|
| 1 | M&L for 25 mm thick cement concrete 1:2:4 type B-0(using 12.5 mm graded crushed stone aggregate) as in sunken floor finished even and smooth using extra cement with using water proofing compound as per manufacturer\"s instructions l complete all as specified and directed Note:- Water proofing compound shall be measured and paid seperately under respective item of Schedule \"A\"/BOQ. |
| 2 | M & L for providing plain cement concrete, type E-2, 1:5:10 (using 40 mm graded brick aggregate) as in sunken, filling and mass concretel complete all as specified and directed. |
| 3 | Applying epoxy treatment for bonding new or old concrete surfaces by applying chemical FOSROC and NITOBOND AR complete all as specified and as per manufacturer instructions complete all as specified and directed. |
| 4 | M & L for water proofing treatment as specified here-in-after, applying a priming coat of suitable primer over cleaned concrete surface, applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg/sqm, applying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced application and finally applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg/sqm over polymeric membrane complete all as specified and directed. |
| 5 | M&L for 12 mm thick cement plaster finishedwith a floating coat of neat cement of mix in 1:3 (1 cement: 3 fine sand) complete all as specified and directed. |
| 6 | M&L for non skid ceramic coloured jointfree tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including including laying of 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. |
| 7 | Srl item No. 6 above but on verticalsurfaces such as skirtingover and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tilescomplete all as specified and directed. |
| 8 | M&L for glazed ceramic coloured tiles of size 300 mm x 450 mm x 7mm /350 mm x 450 mm x 7mm /250 mm x 250 mm x 7mmthick as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match withover and including10 mm thick rendering in cement mortar 1:4 finished rough surface to receive tiles rubbish off the premises complete all as specified and directed. |
| 9 | Virified Ceramic tiles 10 mm thick light shade (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed inwhite or colour cement to match over and including 15 mm thick screed bed in CM 1:6complete all as specified and directed. |
| 10 | Srl item No 9 above but on verticalsurfaces such as skirtingover and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tilescomplete all as specified and directed. |
| 11 | M&L for Granite slab of 16 to 18 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and incl Demolition of stone slab and tileslaid bedded and pointed in anymortor of any description or thickness in floor complete all as specified and directed. |
| 12 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding0.06 . Sqm but not exceeding 0.11 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including laying of 15 mm thick screed bed or bedding layer in CM 1:6 completecomplete all as specified and directed. |
| 13 | Taking downcement or cement lime plaster of any description including racking out joints, hacking for keys , scrubing down with water etc, complete all as specified and directed. |
| 14 | M&L for Rendering 15 mm thick on fair faces of concrete/brick surfaces in cement mortar 1:4mixed withwater proofing compound as per manufacturer\"s instruction, finished fair and even without using extracement complete all as specified and directed. Note :- WPC shall be measured and paid forseprately as \"supply only\" under respective item of sch A/ BOQ. |
| 15 | M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extracement) complete all as specified and directed. |
| 16 | M & L for 10 mm thick rendering on fair faces of brick work or concrete surfaces of ceiling in cement mortar 1:3 finished even and smooth (without using extracement) complete all as specified and directed. |
| 17 | Supply only Liquid water proofing compound ISI Marked (used 200 ml per bag of cement) complete all as specified and directed. |
| 18 | M & L for preparation of newly plastered surface and applying of Birla/JK white wall putty approx 1 mm thick in two layeras per manufacturer\"s instruction on newly prepared surfaceand make the surface smooth by rubbing with sand papers etcand applying two coat of oil emulsion distemper over a coat of primer complete all as specified and directed. complete all as specified and directed. |
| 19 | Prepration of new plaster surfaces of ceiling and applying three coat of white wash complete all as specified and directed. |
| 20 | M & L Preparation of old surfaces of ceiling, plastered on un plastered by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss & efflorescent salts, removing all vegetation growth and trading oil and greasy spots and applying one coat of white wash on old white washed surfaces ofceiling complete all as specified and directed. |
| 21 | M&L for preparing old surfaces of walls plastered or un-plastered by brooming down with steelor wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary puttyand make the surface smooth by rubbing with sand papers etc andapplying one coat of distemper oil emulsion on old prepared surfaces of walls completeall as specified and directed. |
| 22 | M&L for complete removal of existing treatement by scraping, washing, rubbing down or stopping distempered or painted surfaces etcof walls plastered or un-plastered & removing all vegetation growth, cleaning & applying of Birla/JK white wall putty approx 1 mm thick in two layer as per manufacturer\"s instruction on existingprepared surface and make the surface smooth by rubbing with sand papers etcand applying two coats of oil emulsion distemper overa coat of alkali resistant primercomplete all as specified and directed. |
| 23 | M&L for Preparation of new plaster surfaces of wall and applying two coats of cement base paint etc complete all as specifed and directed. |
| 24 | M&L for preparation of old painted surface wall / ceiling by brooming down loose partical, removing of smoke soot, moulds and unwanted vegetation from wall, facia, parapet etc applying one coat of cement base paint complete all as specified and directed. |
| 25 | M&L for complete removel of existingplastered or unplastered surfaces on walls and applying of Birla/JK white wall putty approx 1 mm thickas per manufacturer\"s instruction on newly prepared surfaceand make the surface smooth by rubbing with sand papers etc andapplying Two coat ofweather proof exterior paint silicon basedover a coat of primercomplete all as specified and directed. |
| 26 | Taking down chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each including removing to store complete all as specified and directed. |
| 27 | Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 sqm and n. exc. 4.00 sqm each including removing to store complete all as specified and directed. |
| 28 | Taking down shutters of any descriptionexc 1 sqm & n. exc 2 sqmeach complete all as specified and directed. |
| 29 | Taking down shutterexc. 1 Sqm and n.exc 2 Sqm each and refixing the same opening after resecuring or easing and adjusting shutters of any description.complete all as specified and directed. |
| 30 | Taking down shutterexc.2 Sqm each and refixing the same opening after resecuring or easing and adjusting shutters of any description.complete all as specified and directed. |
| 31 | S&F powder coating anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 32 | S&F 35mm thick second classs hard woodplain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers,etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed. |
| 33 | S&F powder coating anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing not less then 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing , anodised aluminium snap, rubber packing , anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No), hinges type B-21 100 mm long (2 No) suitable handle (1 No) complete all as specified and directed. |
| 34 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames glazed with putty or fixed with beadsincluding punching or drilling out old glazing pins/spring clips etc complete all as specified and directed. |
| 35 | M&L for 5.5 mm thick sheet glass ordinary quality in panesexc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed. |
| 36 | S&F for 4 mm thick,Sheet glass,ordinary quality and glazing with beading (any type) or oil putty in square n exc0.5 sq. m in each pane, etc complete all as specified and directed. |
| 37 | S&F 4mm thick figured glass, pin head type and glazing with beading (any type) or oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed. |
| 38 | S&F for framed work such as grills, gratings, etc. With ends of bars shouldered and riveted, or forged into spikes, framed guard bars, barred iron doors ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con-forming to Fe. 290. Gde-E-165 with and including Dismantling wrought iron or mild steel work of any description not otherwise described complete all as specified and directed. |
| 39 | Providing and fixing pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed of size 105mm x 60mm complete all as specified and directed. |
| 40 | S&F factory made glazed and skelton shutters 35mm thick second class hard woodopen rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars, any numbers , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc; sizes of members of shutters as specified in SSR Part-I 2009 section 8, clause 8.24 (a)complete all as specified and directed. |
| 41 | S&F 35 mm thick Flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides complete all as specified and directed. |
| 42 | M&L 0.9mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer\"s instructions complete all as specified and directed. |
| 43 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wall plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 44 | Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on eitherside and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing in SSR Part II 2010 etc complete all as specified and directed. |
| 45 | S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized steel wire staples complete all as specified and directed. |
| 46 | S&F in repairgalvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized steel wire staples complete all as specified and directed. |
| 47 | M & L for preparation of new iron or steel surfaces of any description, over 10cm in width or girth,not applying two coats of synthetic enamel paint over a coat of Red oxide zince primer complete otherwise described complete all as specified and directed. |
| 48 | M & L for preparation of old iron or steel surfaces of any description, over 10cm in width or girth,not applying one coats of synthetic enamel paint complete otherwise described complete all as specified and directed. |
| 49 | S&F aluminium anodised barrel tower bolt of extruded section 200mm long and fixed complete all as specified and directed. |
| 50 | S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed complete all as specified and directed. |
| 51 | S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 52 | S&F 150mm size extruded aluminium alloy handles, fabricated type complete all as specified and directed. |
| 53 | S&F 125mm size extruded aluminium alloy handles, fabricated type complete all as specified and directed. |
| 54 | S&FButt hinges, medium weight coldrolled mild steel and fixed 100mm size complete all as specified and directed. |
| 55 | S&FButt hinges, medium weight coldrolled mild steel and fixed 75mm size complete all as specified and directed. |
| 56 | M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 57 | M&L for Preparation of old wooden surfaces over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed. |
| 58 | S&F in repair 18 to 20 mm thick solid PVC Board for cupboard/cabinet shutters with one side 1 mm thick printed PVC sheet other side plain PVC sheet of approved pattern as per specification and drawing and including necessary beading in matching colour, magnetic ball catcher, 1 brass 2 lever lock of 50 mm size complete all as specified and directed. |
| 59 | S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm completeall as specified and directed. |
| 60 | S&F in repair Chromium plated brass wall mixer 3-in-1 system fancy type with provision for both hand shower and overhead shower complete with wall Flange (without Hand & over head Shower) screwed down for 15 mm bore GI pipe complete all as specified and directed. |
| 61 | S&F in repair Chromium plated brass central hole Basin Mixer without Popup Waste system complete screwed down for 15 mm bore GI pipe complete all as specified and directed. |
| 62 | S&F in repair 15mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle chromium plated fancy type long shank and cup(concealed type), screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 63 | S&F in repair 125 mm size chromium plated brass shower rose with swivel joints and swivel arms for fixing with 15 mm pipe complete all as specified and directed. |
| 64 | S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic actiontype with inlet ball valve and float, handle with & including bracket andPVC flush pipe 32 mm borecomplete all as specified and directed |
| 65 | S&F in repair 125 mm size chromium plated brass shower rose with swivel joints and swivel arms for fixing with 15 mm pipe complete all as specified and directed. |
| 66 | S&F in repair bib cock long body with flange , fancy type,brass,chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule orGI socket complete all as specified and directed. |
| 67 | S&F in repair fancy typeangle cock with flange, 15 mm nominal bore, brass, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed. |
| 68 | S&F in repair 600x450 mm size and 5.5mm thick looking mirror, bevelled edge of selected quality glass with aluminium frame made of channel alround,mounted on 6 mm thick commercial ply or AC building board, fitted to wooden plug with CP screws.complete all as specified and directed |
| 69 | Providing and fixing sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass shelf with chromium plated bracket guard and railing as per sample approval complete all as specified and directed. |
| 70 | S&F in repair vitreous china wash hand basin (flat back) of size 550x400mmincluding one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector,MS brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed. |
| 71 | S&F in repair white vitreous China wash down water closet pan (pedestal) pattern, and trap(excluding) fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. with and including plastic water closet seat covers white closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device and 15mm dia chromium plated brass washing jet fixed to water closet with 15mm dia and 1.2m to 1.5m long flexible pipe with chromium plated spring type cover complete with fixing arrangement fancy look complete all as specified and directed. |
| 72 | S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet,integral foot rest (excluding flushing cistern and flush pipe) & including CI trap & connecting fitting as required set inplain cement concrete (1:3:6) type C-1and connecting to flusing cistern and trap & connecting fittings as required and making good to floor, complete all as specified and directed. |
| 73 | S & F in repair waste coupling 32 mm dia of PTMT (half or full threaded) minium weight 45 gram complete all as specified and directed. |
| 74 | S&F in repair Waste coupling to WHB/ kitchen and laboratory sink of 32/40 mm dia minium weight 75 gramcomplete all as specified and directed. |
| 75 | S&F in repair 15mm size PVC connections internally threaded with PVC washer,PTMT nuts of length 450mm complete all as specified and directed. |
| 76 | S&F in repair PVC Waste pipe to WHB/ kitchen sink of 32 mm diacomplete all as specified and directed. |
| 77 | S&F in repair drapery fancy type curtain rod shall be 32 mm dia of aluminium pipe with powder coating with wooden finish including bracket rings, fancy knob , curtai ring 08 Nos minimumincluding all fixing arrangement complete all as specified and directed. |
| 78 | S&F in repairsinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm with & including one waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement ,with PVC coupling, PVC waste pipe 40mm bore 750mm long complete all as specified and directed. Make as approved by GE. |
| 79 | S&F in repairs Stainless steel utencil plate rack size 600 mm x 600 mm x 250 mm ) using 0.8 mm thick sheet complete all as specified and directed. |
| 80 | S & F in repair tubular towel rail20mm dia 600mm long of brass chromimum plated complete all as specified and directed. |
| 81 | Taking out steel water tubing and connections including cleaning for refixing 15 mm dia complete all as specified and directed. |
| 82 | M&L for 15mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed. |
| 83 | Re-fixing old steel water tubing and connections in new or old position (walls, ceiling, floors etc) 15 mm dia complete all as specified and directed.(Note:Serviceable pipes & fiitings obtainedfrom item 82 to be re-used) |
| 84 | S&F in repair fancy type chromium plated health faucatwith1.50 metre longPVC tube coverCP flexible with wall hook suitable for 15 mm bore iron pipes or for unions and fixed complete all as specified and directed. Make-Prayag or other equivalent makes as approved by GE. |
| 85 | S&F in repairs 150mm dia chromium plated towel ringfixed with and including Chromium plated brass screws and cleats (Minimum weight 140gms) complete all as specified and directed. |
| 86 | S&F in repairs plastic water closet seat cover , whiteor tinted, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 87 | S&F door seal bottom, rubber shield, anti rust, brown colour black rubber including necessary screws etc., complete all as specified and directed. |
| 88 | M&L for PCC 1:2:4 Type B-1 {using 20mm graded crushed stone aggregate} as in coping/benching bed plates roof kerbs mud stops, including weathering, slightly rounded or chamfered angles and throating etc including necessary form work complete all as specified and directed. |
| 89 | S&F in repair floor door stopper double leg of aluminium alloy bodyof 140 mm length with aluminium base plate of size 50 mm x 40 mm complete all as specified & directed. |
| 90 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed. |
| 91 | Demolition of cement concrete (unreinforced) of any description as in ground floors and pavings not exceeding 15cm thickness (above or below ground floors) with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed.Notes for item No. 1 to 91:- (i) The work will be carried out upto 8th storey bldgs. Hence necessary complete scaffolding and other safety arrangements will be managed and made by tenderer/ Contractor accordingly at own expense. (ii) Tenderer kind attention is also invited to srl clause 1.16 of Sec-I on srl page No 1 to 91 (General rules for Safety in Construction) as specified in SSR Pt-I (2009) for safety measures/ precautions.(iii) Steel scaffolfing is to be used in the work. (iv) Necessary arrangement for temporary plug the / door / window / ventilator opening at time of taking down plaster/ new plaster till completion of work. Made by Tender / Contractor at own expense. |
