|
| 1 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil… |
| 2 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc |
| 3 | (A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by |
| 4 | Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 5 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 6 | (II) Cement concrete with 30 mm down graded shingles excluding shuttering.N.B. Variety |
| 7 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.(i) Pakur Variety |
| 8 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), |
| 9 | Brick work with 1st class bricks in cement mortar (1:4)(a) In foundation and plinth |
| 10 | 25 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 11 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with r |
| 12 | a) 25 mm to 30 mm thick wooden shuttering as per decision & direction ofEngineer-In-Charge. |
| 13 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing |
| 14 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back |
| 15 | B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & |
| 16 | M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, |
| 17 | Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook |
| 18 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface t |
| 19 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acry |
| 20 | a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc |
| 21 | SANITARY AND DRAINAGE WORKS,Page-107,Item-20(b)[M4] Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 |
| 22 | Supplying, Fitting & Fixing Factory made prelaminated P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm Prelaminated PVC sheet miter cut a |
| 23 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, |
| 24 | Labour for fitting and fixing high density poly-ethylene pipes or P.V.C. pipes for above ground work including cost of jointing materials paints |
| 25 | (A)Above Ground(i) 15 mm dia. |
| 26 | (ii) 20mm dia. |
| 27 | (iii) 25 mm dia. |
| 28 | (A) Labour for fitting and fixing G.I. pipes above ground (exposed) in structures with holder bat clamps including cost of jointing materials, holder bat clamps etc.,as necessary, including |
| 29 | Supply of PVC pipes & fittings Schedule 80 (medium duty) conformingto ASTMD - 1785PVC Pipes15 mm |
| 30 | (ii) 20mm dia. |
| 31 | (iii) 25 mm dia. |
| 32 | (B) Socket(Dia) 15 mm |
| 33 | (ii) 20mm dia. |
| 34 | (iii) 25 mm dia. |
| 35 | (C) Elbow(Dia) 15 mm |
| 36 | (ii) 20mm dia. |
| 37 | (iii) 25 mm dia. |
| 38 | (E) Tee(Dia) 15 mm |
| 39 | (ii) 20mm dia. |
| 40 | (iii) 25 mm dia. |
| 41 | (E) Tee(Dia)15 mm |
| 42 | (ii) 20mm dia. |
| 43 | (iii) 25 mm dia. |
| 44 | (H) Threaded Adopter(Dia) 15 mm |
| 45 | (ii) 20mm dia. |
| 46 | (iii) 25 mm dia. |
| 47 | (I) Union(Dia) (iii) 25 mm dia. |
| 48 | (J) Threaded End Cap(Dia) 15 mm |
| 49 | (ii) 20mm dia. |
| 50 | (iii) 25 mm dia. |
| 51 | (L) Reducing Socket (mm X mm)(Dia)20 X 15 |
| 52 | 25 X 15 |
| 53 | (M) Reducing Tee (mm X mm)(Dia)20 X 15 |
| 54 | 25 X 15 |
| 55 | (O) Solvent Cement250 Gm. |
| 56 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-3,Item-2[M4]Supplying, fitting and fixing in position G.I. pipes of TATA make for underground works with all necessary accessories,specials viz.socket, bend, tee, union, cross, elbow, nipple, short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.Payment for painting will be made seperately)(iii) 25 mm dia. medium quality |
| 57 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-22,Item-35[M4](b) Socket, Reducing socket, Bend, Plain equal elbow, Reducing elbow, Nipple, Short piece. (i) Upto 25 mm dia. |
| 58 | (c) Plain tee, Reducing tee, Pendent tee, Jamnut, Socket and Nipple.(i) Upto 25 mm dia. |
| 59 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-20,Item-23[M4]Supply, Fitting & Fixing of 32 mm PVC Waste Nozzle with jamnut, full thread or half thread complete. |
| 60 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-37,Item-6[M4]Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer(c) 1500 litre capacity |
| 61 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-41,Item-1[M4] Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets.(i) 450 mm X 300 mm size |
| 62 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-43,Item-9[M4]Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.(ii) 450 mm long |
| 63 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-79,Item-4[M4] Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or S\" trap (excluding cost of concrete for fixing).i) 580 mm X 440 mm |
| 64 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-81,Item-11[M4]Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.i) Polythene Flush Pipe |
| 65 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-82,Item-22[M4] Supplying, fitting and fixing towel rail with two brackets.(a) C.P. over brass (ii) 25 mm dia. and 600 mm long |
| 66 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-66,Item-14[M4]Supplying,fitting and fixing cast iron \"P\" or \"S\" trap conformimg to I.S. 3989/ 2009 and 1729/ 2002 including lead caulked joints and painting two coats to the exposed surface. (Painting to be paid seperately).(B) \"S\" Trap(ii) 75 mm |
| 67 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-3,Item-3[M4](a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 68 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-5,Item-4[M4] Supplying, fitting and fixing Peet\"s valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.).(vii) 25 mm dia |
| 69 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-5,Item-4[M4]Supplying, fitting and fixing Peet\"s valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.).(vii) 25 mm dia |
| 70 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-6,Item-7[M4] Supplying, fitting and fixing bib cock or stop cock. (e) PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent)15 mm |
| 71 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-82,Item-17(a)[E2].Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm |
| 72 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-82,Item-19[E4].Supplying, fitting and fixing liquid soap container.(a) Cromium plated. |
| 73 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-83,Item-23(i)[E4]. Supplying, fitting and fixing porcelain toilet paper holder of approved make with wooden spindle as necessary.(i) Roll type size 250 mm X 125 mm |
| 74 | PWD(WB),SANITARY AND DRAINAGE WORKS,Page-87,Item-1[E4]. Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials.ii) With Bazree (N.B Variety) (Other than SAIL/TATA/RIN |
| 75 | PWD(WB),BUILDING WORKS,Page-259,Item-1.[A3]Supplying and stacking of good earth (adequate for horticulture work) at site including royalty (earth measured in stack will be reduced by 20% for payment) |
| 76 | PWD(WB),BUILDING WORKS,Page-259,Item-2.[A3] Supplying and stacking sludge (adequate for Horticulture work) at site in dry cake form from approved disposal work site including royalty, all lead and lift etc. (Sludge measured in stack will be reduced by 8%). |
| 77 | PWD(WB),BUILDING WORKS,Page-259,Item-3.[A3] Spreading of sludge, dump manure,/farm yard manure/animel dung manure and good earth in required thickness. This includes supply of labour, tools & plants excluding materials |
| 78 | PWD(WB),BUILDING WORKS,Page-260,Item-5.[A3] Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 ( 8 parts of stacked volume of earth after reduction by 20%, one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary watering and finally fine dressing, levelling etc., including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50m lift upto 1.5m complete. This includes supply of labour, tools & plants including materials.Planting hedge plants in two rows at 30cm apart |
| 79 | PWD(WB),BUILDING WORKS,Page-260,Item-8.[A3] Maintanance of trees for one year (Avenue Plants) including watering, trimming, manuring, spraying insecticide and guarding as required. This includes supply of labour, tools & plants including materials |
| 80 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick |
| 81 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement |
| 82 | Providing and fixing conc. Sign board as per IRC specification of size 900x 750x37 mm thk made with IRC 1:1.5:3 with pakur variety stone chips reinforced with double layer IRC fabric (75x75)and fixed with necessary nuts & bolts.on two R.C posts 100x150 mm height 2.65mtr.etc....com |
| 83 | Electrification Charge @ 5% |
| 84 | Cost of 18% GST charge |
| 85 | Cost of Labour welfare cess 1% |
