioning of 1.5 TR, 5 Star, inverter based Split type Air-conditioning units each having Outdoor unit comprising of Rotary/Swing compressor, air-cooled condenser coil, condenser fan and Indoor unit comprising cooling coil, centrifugal blower, filters, controls including copper piping, drain piping MS mounted frame & vibration isolators as required and as the the approval of Engineer-in-charge. |
| 58 | Supply and laying ,testing &commissioning of Copper Earthing of 1 Core x 6 Sq mm |
| 59 | Supplying, installation, testing and commissioning ofWeather Proof (Minim. IP-65) Enclosure with25/32/40 Amp. 4PMCB + ELCB 300mA. rating 10kA for outdoor units complete as required. |
| 60 | Supply of 4 Core 16 Sqmm size of 1.1 KV grade mulit- core XLPE Armoured Aluminium Conductor Power cable conforming to IS 7098 (Part-1) / IS 1554 ( Part -1 )withupto dateamendments as required. (From Electrical Panel/MCBto ODUOutdoor Enclosure Box) |
| 61 | Supply of 4 Core 10 Sqmm size of 1.1 KV grade mulit- core XLPE Armoured Aluminium Conductor Power cable conforming to IS 7098 (Part-1) / IS 1554 ( Part -1 )withupto dateamendments as required. (From Electrical Panel/MCBto ODUOutdoor Enclosure Box) |
| 62 | Laying and fixing of one number PVC insulated and PVCsheathed / XLPE power cable of 1.1 KV grade of following sizeon cable tray/masonary duct as required. |
| 63 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 64 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. |
| 65 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. |
| 66 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colourTwo coats |
| 67 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in IIMI Campus lead or as directed by Engineerin-charge. |
| 68 | Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595 mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32 mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8 mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-chargeith 16 mm thick beveled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications |
| 69 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. |
| 70 | Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessaryfilling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge.. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) |
| 71 | Providing and fixing glazing in aluminium window, ventilator shutters and partitions etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. (Cost of aluminium snap beading shall be paid in basic item): With toughened glass panes of 5.0 mm thickness |
| 72 | Providing & Pasting Frosted Film of thickness 100 micron in required design all complete job as per the direction of Engineer-in-charge. |
| 73 | Providing and fixing H-handle for glass door of approved quality including necessary screws etc. complete as per the direction of Engineer-in-Charge |
| 74 | Providing and fixing patch lock for door of approved quality including necessary screws etc. completeas per the direction of Engineer-in-Charge. |
| 75 | Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings,etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. (Door handle, lock and stopper etc. to be paid separately) |
| 76 | Providing & fixing skylight at terrace level with multi cell/tight cell polycarbonate panel system 12mm thick of make danpalon or GE (minimum) confiring to specifications. Panel will be 12 mm thick (min.) single panel. The weight of the panel will be 2550 gram per square meter. panel width shall not be less than 900mm to ensure best performance for wind uplift, viration, oil canning and visual appearance palens shall be manufactured with vertical standind seam-locking mechanism to ensure maximum uplift capability etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. |
| 77 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. Hot finished seamless type tubes |
| 78 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets,gates and similar works etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. |
| 79 | Supply and Installation of Work station (4 seating each) having 750x1200mm each seating with lockable storage unit inside the workstation. Addition file Storage facility with locable arrangement for each side of workstation having minimum size 300x750x1200mmincluding hardware, minifixes etc. all complete as per the requirement of the site and direction of the Engineer-in-Charge. |
| 80 | SITC of Wi-Fi Router complete as required |
