|
| 1 | Cuttinguprootingandclearingjunglesincludingshrubs,waterweeds, bushes, trees, plants, upto 30 cm. girth including removing as directed by Engineer-in-charge. |
| 2 | Takingoutsluicegatedrawshuttergearing arrangements & pedestalincluding refittingthesamewith newnuts & bolts wherenecessary.(a) Up to 4 sqm.(i) Taking out and refitting the same. |
| 3 | (b) Above 4 sqm. and upto 7 sqm(i) Taking out and refitting the same. |
| 4 | (a) Up to 4 sqm.(ii) Taking out only. |
| 5 | Supplying, fitting, fixingMild Steel draw shutter with Mild Steel plate of thickness as specified by the Engineer-in-charge and other necessary Mild Steel sections for sluice including fabricating the same(as perdrawingandinstruction given by the Engineer- in-charge) excluding cost of Mild Steel guide channel, sill beam,gearing arrangement etc. but including painting with two coats of anticorrosive bituminous paint of approved make & brand over two coat of red lead primer and with necessary masonry work with all materials supply etc. completeatsite. |
| 6 | Painting on steel or other metal surface with any approved bituminous anticorrosivepaintafterpreparingthesurfaceincludingremoving paints, cleaning, smoothening etc. including scaffolding where necessary including cost of all materials complete. b) Two Coat |
| 7 | Supplying,fitting&fixinginposition rubber seal arrangements with musical note harmonic \"J\" type for making water tight in both up and down stream of draw shutter as well as flap shutter including guide paths, additional M. S. flats, bolts and nuts forfixing the rubber seal in position including fabrication cost and carriage of all materials to site and complete as per direction of the Engineer-in- charge.(b) Musical Note, Harmonic Type(ii) 127 mm x 6 mm |
| 8 | Oiling,cleaning &greasingtheregulatorgate&gate parts includingguide channel, top runner, pedestal block, gear rods, wheel,fishplateetc.withsufficientlubricantasand when necessaryasdirectedby the Engineer-in-chargeincluding cost ofall materials to site complete. |
| 9 | Supplying,fittingandfixingof MildSteelGuideChannelwith necessary Mild Steel lugs of required length and size by making holeintowallandfixingwithnecessarymasonryworkwith maintaining proper line and level as directed by the Engineer-in- charge. This item includes two coats of anti-corrossive bituminouspaint over two coats of red lead primer. Payment will be made on actual length of Guide Channel. |
| 10 | Earthwork in excavation in the canals / drainage channels / borrow pits /River bed / slope of bank as noted below as per designed section & throwing the spoils in layers of 25 cm. for making banks as per profile or to deposit the same in any other place within an initial lead of 30 metre and initial lift of 1.5 metre including breaking clods, rough dressing etc. complete as per direction of the Engineer-in-charge.(a) Ordinary soil / local soil / soil mixed with moorum or kankar / silt, dry or moist / slushy silt / sticky soil. |
| 11 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.a) In ground floor including roof |
| 12 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mmnominal size) excluding shuttering and reinforcement if any, in ground flooras per relevant IS codes.(i) Pakur Variety |
| 13 | First class Brick work in cement sand mortar in steining of well, pier, abutment, wing wall, parapets cross drain. H.P. culverts, guard wall etc. includingcuring, scaffolding, raking out joints etc. complete including cost and carriage of all materials.(a) In 1:4 proportion. |
| 14 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar(a) 20 mm thick plaster |
| 15 | Supplying/ReplacingGunMetalBushforscrewgearing arrangementrequiredforhangingarrangementofdrawshutter andfitting & fixingwith the screwgearing arrangement for operating the draw shutter by taking out the old screwgearing arrangement andGun Metal bush etc. complete as per direction ofthe Engineer-in-charge.(The old materials to bereturned to Departmental Godown.) (d) 80 mm. dia. |
| 16 | Supplying / Replacing Gear rod by a new Mild Steel Gear rod, threadedlengthasrequiredand fitting,fixinginpositionwith screwgearing arrangement for operating thedraw shutter including takingoutold gear rod by cutting bolts etc. complete as per direction of the Engineer-in-charge. (The old materials to bereturned to Departmental Godown.)(d) 80 mm. dia. |
| 17 | Supplying,fitting&fixingCastIron wheel (after taking out existing one if necessary), rim made of 28 mm. to 36 mm. dia to fit any size of gear rod including carriage to site, paintingwith two coatsof bituminouspaintovertwocoatsof red lead primer etc.complete as per direction of the Engineer-in-charge.(b) 60 cm. dia. Cast Iron wheel |
| 18 | Supplying / Replacing at site new pedestal or other similar items for sluices made with Mild Steel plates, angles, channels, holding down nuts & bolts etc. including fitting, fixing in position in concrete or masonry complete as per direction of the Engineer - in -charge. |
