Tender For Request For Qualification Cum Proposal For Interiors And Fit-Out Works Of New Office Space For Nicdc At Ht House, Kg Marg, New Delhi On Percentage Rate Basis, Delhi-Delhi

TDR : 48865606

Tender Notice
Corrigendum Details
BOQ

Expired

Delhi , Delhi

Tender Brief : Corrigendum : Tender For Request For Qualification Cum Proposal For Interiors And Fit-Out Works Of New Office Space For Nicdc At Ht House, Kg Marg, New Delhi On Percentage Rate Basis

Document Fees
₹ 59000 /-

EMD
₹ 1000000.0 /-

Tender Value
₹ 4.85 Crore /-

Submission Date
09-05-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !

Sr No	Corrigendum Date	Corrigendum	Type	New Submission Date
1	30-04-2025	Pre-bid Response	Other	09-05-2025

Name of Work: Interiors and Fitout Works of New Office Space for NICDC at HT House, KG Marg, New Delhi onPercentage Rate Basis

Sl. No.	Item Description
1	MASONRY AND PLASTER
2	Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
3	All works above plinth and upto floor V level
4	Concrete of M15 grade with minimum cement content of 240 kg /cum
5	Extra for concrete work in superstructure above floor V level for each four floors or part thereof.
6	Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
7	CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick wall of mix.
8	1:4 (1 cement : 4 fine sand).
9	12 mm cement plaster of mix
10	1:4 (1 cement: 4 coarse sand)
11	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
12	Centering and shuttering including strutting, propping etc. and removal of form for :
13	Lintels, beams, plinth beams, girders, bressumers and cantilevers
14	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
15	Hot rolled deformed bars
16	POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick POP Punning over cement plaster in line & plumb finished smooth to receive paint. (Internal surfaces of walls).
17	Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg /sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/ sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
18	AAC BLOCK FILLING: Providing and Laying of AAC Block Filling in the Slab Sunk or Raised Areas as a Back fill or platform. Laying should be done in layers with pounding done at every level to ensure a proper cavity free installation without disturbing any existing services in the area. Cost to also include haunching for plumbing pipes.
19	PAVING AND WET WORKS
20	TILE DADO :- Providing and fixing vitrifed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours of any size 1200mm x 600mm or as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
21	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
22	Glazed vitrified floor tiles polished finish of size
23	Size of Tile 600 x 1200 mm
24	Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.
25	Size of Tile 600 x 1200 mm
26	CERAMIC TILE FLOORING :- Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.
27	Grouting the joints of flooring tiles having joints of upto 5 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.
28	Size of Tile 600 x 1200 mm
29	Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm,comprising of modular load bearing floor panels supported on G.I. rectangular stinger framework and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and asdirected by Engineer-in-charge consisting of:
30	(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug.
31	(b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed bythe Engineer-in-charge
32	(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product.
33	300 mm Finished Floor Height (FFH)
34	KITCHEN/ PANTRY/ HAND WASH COUNTER :- Providing and fixing pantry and toilets with Granite stone top (with straight edge polished nosing) complete with base cabinet made of 20mm BWP board, outside surface (shutters) finished in 1mm thick Laminate of approved shade. All internal surfaces to have balancing laminate. The rate inclusive of necessary hardware, handle lock sets, self closing hinges, spring loaded shutter, latch inside, all cabinet hardware complete as per Architects approval. (BR of stone to be taken as Rs 1600/Sqmt). Width of work top counter 600mm/ detailed drawings.
35	Supply of modular carpet of approved model and shade and made with 100% nylon 6/6.6 tufted textured tiles of minimum 500mm x 500mm in size, stain resistant, anti microbial, and having colour fastness to water, fastness to light, rubbing fastness and castor chair suitability as per relevant standard for heavy commercial usage, with 100% PVC free Backing with having average density 6000 oz/cu. yd. or more,Nominal total thickness of 5.9mm, and Pile weight – 16-18 oz/ sq yard. Material shall be CRI GREEN LABEL PLUS certified, and shall have recycled content complying to GRIHA requirement, including fixing with GRIHA compliant adhesive of approved make, minimum 15 years manufacturer\"s warrantee, all complete as per drawings, manufacturer\"s specifications and direction of Engineer in Charge
36	Providing and Fixing of 15mm thick Engineered Woooden Flooring with plank width of 135/185mm and length of 1800/2100mm and top layer up to 3mm in approved finish. Surface of Top layer shall be pre finished with several layer of UV hardened Acrylic lacquer. The product shall be Free from Formaldehyde and solvents. Flooring plank shall be interlocked using Plank locking system in a glue less floating manner. Engineered wood planks shall be a composition of 3 layer of Pine wood with direction of each layer oriented at right angle to the adjacent layer of natural strain in Lacquer and Beveled in length and width as specified by the manufacturer-in-charge. Product shall be MAKE IN INDIA. The cost to include providing and fixing of all acessories i.e Skirting, beading, profile etc. and Underlay 2mm PE foam and polythene combo with 40 Micron complete as required.
37	PARTITIONS ANDWALL CLADDING
38	GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre.
39	The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture\"s specification and direction of engineer in charge all complete.
40	75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095:
41	Gypsum Panelling:-Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the ‘W’ profile (0.55 mm thick ) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-incharge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish.
42	Gypsum board conforming to IS: 2095 Part - I
43	12.5 mm thick
44	GLASS PARTITIONING:- Providing & Fixing Full Height Glass partition using 12mm Thk. Glass with anodised Aluminium frame fixing glass with snap on option consisting of top, bottom and side frame measuring 40-46mm x 18mm-26mm complete with glazing rubber as per manufacturer\"s specifications and instructions of Engineer- in-charge.Rate include supply & Installation of 12 mm thk toughened glass with double sided adhesive tapes for glass to glass butt joints. Partition system from FFL to False Ceiling level, inclusive of cost of support required for fixing in the ceiling.The frame to be powder coated in desired shade as per the instructions of the Architect.
45	PARTITIONING - Partition using 12mm thick fire rated plywood fixed on both sides on aluminium Studs Frame 50mm x 50mm x 1.5mm as per approved sample and architectural drawings placing the same 600mm (min) c/c in both directions . Aluminuim frame to be fixed to floorand RCC Ceiling using fastners. The cost to include finishing visible edges with 12mm thick mdf strip as per detail drawings.
46	PANELLING- Panelling using 12mm thick fire rated plywood fixed on one side on Aluminium Frame 50mm x 25mm x 1.5mm as per approved sample and architectural drawings placing the same 600mm(min) c/c in both directions. Aluminium frame to be fixed to walls, floor and RCC Ceiling using fastners.
47	Cladding using 12mm thick fire rated plywood on existing frame/ surface.
48	VEENER CLADDING- Providing and Fixing 4.0 mm thick decorative/ Natural Veneer of approved design and shade, cladded on to existing base. (base rate Rs. 1450/- sqm)
49	Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)
50	LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF, on an existing Plywood surface.
51	Providing and fixing of 1.25mm/1.50 thick laminates (as per IS:2046-1995,DIN EN 438, NEMA LD3-2005 quality standard), made out of urea free thermosetting resign treatedKraft as core material and design paper as a finish surface.water boiling test reflect the water immersion through permissible increase on thickness and mass <0.60%, Laminated should accomplish Antibacterial properties ( under JIS Z2801:2000, manufactured under EN438-2&3:2005 standard). The item to include proving and fixing of base of 4mm thick MDF with/without grooves as per appproved design.
52	INSULATION- Providing and fixingthermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.
53	Providing and Fixing of Channeled Woodworks perforated panelsCustom Perforated of width 192mm, thickness of 17mm and length 2440 mm , made of a HDHMR FR Grade board with minimum 860 Kg/M3 density substrate with a laminated facing as per the approved shade & finish (Khaya Mahagony/Fusion Mapple/ Bavarian Beech) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern of 3mm width Custom Perforaton of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece having NRC of 0.60. The panels shall be mounted on special aluminium splines (keel) using clips provided by manufacturer.INSTALLATION: Screw the aluminium extruded keel for channelled woodworks provided by manufacturer over the solid wall/ surface an on-centre distance of 600mm. Place the inside clip on the groove end of the panel along the Al keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Installation to be carried out by Trained Installation team & Installation should be carried out as per manufacturer recommended procedure.
54	Supply and installation of VMT Fabric Fluted 12mm PET panels which shall be processed with VMT technology for surface customised colour options with fabric pattern/ or as approved as per the designers requirement, the panel shall be made from -100% polyester fiber, with up to 70% recycled Fiber. size of panel 2800mm x 1200mm (± 0.5mm). Panel Should be mostiure resistant and also Non-toxic, non-irritant, and fire-resistant complying with safety standards confirm to Class 1 Fire Ratings tested as per BS 476 Part 6 (Fire Propagation) & Part 7 (Surface spread of flame) ,ASTME 84 CLASS A, EN 13501 PART 1C,2S for interior applications. Noise reduction coefficient (NRC) -0.3 with direct fix method, 0.85 with 25 mm gap with infill, 0.95 with 50 mm gap with PET WOOL infill. The product should be 100% make in india and OEM must have ISO CERTIFICATIONS- complying to- IGBC Membership ISO 14184-2 (Release formaldhyde)ISO 9001 (Quality Mangement System)ISO 14001 (Environmental Management System)ISO 45001 (Ocupational helth & safety management system)The cost to include advesive and/or any other accessory required for fixing complete as per instructions of engineer - in -chage
55	SHELVES:- Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).
56	25 mm thick
57	SHUTTERS:- Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS:12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge
58	LAMINATED STORAGE CABINET FOR GENERAL STORAGE- Out of 19mm Commecial Ply Board finished using 1mm thick laminate. The storage shall be complete with all hinges, drawer glides and hardware from approved make. All internal surfaces to be completed using balancing laminate. Including brass D-type handles for shutters and recessed type handles for drawers. Storage to be of all heights as per design. Storage shutters to be made in solid laminate/ glass as per design and drawings.
59	VENEER STORAGE CABINET FOR GENERAL STORAGE- Out of 19mm Commecial Ply Board finished using 4mm thick veneer and polished in melamine to match the veneer cladding item. The venner to be same as the venner cladding under separate sub- head above complete with all hinges, drawer glides and hardware from Hettich or equivalent. All internal surfaces to be completed using balancing laminate. Including brass D-type handles for shutters and recessed type handles for drawers. Storage to be of all heights as per design. Storage shutters to be made in solid veneer/ glass as per design and drawings. (Base Rate of veneer -Rs. 1450/- sqm)
60	STORAGE CABINET FOR ELECTRICAL PANEL AND VOLTAGE STABLIZERS- Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm Laminate. Shutters to be fixed to a frame. Rigidly fixed on both sides and top finshed in laminate. No internal carcass required. All Hinges of hettich or equivalent. Internal Surface of the shutter in balancing white laminate. All shutters to be provided with Stainless steel louvers at the top and bottom of the shutter as per the site requirementsand instrcution of the Engineer In charge.
61	CEILING
62	GYPBOARD CEILING :- Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed withintermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long.
63	Including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
64	12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I
65	Providing and fixing suspendedStratopanel, Size 1200X2500X12.5mm round random perforation G8/15/20 with 9.9% perforation, NRC upto 0.55 : Round rectangular perforation of glass-fibre reinforced gypsum material, which includes providing and fixing GI perimeter channels of size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from the soffit at 900 mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55 mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the intermediate channels with help of connecting clips and in direction perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25 mm dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to be joined and finished so as to have a flush look with uniflot. The false ceiling surfaces shall be prepared to the satisfaction of the EIC
66	600MM X 600MM MINERAL FIBRE GRID - Providing & Fixing of Mineral Fibre Ceiling Tiles With 15mmGRID.The tiles should have Humidity Resistance (RH) of 99%, NRC 0.6, Light Reflectance ≥85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour White, in module size of 600 x 600 x 16mm. The tile shall be installed with 15*38(web hight) wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm and need to be installed with Suspension system of manufacturer.The Tile & Grid system used together should carry a 10 year warranty. INSTALLATION: The grid should be with 15mm wide T - section flanges color white.The main T runner with length andsize of15X38mm made from .30mm thick sheetspaced at 1200mm Centre to Centre and cross T of size 15X38mm made of .3mm thick of 1200mm long spaced between main T at 600mm center to centre to form a grid of 1200X600mm and second cross T of length 600mm and size 15X38mm made of 0.30mm sheet to be interlockedat middle of the 1200X600 mm panel to form grid of 600X600mm and wall angleof size 19X19 Installation should becarried out as per recommended procedure. The grid frame should be suspended from ceiling using M-6 fastener, L Cleat, 4mm GI wire with Stainless steel level adjustible clip which will be attached to Main Runneratspaced of 1200 c/c
67	TRAP DOOR :- Providing & fixing Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard ( Knauf Brand) Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire ). 10. Powder coating - Color: white, RAL 9010/ or as approved complete as per instructions of engineer-in-charge.
68	600x600
69	CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and made hardwoodframings hung from ceiling @1000mm centre to centre with 2 nos of 6mm thk. Commercial ply on vertical & 12mm thk. Commercial ply on horizontal surface (straight & curved). Inclusive of finishing in Paint.
70	WOODEN VENEER CEILING :- Providing and fixing wooden veneer ceiling by Fixing Natural Teak Veneer on 12mm Underlay commercial Ply fixed to a subframe made using 50mm X 50mm Kiln seasoned and chmeically treated hollock wood fixed to RCC ceiilng using Fastners complete as per the instructions of the Engineer In Charge. (base rate of veneer Rs. 1450/- sqm)
71	Providing the gypsum double sided cove of 150mm x 150mm having a facia of 75mm to macth the specifications same as gypsum ceiling.
72	Providing the gypsum single sided cove of 150mm x 150mm having a facia of 75mm to macth the specifications same as gypsum ceiling.
73	GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the mineral fibre/ gypsum ceiling. In order to make the Mineral Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto 100mm as per drawings. (visible surface of gypsum band to not exceed 100mm) including plastic emulsion paint.
74	Providing of Baffle ceiling system comprises of 50 mm x 100 mm (50 mm width & 100 mm Height) U Shape panels in wooden finish. Panels shall be made of 0.5 mm thick galvanized steel after Powder-coated and length up to 4000 mm. Panel shall be high corrosion resistance and good color stability. Centre to Centre panel gap will be 100 mm. Panels are fixed on to roll formed carriers 20 mm wide x 40 mm deep out of 0.80 mm G.I sheet Powder-coated color with cutouts to hold the panels in module of 50 mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 6 mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max. 1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon inserts. Panels are factory cut in lengths up to maximum 4.0 m to suit site dimensions or shop drawings. Top cap and side cap are used to cover the edges of the panels.
75	Providing and fixing of linear cell ceiling made out of Aluminium. The assembled cell ceiling panels shall be in size of 600x1200. The assembled cell ceiling panels shall made out of main blades in 3mm (W) x 20mm (H) in 1200mm (L), installed at 30mm c.c. and cross connected to secondary blades in 9mm(W) x 22mm (H) in 600mm (L) with 375mm pitch. The assembled cell ceiling panels are then clipped into U-94 carriers in Aluminium, pre-coated in black enamelled finished at 1200mm c.c. Wire clips shall hold the cell ceiling panels into the U-94 carriers. Once the U-94 carriers are installed then primary angles made out of GMS, type U1040 are cross connected to the U-94 carriers at 1200mm c.c. for lateral bracing The whole ceiling shall be suspended by M6 threaded rods installed 100mm c.c.All panel modules must be hingeable through wire clips.Finish of cell ceiling panels shall be as per approved sample. The cost to include all neccesary hardwares and fixing accessories required complete in all respects.
76	PET BAFFLES: Providing and fixing of PET acoustic baffles OF SIZE 401202400MM made from standard 25mm PET panels of size 2440mm x 1220mm. The centre to centre spacing can be in multiple of 25mm. Maximum length of one baffle can be 2440mm and can be increased by joining two or more baffles. The baffles to be installed with help of specially designed U clamps, 25mm x 25mm x 25mm GI carrier powder coated in black. Spacing between two carrier to be 1200mm. The carrier should be supported from true ceiling with help of 4mm threaded rods. The NRC of baffle system to be 0.5.
77	DOORS/ WINDOWS
78	35MM THICK VENEER FLUSH DOOR WITH FLOOR SPRING- 35mm thick flush Doors finished using 4mm Thick veneer on both sides panel of size upto 2400mm x 1200mm complete with Hardware including floor spring, Door Closer, dead Lock with inbuilt key, 1200mm D-Handleetc. including cost of teak lipping all around. All surfaces to be finished in melamine polish as per approval. The item to include installation of all kinds of latches as per the requirement.
79	STILE DOOR - Providing & Fixing of Stile Door System having size of 7545 with Door Frame formed out of 45 40mm / 50*50mm of 6063-T6 Virgin grade duly Anodized Aluminium, including 10 mm Toughened Glass. The cost to include hardware like Door Closure, 4nos Hinges, Lever Handle with mortice lock, Door Seal & Gaskets etc. in approved shade and design as per architectural drawings and instructions of the architect. The size of door shall be upto 1050mm X 2400mm.
80	DOOR FRAMES- Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).
81	Second class teak wood
82	Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).
83	LAMINATED FLUSH DOOR- Flush Doors finished using 1mm Thick Laminate on both sides panel of size upto 2400mm x 1000mm complete with Hardware including hinges, Door Closer, Mortice Lock with Handle, latches etc. including cost of Door frame with melamine/ duco finish. The cost to include providing and fixing of vision panel as per design.
84	DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
85	FIRE DOOR- Providing and fixing single leaf 120min Rated Fire Door of size 1050x2400. with vision panel using wired glass complete with Fire proof door frame. One side to be finished in fire retardant paint and one side to be finished in Laminate of approved shade. All Frame to be finished in fire retardant paint. All hinges and hardware to be thermatically sealed and 120 mins fire rated.
86	FINISHES & MISCELLANEOUS
87	Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :
88	Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm
89	Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
90	In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
91	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:
92	Two or more coats on new work
93	Providing & fixingdecorative Poly décorfabric Wall Paper (on walls and ceiling) of weight 475g /sqm asperapproved shade & design including prepration of surface with 2 coats of Nubin Glue based epoxyquote.
94	ZEBRA BLINDS -Providing & fixing of Twist Window Shadings Blinds as per the sample shown having room darkening fabric strip and sheer fabric strips alternately in such arrangement as when light filering strips overlap each other, it creates visibilty and once the light filtering strips overlaps the sheer ones, it creates the no visibility effect.It has bottom rail made of aluminium alloy extruded profile, powder coated and provided in fabric coordinated colour. The rolling tube should be made up of aluminium alloy from extruded profile of Ø34mm.The fabric of this Blind should be made up of 100% anti-static polyester vanes having light filtering and sheer vanes to reduce glare.Sheer layers made of white 100% knit polyester & the selection of colors, textures and opacities as per Engineer-in-charge.The FABRIC shall be constructed from spun-bonded 100% polyester fiber, having Green guard Certification treated with soil & dust repellant require minimum regular interval cleaning. The fabric has a maximum width of 2.80 M and a thickness of 0.38mm (+ 5%) and having weight of 272g/m2 (+ 5%).The strip size is Solid 8.5 cm /Sheer 6 cm. The shading to be operated by Easy rise mechanism with a continuous cord loop operating option.All plastic parts are in white color.Installation to be done by quick release brackets (wall or ceiling).
95	ROLLER BLINDS - Providing & supplying of Window Blinds as per the approved sample in required shade and style consisting, of Roller Blinds comprising of optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sqm, Thickness 0.67 mm, Yarn count 18-19/cm, having fire resistance standard – NFPA 701-89 small testing ISO-5659-2. The tear resistance should be complying to ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and safe installation, molded plastic with steel spring support and inserted into the tube end. It shall be driven by a ball chain pulley with ball chain and can be positioned at right side or left-hand side of the Shade. The Shade when lowering or raising, shall be automatically locked in position upon release of the ball chain by means of a built-in friction lock. Universal clutch for left- and right-hand operation. Chain Gear Ratio of 1.75:1. The END PLUG shall be molded of plastic with a steel location pin. The plug shall be inserted into the tube end. (Opposite to the Drive Unit) for ease of installation. The SUPPORT BRACKETS shall be of coated steel & provided with covers and used in right hand or left-hand positions differentiated by the acceptance of the of the rectangular drive unit support or the round idler plug pin. Can be installed (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The Bracket should be protruding outside maximum of 80mm.The ROLLER TUBE shall be of extruded aluminium with 37mm internal diameter & skin thickness of 1mm and shall incorporate a keyway integral with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom made up of powder coated steel. The BALLCHAIN shall be 2mm diameter cord with 4.5mm diameter acetal balls molded co-axially to it on 6mm pitch to form an endless ball chain. It is used for raising or lowering action of the shades.
96	Reception Table:-Providing & Installation ofReception table of of size upto 2.1m x 0.75m x 0.75m/ 1.2m (ht), made out of 19mm thk. Commercial Board finished in AcrylicSolid Surface of approved shade and colors complete as per design. One (1) number Drawer pedestal with 3 lockable drawers and channels (all hardware from Hettich) to be provided under the table to be finished in Solid Acrylic surface.All visible surfaces to be finished using Acrylic solid surface as per details.
97	Preparation of complete set of drawings including finishing, details, etc. and any other details as and when desired by Engineer In charge /client. A qualified professsional for the purpose shall be appointed after due appproval from Engineer In Charge.
98	FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface with 15 yrs MCS warranty as approval of the Architect. (Only film surface area shall be measured and paid).
99	Providing and fixing of 4,6 mm thick annealedGRIHA rated lacquered glass manufacturedindustrially by curtain coating process with PU lacquer (50 micron thick), opaque (if viewed against a support wall) conforming to EN 16477 standards for back painted glass , of approved color by Architect/ Client fixed with compatible Silicone having Shear Bond Strength (Dry, 24 hours), greater than 450 kpa and tack free time of 10 to 30 mins compatible for installation of mirror and lacquered glass / Foam based double sided adhesive tape for instantaneous adhesion, compatible with mirror and lacquered glass having Shear bond strength (Dry, 15 mins) of 250 to 350 kpa)on a perfectly leveled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. The contractor should submit test reports for backpainted glass from manufacturer -High humidity Resistance(conforms to BS EN 1036 1999); Color fastness ISO 105B02 standard & Mechanical Resistance ISO 7784 ( Taber Abrasion test ) ISO 2409 ( Cross Hatch Test ) standard The manufactured backpainted glass should be environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial / 6% post consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass
100	Painting of walls, ceiling, RCC works, HVAC ducting, grills diffusers, conduits etc. with 2 or more coat of duco paint to achive smooth finish. The item to include cost of all base preparation, priming etc. complete.
101	Providing & fixing 12mm Thick. 100% Acrylic solid surface of approved make and colour using approved Adhesive to 12 mm thk. Waterproof Plywood of approved brand as per shape, pattern & details given in the drawing. The rate includes providing & fixing beading, cutting, scaffolding, nails, all materials, labour, lead, lifts, HOM etc., complete.-for Lift Cladding. (The make, Shade, pattern etc., to be approved by EIC).
102	IPPBX & DISPLAY
103	Supply, Installation, Testing & Commissioning of Server based Communication System with all the required Software licenses and Hardware- IP-PBX/IP Telephony Communications Server: The IP Telephony Solution shall support the following Services - Voice, IM, Presence and Audio Conference The IP Telephony Solution should support H.323 and SIP The Solution should support the following Trunks - FXO, E1 PRI and SIP The IP Telephony solution should incorporate all licenses for the Phones and Trunks Solution should support all Extensions from Day 1 with future scalabilityupto 500 users. Licenses for all Phones supplied should be provisioned on Day1 Solution should support Hard 10 IP Phones, Softphones, Video Phones, 100 Analog Extensions with necessary Licenses, Rack mount architecture, complete as required and as per technical specifications.or its equivalent specifications
104	Supply, Installation, Testing & Commissioning of Color display—2.8 inches x 2.1 inches (7.0 cm x 5.3 cm)—Diagonal width: 3.5 inches (8.8 cm)▪ 8 buttons with dual LEDs (red, green)▪ 4 softkeys▪ Hard buttons for phone, messages, contacts, history, home, navigation cluster,headset, speaker, volume, mute▪ LEDs for speaker, mute, headset, message, history▪ 24 administrative buttons▪ Wideband audio in handset and headset▪ Full duplex speakerphone ▪ Ergonomic hearing aid compatible handset supports TTD acoustic coupler▪ Message waiting indicator▪ Mute indicator with optional mute alerting▪ IC call alerting with 360-degree visibility▪ Rich, classic, alternate, and downloadable ringtones▪ Dual-position stand, optional wallmount stand▪ Gigabit Ethernet (10 / 100 / 1000) line interface▪ Second Ethernet interface 10 / 100 / 1000 Mbps▪ PoE Class (IEEE 802.3af) registers as class 1 device and supports 802.3az▪ Optional AC to 5 volt adapter▪ Order Custom Bezels / Faceplates▪ SIP & H.323 protocol support▪ Standards-based codec support: G.711, G.726, G.729A / B, G.722, Opus.▪ Zero touch deployment via Device Enrollment Services Support▪ Supports the following languages: Arabic, Brazilian Portuguese, Simplified Chinese, Dutch, English, Canadian French, Parisian French, German, Hebrew, Italian, Japanese, Korean, Polish, Latin American Spanish, Castilian Spanish,Thai, Turkish, and Russian. or its equivalent specifications
105	Supply Installation, Testing and Commissioning of Analog Speaker Phone with backlight. or its equivalent specifications
106	SSupply, Installation,Testing and commisioning of IP phone license complete as required
107	Supply, Installation, Testing and Comissioning of 75\"\" LED display. Brightness -500nits or better, Resolution- 4K UHD or better, Viewing Angle (H/V) - 178/178 or better, Contrast Ratio - 4,000:1 or better,Ports - Minimum 2 x HDMI, 1 xDisplay port, 2xUSB, 1 x RJ45, 1xRS232 or more. Bluetooth and WiFi connectivity options.With standard accessories and suitable MS wall mounting bracket. (For CMD Cabin)
108	SANITARY FIXTURES & FITTINGS
109	Supply, installation, testing and commissioning of glazed vitreous china single trap syphonic pattern having back inlet, supporting chair, wall hung water closet complete with all internal fittings/ accessories and CP brass flush bend (European type) water closet with seat and lid, with C.P. brass hinges and rubber buffers, adapter, rubber joints fixed to W.C., C.P. brass screwed washers including cutting and making good the walls and floors wherever required and HDPE WC pan connector including jointing with white cement complete in all respects.
110	Wall hung W.C. pan (White colour)with white plastic seat & lid \"Thermoset moulded ( bakelite ) IS 2548 Part I
111	Supply, installation, testing and commissioning of concealed cistern including flush plate and all internal fittings/ accessories including cutting and making good the walls and floors wherever required complete in all respects.
112	Supply, installation, testing and commissioning of glazed vitreous china wash basin with R.S. or C.I. brackets painted white, 32mm C.P. brass waste of standard pattern , C.P brass wall flange 32 mm dia. C.P. brass bottle trap and union 32 mm dia C.P. pipes to wall flange. complete including cutting and making good the walls wherever required.
113	Undercounter wash basin
114	Table top wash basin
115	Providing & fixing vitreous chinaware urinal comprising Large flat back wall hung urinal in glazed vitreous China urinal 15 mm electrically operated solenoid valve with infra red sensor mounted in a box with SS Cover. CP brass chromium plated flush piping from solenoid valve to urinal terminated with a 15 mm screwed spreader 32 mm nominal bore CP cast brass waste 32 mm nominal bore CP cast bottle trap with extension pipe rubber adopter for waste connection, CP brass wall flange.
116	For supply,installation,testing & commissioning of sanitary fixtures(white colour) as per above details.
117	Supply, installation, testing and commissioning of 15mm C.P.brass single hole wash basin mixer without popup waste system with 450mm long copper pipes and brass nut
118	Providing & fixing toilet paper holding including cutting and making good the walls.
119	Providing & fixing Horizontal liquid soap dispenser with stainless steel lid and brackets fixed to wooden cleats with C.P. brass screws.
120	Providing & fixing C.P. brass coat hooks fixed on toilet door with C.P. brass screws
121	Providing & fixingbevelededge mirror 5.5mm thick of superior quality plate glass complete with 6mm thick marine plysheetground fixed to wooden cleats with CP brass screws and washerswith 40 mm wide teak wood frame as per design including polishing
122	Providing & fixing Hand Shower (Health Faucet) with 8mm dia, 1M long PVC tube and wall hook CP brass wall flange
123	Providing & fixing, testing and commissioning of storage type electric water heater with automatic thermostatic control electric element, pressure release valve, brackets fixed to expansion fasteners with M.S. nuts and bolts all complete including cutting and making good the walls wherever required.
124	05 litres capacity (Horizontal /Vertical type1.5 kw electrical load).
125	15 litres capacity (Horizontal /Vertical type1.5 kw electrical load).
126	Providing & fixing wall mounted 25 mm dia Stainless steel coated grab bar including cutting & making good the walls(size 450mm long)
127	Providing & fixing 15 mm dia C.P. brass bib cock with C.P. wall flange of approved quality.
128	FRAGRANCE DISPENSER MACHINE :-Providing and fixing of Automatic Fragrance Dispenser machine complete with refill can and \"C\" size battery (2 Nos) for operation fixed to wooden cleats with CP brass screws
129	Providing and fixing of stainless steel finish Paper Towel Dispenser having capacity of 300-350 paper towels fixed to wooden cleats with C.P. brass screws
130	Providing and fixing of wall mounted fully automatic hand dryer in SS/ black finish as per approval complete will all accessories.
131	WATER SUPPLY
132	Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all (CPVC) plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This including jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. .
133	Internal Work - Exposed on Wall
134	25 mm nominal outer dia pipes.
135	32 mm nominalouter dia pipes.
136	40 mm nominal outer dia pipes.
137	50 mm nominal outer dia pipes.
138	Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVCplain & brass threaded fittings i/cfixing the pipe with clamps at 1.00 m spacing. This including jointing of pipes & fittings with one step CPVC solvent cement andthe cost of cutting chases and making good the the same including testing of joints complete as per direction of engineer in charge.
139	Concealed work oncluding cutting chases and making good the walls etc.
140	20 mm nominal outer dia pipes.
141	25 mm nominal dia Pipes
142	32 mm nominal dia Pipes
143	Providing and fixing brass stop cock of approved quality complete.
144	15 mmnominal bore
145	20 mmnominal bore
146	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):
147	25 mm nominal bore
148	32 mm nominal bore
149	50 mm nominal bore
150	Providing and fixing C.P. bass angle valve for basin mixer and geyser points of approved quality conforming to I.S:8931 a) 15 mm nominal bore.
151	15 mm nominal bore
152	Providing and fixing unplasticised P.V.C connection pipe with PTMT Nuts coller and bush of approved quality and colour.
153	15mm nominal bore with 45cm length
154	INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES)
155	Providing and fixingcast iron trap of self cleansing design withcast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.
156	100 mm inlet and100 mm outlet centrifugally cast (spun) iron S&S as per IS 3989.
157	Providing and fixing soil, waste and ventpipes.
158	Centrifugally cast (spun) iron S&S pipeas per IS 3989.
159	100mm dia cast (spun) iron S&S pipe
160	Centrifugally cast (spun) iron S&S pipeas per IS 3989.
161	75mm dia cast (spun) iron S&S pipe
162	Providing and fixing single equal plain junction of reqd. degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.
163	100x100x100mm
164	Sand cast (spun) iron pipe IS-3989
165	75x75x75mm
166	Sand cast (spun) iron pipe IS-3989
167	Providing and fixing single equal plain junction of reqd. degree.
168	100x100x100mm
169	Sand cast (spun) iron pipe IS-3989
170	Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.
171	75x75x75mm
172	Sand cast (spun) iron pipe IS-3989
173	100 mm dia
174	Sand cast (spun) iron pipe IS-3989
175	75 mm dia
176	Sand cast (spun) iron pipe IS-3989
177	Providing and fixing bend of required degree .
178	100 mm
179	Sand cast (spun) iron pipe IS-3989
180	75mm
181	Sand cast (spun) iron pipe IS-3989
182	Providing and fixing collar.
183	100mm
184	Sand cast (spun) iron pipe IS-3989
185	75mm
186	Sand cast (spun) iron pipe S&S IS-3989
187	Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.
188	For 100mm dia. Pipe
189	For 75mm dia. Pipe
190	Providing and fixing G.I. Pipes completewith G.I. Fittings and clamps.includingcutting and making good the walls etc.
191	32 mm nominal bore
192	40 mm nominal bore
193	50 mm nominal bore
194	PaintingG.I. Pipes and fittings with two coats of anticorrosive bitumastic paint of approved quality
195	32 mm nominal bore
196	40 mm nominal bore
197	50 mm nominal bore
198	Painting sand cast iron / centrifugally cast iron( spun) iron soil, waste and vent pipes and fittings with paint of any colour such as chocolate, grey or buff etc. over a coat of primer (of approval quality) for new work
199	100mm dia cast (spun) iron S&S pipe
200	75mm dia cast (spun) iron S&S pipe
201	Providing and fixing G.I. Inlet fitting of suitable size with 2 & 3 Nos. G.I. Socket 32 & 40 welded G.I. pipe and dipped in hot bitumen complete in all respect.
202	100 mm diameter pipe(Hopper )
203	Providing and fixing G.I. Inlet fitting of suitable size with 2 & 3 Nos. G.I. Socket 32 & 40 welded G.I. pipe and dipped in hot bitumen complete in all respect.
204	100 mm
205	75 mm
206	Providing & filling the joints with spun yarn,cement slurry & cement mortar 1:2(1 cement: 2 fine sand) in SCI/CI pipes.
207	75 mm
208	100 mm
209	Providing and fixing single unequal plain junction of reqd. degree.
210	100x100x75mm
211	Sand cast (spun) iron pipe IS-3989
212	SPRINKLER PIPING & ACCESSORIES
213	Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
214	25 mm dia
215	32 mm dia
216	40 mm dia
217	50 mm dia
218	65 mm dia
219	80 mm dia
220	100 mm dia
221	Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/ gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :
222	100 mm dia
223	150 mm dia
224	Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all accessories as per manufacturer\"s specifications.
225	CO2 gas nozzle type - 9 Litre capacity (IS:15683).
226	Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683).
227	ABC dry powder stored pressure type 6 kg capacity (IS:15683).
228	Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :
229	Concealed Sprinkler
230	Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.
231	1000 mm
232	Providing and fixing signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+ -10%) containing lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats anchor fasteners etc. complete in all respacts as diercted by Engineer-in-charge
233	Providing, jointing andtesting of automaticaly operated Halotron fire extinguishers(cap-5kg,temperature rating-68degc,test pressure-30bar) complete with all accessories/fittings.
234	Furniture
235	Providing and Placing Main TAble of Size 3000x2550x740.MAIN WORKTOP Size 3000x1050x740, ERU 1500x600x610mm- Main worktop - Made of 43mm Thick (±1) combination of MDF and particle board with top veneer face coated with clear lacquer. All edges are edge banded with matching 1mm thick veneer lipping.LEATHER PAD:Made of 18mm Thick (±1) MDF with Leatherette wrapped around top surface. This leather pad is fixed to main top panel.DRAWER UNIT:Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination ofMDF and particle board with top veneer face coated with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with leatherette on top surface.Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit is secured with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm Thick (±1) combination of MDF and particle board with top veneer face coated with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty is fitted with aluminum trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Door is fixed with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side panel for security.ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2 USB power points, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6connections.
236	SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE PERFECT HIGH BACKCHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for25% compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm.(W) x 76.7 cm.(D) ARMRESTS: The armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up- Down adjustment has 8 position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm range).Armrest top is made up of high density PU molded over glass filled Poly- amide inner.POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type. Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3-position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth canbeadjustedinsittingposition.Seatdepthadjustment rangeisof5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with an Up-Down mechanism assembly. BackHeight can be adjusted in sitting position. Itcanbe adjusted in therange of7.5+0.5 cm.PNEUMATICHEIGHTADJUSTMENT:Theheavydutyclass4pneumaticheightadjustmenthasan adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-center dia. TWIN WHEEL CASTOR:5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.50.1cm wheelDiameter and assembled to pedestal.
237	SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.- FULL BACKCHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for25% compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm.(W) x 61.8 cm.(D) ARMRESTS: The armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up- Down adjustment has 8 position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm range).Armrest top is made up of high density PU molded over glass filled Poly- amide inner.MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving type. Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3-position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth canbeadjustedinsittingposition.Seatdepthadjustment rangeisof5.0$0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with an Up-Down mechanism assembly. BackHeight can be adjusted in sitting position. Itcanbe adjusted in therange of7.5+0.5 cm.PNEUMATICHEIGHTADJUSTMENT:Theheavydutyclass4pneumaticheightadjustmenthasan adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-center dia. TWIN WHEEL CASTOR:5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.50.1cm wheelDiameter and assembled to pedestal.
238	Providing and placing in position discussion table.The overall size of the wortop shall be 2100mm x 1150mm x 740mm. Worktop shall be made from 25mm thick MDF one side prelaminate boardwith 0.4mmand having chamfered edge. Soft closing dual access flap provided for access to power supply and data cables. The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics.The product has a knock-down construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. A Powerbox with 2 cutouts on either sides for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting .Audio Visual Cables(eg. HDMI,VGA-A,etc). The product must be UL Greenguard certified.Complete all as per the direction of Engineer in Charge.
239	Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.
240	Providing and Placing mid Back Chair with overall size of 76.1 cm W x 76.1 cm D x 96.5 – 114 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.
241	Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the aestheticsS Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch , Zigzag Spring - 3.8mmComfort-The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with sinking feeling.Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.
242	Providing and placing sofa of size 1520mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the aestheticsS Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch , Zigzag Spring - 3.8mmComfort-The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with sinking feeling.Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.
243	Providing and placing sofa of size 750mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the aestheticsS Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch , Zigzag Spring - 3.8mmComfort-The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with sinking feeling.Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.
244	Providing and placing in position Centre Table having a size of : 1000mm(L) x 600mm(D) x 425mm(H). Understructure of the table which includes Legs, top wooden frame & bottom tie members are made out of first quality rubberwood of approved make without knots &defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm thick toughened glass of approved make. Construction: Knock-down assembly.Wooden members are PU painted with hardness-2H. Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral pattern on bottom surface 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts, wooden dowel, plastic leg bush. Complete all as per the dimension of Engineer-in-charge.Complete all as per the direction of Engineer in Charge.
245	Providing and placing in position CornerTable having a size of : 500mm(L) x 500mm(D) x 425mm(H). Understructure of the table which includes Legs, top wooden frame & bottom tie members are made out of first quality rubberwood of approved make without knots &defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm thick toughened glass of approved make. Construction: Knock-down assembly.Wooden members are PU painted with hardness-2H. Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral pattern on bottom surface 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts, wooden dowel, plastic leg bush. Complete all as per the dimension of Engineer-in-charge. Complete all as per the direction of Engineer in Charge.
246	Providing and Placing in position Conference table for 19 seaterhaving8Nos of 2Seater Modules of size 1350mm X 600mm X 740mm , 2 Nos of one seater module . Worktop- Madeof 25mm thick MDFone side prelaminate board conforming to IS14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge.Plastic ABS access flap is provided for easy access to wires and cables.Modesty consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction.It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction.An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated(DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injectionmoulded plastic part polymer component is fitted to pull out audio,video cables ontoworktop and connect devices charger to power socket below worktop.
247	Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.
248	Providing and Placing Mid Back Chair with overall size of 76.1 cm W x 76.1 cm D x 96.5 – 114 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.
249	Providingin place of main table with overall size of table 2350 x 2350 x 750mm. The main table shall be of size 2350 x 1150 x 750mm. The side unit shall be 1200 x 600 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.
250	The Back Unit shall be of dimensions 2350 x 500 x 750mm. It shall be made of 25mm thick MDF– one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security.
251	Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.
252	Providing and Placing Mid Back Chair with overall size of 76.1 cm W x 76.1 cm D x 96.5 – 114 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.
253	Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H. The seat should bemade of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should beupholstered with fabric or leatherette. 2) BACK FOAM: The back should bemade of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should bemade up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should bea welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.
254	Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat should bemade of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should beupholstered with fabric or leatherette. 2) BACK FOAM: The back should bemade of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should bemade up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should bea welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.
255	Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shallbe a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions oftable shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.
256	Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shallbe a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762.overall dimensions oftable shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.
257	Providingin place of main table with overall size of table 1650 x 1650 x 750mm. The main table shall be of size 1650 x 750 x 750mm. The side unit shall be 900 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.
258	The Back Unit shall be of dimensions 1650 x 500 x 750mm. It shall be made of 25mm thick MDF– one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security.
259	The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm.The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. The neckrest assembly consists of upholstered neckrest inner(material-poly propylene) with moulded polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck rest cover. neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Heightfrom ground - min 109.3 to max 124.4 cm. Seat height - min 45.5cm to max 55.5cm.Dimensions tolerance / variations shall be within +/- 1 cm.
260	The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm.The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from pedestal below. Heightfrom ground - 99 cm. Seat height - 49 cm.Dimensions tolerance / variations shall be within +/- 1 cm.
261	Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat should bemade of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should beupholstered with fabric or leatherette. 2) BACK FOAM: The back should bemade of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should bemade up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should bea welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.
262	Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shallbe a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions oftable shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.
263	Providing and placing in position discussion table.The overall size of the wortop shall be 3000mm x 1150mm x 740mm. Worktop shall be made from 25mm thick MDF one side prelaminate boardwith 0.4mmand having chamfered edge. Soft closing dual access flap provided for access to power supply and data cables. The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics.The product has a knock-down construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. A Powerbox with 2 cutouts on either sides for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting .Audio Visual Cables(eg. HDMI,VGA-A,etc). The product must be UL Greenguard certified.Complete all as per the direction of Engineer in Charge.
264	Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.
265	Providing and Placing mid Back Chair with overall size of 76.1 cm W x 76.1 cm D x 96.5 – 114 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.
266	SupplyingofRectaworkstation of size 1200 X600x 750 withKBPT .Providing DESK based modularworkstation withworktop thickness 25mm System ht - 750 mm .Understructure -The slanted legs with perforated metal modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management : Metal powder coated power box with wire raiser+D56 is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches.Worktop mounted metal modesty made from 0.8 mm thk CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ, GRIHA, BIFMA certified.
267	Providing and placing panel & tile based modular workstation with KBPT, Pedestal and CPU trolley. Size of Modular Workstation shall be 1500 X 1500 with partition thickness of 52.4 mm thick and ht – 1200 including powder coated aluminum trims. Work top shall be pre laminate particle board ,`below the work top is also pre laminate particle board. The panel thickness comprises of 38mm (35 mm Minimum) thick paper honeycomb + 3mm MDF on each sides + 3.6mm thick line gap each side+ 0.6mm decorative laminate or fabric on both sides. Tiles: Combination of top tiles shall be fabric magnetic/fabric/fabric tack able /white board/glass writing board/ clear glass tile/ plain metal/ prelaminated tile.Bottom tiles: Plain metal/ fabric magnetic/fabric/laminated/prelaminated . SPLIT Tiles: Combination of two finishes for the top tiles on the user side shall be split fabric magnetic/fabric tack able/white board/prelaminated / plain metal along with split fabric magnetic/fabric trackable/white board/prelaminated/ plain metal. Intermediate blocks shall be given in fabric/DL + Fabric/DL finish. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it shall be carried up to the panels through concealed conduits inside the blocks. HALF SCREEN WITH FRAME - at intermediate position between 2 people and at the end above worktop in clear glass/fabric tack able /laminate/white board finish. Side panels or legs shall be 25 mm thick prelaminated particle board with flat PVC lipping edge banding considered only on the open end conditions or metal powder coated legs at the end and shared condition. System shall have 120 mm high powder coated standalone panel legs to give the system an elevated look. Work surface shall be 25 mm thick prelaminatedparticle board with flat PVC lipping edge banding of size 1500 mm w1 X 1500 MM w2 x 600 mm d. Pedestals with or without legs shall have flat metal front, free standing central locking of size 390 mm w x 435 mm d x 646 mm height 3dr = 2box+1file. CPU trolley - with castors. KBPT with mouse tray - plastic/metal/articulated. The work shall be carried out as per guidance and instructions received from engineer in charge. The product shall be Green guard BIFMA LEVEL, AIOTA, GRIHA, SCS IAQ, GREENPRO certified. OEM shall be ISO 9001:2015, ISO 14001:2015 & ISO 18001:2007 certified.
268	Providing and placing in position panel & tile based modular workstation. Size of worktop shall be 1800mm W x 800mm D with partition thickness of 52.4 mm thick and height - 1200 including powder coated aluminum trims. Work top shall be pre laminate particle board ,`below the work top is also pre laminate particle board. The tiles on the top most frames shall be glass writing board/ clear glass tile. Bottom tiles shall be of Plain metal/ fabric magnetic / fabric / laminated /pre-laminated. The panel thickness comprises of 38mm (35 mm Minimum) thick paper honeycomb + 3.6mm thick line gap each side + 3mm MDF on each side + 0.6mm decorative laminate or fabric on both sides. Size of ERU shall be 1200mm W x 450mm D x 1200mm H .The uprights and horizontals shall be made of aluminum extrusion having average wall thickness of 1.2 mm & powder coated with epoxy- polyester powder. Particle board framing shall be used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks shall be located in the mid segment of the panels and can be provided with cutouts for mounting switch boxes (above or below the worktops). Top tiles must have variety of combinations. The fins along the depth shall be 22.8mm thick. Work surface shall be of 25 mm thick prelim particle board with flat PVC lipping edge banding. Brackets shall be made from 2mm thick CRCA steel. Pedestals with legs shall have flat metal front, free standing central locking of size 390 mm w x 435 mm d x 646 mm height 3dr = 2box+1file. The work shall be carried out as per the instructions and guidance received from engineer in charge. The product shall be UL Green guard, BIFMA Level 3 certified. OEM shall be ISO-9001:2015, ISO-14001:2015, ISO-45001:2018, BIFMA and AIOTA certified.
269	The overall size shall be 1200 x 450 x 1950 (WDH) mm. Top shall be made up of 18mm thick pre laminatedparticle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. Locking faciltity should be provided for safe storage of documents. The prelaminated board used shall be of E1 norms
270	Providing and placing ALL WOOD SLIDING DOOR UNIT (SDU). size- 1200Wx1190Hx450D. Construction & Material shall be in Knockdown construction. Twin door with self-closing hinges of Wood shall be made from18mm Thick Pre-Laminated Board. Aesthetically appealing recessed plastic handle shall be fitted on wooden Doors.3-point locking mechanism shall be fitted on Wooden Door. Height wise Adjustable Shelf Mounting shall be provided. Wooden Top shall be made from Pre-Laminated Board of 25 mm thick. Skirting of 125 mm High shall be provided. Leveler Screw type adjustable Leveler with plastic base height shall be provided. Back Panel and Sides of the storage units shall be made of 18mm thick Pre-Laminated Particle Board. All partitions and side panels shall have levelled screws for adjustment in case of Uneven floor to take care of +/- 10mm of uneven flooring. The work shall be carried out as per guidance and instructions received from engineer in charge. OEM shall be ISO-9001:2015, ISO-14001:2015, ISO-45001:2018, BIFMA and AIOTA certified.
271	Providingin place of main table with overall size of table 1650 x 1650 x 750mm. The main table shall be of size 1650 x 750 x 750mm. The side unit shall be 900 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.
272	The Back Unit shall be of dimensions 1650 x 500 x 750mm. It shall be made of 25mm thick MDF– one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security.
273	The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm.The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. The neckrest assembly consists of upholstered neckrest inner(material-poly propylene) with moulded polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck rest cover. neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Heightfrom ground - min 109.3 to max 124.4 cm. Seat height - min 45.5cm to max 55.5cm.Dimensions tolerance / variations shall be within +/- 1 cm.
274	The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio Synchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm.The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from pedestal below. Heightfrom ground - 99 cm. Seat height - 49 cm.Dimensions tolerance / variations shall be within +/- 1 cm.
275	Supplying and placing in position Canteen table of the following specifications. 6 Seater PU Coated size shall be1734 Width mmx 1175 Depth mmx 750 Height mm.Top shall be 25 mm thick base material shall be 25 mm MDF board . On top PU painting of minimum 2H hardness with 75% glass as per color chart .Combination color graphics on the centre . Brown Laminate on bottom specially profiled edges for comfort . The Understructure shall be having bend pipe structure of MS powder coated . Pipe dia 38 mm , 2 mm thick and it shall be fitted with top by SS machine screws . Legs shall be of MS powder coated and 38 mm dia. pipe legs are fixed with inderstructure and table top . Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during stacking .
276	The seat and Back are made up of injection moulded high impact strength PolyPropylene polymer compound with indoor grade UV resistance. Seat size shall be 52.5cm x 53.2cm. Back size shall be 51.6cm x 40.5cm. The tubular welded frame is made of dia. 2.22cm x 0.12cm and 3.5cm x 1.5cm x 0.12cm stainless steel 202 grade tube. The rubes are buff polished to give shiny finish. The shoes and Amrest are made of high impacy strength PolyPropylene polyemr compound with indoor grade UV resistance and pressed and press fitted with tubular frame. The overall dimensions of the chair shall be 52.4cm x 55.8cm x 84.5cm. The seating height shall be 45.0cm.
277	Overall Size : Width:166cm Depth : 97.5cmHeight : 93cmSeating Height : 46cmUpholstery: Material : Fabric PVC ,Shade : Ash Grey , Thickness : 1 mmBreaking Load (N) : Warp 1327 ,Weft 1228, Elongation at break (%) : Warp 27.5 Weft 34.6 .Colour Fastness to Rubbing (Dry/Wet) (scale 1- 5) :FrDarmy e= :4 Wet = 4 . Material : Combination of plywood and pine Wood. Plywood thickness : 12 mm (moisture resistance and termite free) Pinewood cross section ( without knots) .Moisture content : 10 -12 %Foam .Seat :Material : Slab stock foam , Density : Base 28 kg/m3 and super soft 32 kg/m3 at top .Back :Material : Slab stock foam, Density : Super soft foam of 32 kg/m3 .Mechanism at Headrest : Hittech make which can be adjusted at three levels . Webbing:Elastic belt with pocket spring of diameter 2mm .Legs : MS pipe with metallic powder coated
278	Overall size of 1200mm(L)x594mm(D)x411mm(H).Ultra-modern combination of wood and glass, specifically shaped and engineered to give it stability. Now, your drinks won’t spill as easily in case of accidental tugs and yanks.• The Wenge finish of the coffee table is done with utmost care, making it a posh addition to your space.• Has multiple compartments to store books, magazines, or place decor items. A hidden compartment within can be used to store utility bills and keys.
279	Overall size of 600mm(L)x600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy, compartmentalized storage.• Tabletop of durable, toughened glass with a digitally back-printed Skyline pattern creates a sleek, modern look.• A strong, knockdown construction built for longevity.
280	Overall Size :Width: 137cmDepth : 92cm Height : 89cm Seating Height : 47.5cm THREAD : Nylon . Material Handling Data Sheet (MSDS) for GlueStandard of Plywood used: IS 303 Commercial Plywood , Thickness 12mm
281	Overall Size :Width: 92cmDepth : 92cm Height : 89cm Seating Height : 47.5cm THREAD : Nylon . Material Handling Data Sheet (MSDS) for GlueStandard of Plywood used: IS 303 Commercial Plywood , Thickness 12mm
282	Overall Size : Width : 120cmDepth : 60cm Height : 36.7cm Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Drawer bottom is made of .9 mm thick prelaminated particle board .Drawer front is made of 18 mm thick PU painted MDF . Legs : Rubber wood . Hardware : Hettich . Construction : Knock down .Finish :All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band. PU lamination is high gloss in Ecru shade .Packets : 1 nos . Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Hardware : Hettich . Construction : Knock down .Finish : • All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band . PU lamination is high gloss in Ecru shade .Packets : 1 nos
283	Overall Size : Width : 60cmDepth : 60cm Height : 49.8cm Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Drawer bottom is made of .9 mm thick prelaminated particle board .Drawer front is made of 18 mm thick PU painted MDF . Legs : Rubber wood . Hardware : Hettich . Construction : Knock down .Finish :All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band. PU lamination is high gloss in Ecru shade .Packets : 1 nos . Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Hardware : Hettich . Construction : Knock down .Finish : • All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band . PU lamination is high gloss in Ecru shade .Packets : 1 nos
284	Electrical BOQ
285	MAIN PANEL & DISTRIBUTION BOARD
286	Supply,installation,testing and commissing of 3phase and neutral 415V 4 wire free standing floor mounted indoor MV panel made out of 14 SWG sheet after seven tank process and painting with epoxy powder coating MV electrical panel shall be dust and vermin proof ,hinged and locable doors.The panel shall consist of suitable rating TPN bus barat the rating of 0.8A /SQMM Supported by DMC/SMC insulator and color coded with heat shrinkable sleeves. Metering shall be provided as specified .The panel shall have short circuiting with standing capacity of minimum 36KA and consist of the switch gear as mentioned below .The panel shall got fabricated from manufacturer with CPRItest certificate .The panel shall be mounted on U channel including supply and fixing of the same.(including Capacitor banks)
287	Incoming
288	250 Amps 4P 36KAOn Load change over switch. -1No.
289	250 Amps 4P 36KAMCCB. -1No.
290	Spreaders-1Set.
291	Extended Rotary Operating Mechanism.-1Set
292	Metering
293	Digital V A F Meter with built in Selector Switch, CTs, CT shorting links, R/Y/B LED indicating lamps and control SP MCBs.
294	OutgoingSection
295	63 Amps FP MCB_C curve -6Nos.
296	80 Amps FP MCCB -1No.
297	125Amps 4P25KA MCCB-3Nos.
298	8 Step Automatic Power Factor Correction Relay (Digital)_1 No
299	63 Amps TP MCB -3Nos.
300	32 Amps TP MCB -4No.
301	10 kVARAC3 Duty Contactor with 220 V AC Coil_3 Nos
302	5 kVARAC3 Duty Contactor with 220 V AC Coil_4 Nos
303	ON / OFF LED Indicating Lamps _7Set
304	Start / Stop Push Buttons_7Set
305	A/M Selector Switch_1 No
306	Control S/P MCB (2/4 A)_7 Nos
307	Neutral Links_7 Nos
308	Control Blocks_7 Nos
309	Enclosure, 300ATPN 415V 50Hz Electrolytic grade AL conductor Busbar with 100% neutal& Non adhesive PVC insulated heat shrinkable sleeves, Internal Wiring, Terminals, etc.as required._1Set
310	Supplying the following MCCBs in sheet steel enclosure. For Ups Input & Output
311	125A 4P MCCB in sheet steel enclosure surface mounted on the wall along with incoming & outgoing Cable Box, suitable for Termination of Aluminium / Copper Cable. (For Ups Input )
312	UPS Output panel
313	Incoming
314	125 A 4P Onload changeover switch in sheet steel enclosure surface mounted on the wall along with incoming & outgoing Cable Box, suitable for Termination of Aluminium / Copper Cable.
315	OutgoingSection
316	80 Amps FP MCCB -3No.
317	Spreaders-3Set.
318	Extended Rotary Operating Mechanism.-3Set
319	Enclosure, 200ATPN 415V 50Hz Electrolytic grade AL conductor Busbar with 100% neutal& Non adhesive PVC insulated heat shrinkable sleeves, Internal Wiring, Terminals, etc.as required._1Set
320	DISTRIBUTION BOARDS.
321	Supply , installation ,testing and commissioning of \"MCBdouble door Distribution Boardsdust andvermin \"proof protectedand AC supply operation including incomingMCB/ELCB/RCBO as per specifications and required capacity Neutral bar and Earth Terminal complete as requiredand installed in concealed in wall after necessary chase cutting with finishing /surface on wall including all fixing materials required.
322	20Way TPN MCB DB with 125A 4P MCCB(36KA) as incoming and 60 nos (6-32A)SP MCB as outgoing.(For UPS DB)
323	16Way TPN MCB DB(Vertical type) with 80A 4P MCCB(25KA) as incoming and 48 nos (6-32A-10KA )SP MCBas outgoing.(For LPDB)
324	12Way TPN MCB DB(Vertical type) with 63A 4P RCCBas incoming and 36 nos (6-32A-10KA )SP MCBas outgoing.(ACDB)
325	8Way SPN MCB DB with 40A DP RCCBas incoming and 8 nos (16-20A-10KA )SP MCBas outgoing.(For Server)
326	CABELS / MAINS
327	Supply ,laying,testing and commissoningof 1100V grade armoured cable having sector / circular shaped aluminium / copper conductor PVC insulated cores under groundPVC tape wrapped inner sheathed, GI strip / wire armoured and overall extruded PVC sheathed confirming to IS: 1554, laid on wall or ceiling using GI clamps and spacers as per route shown at site and further as directed by Engineer-in charge
328	185 Sq.mm 3 1/2 coreAluminium cable
329	35 Sq.mm3 1/2core Aluminium cable
330	1 6Sq.mm4 core copper cable
331	25Sq.mm4 core copper cable
332	4 Sq.mm 3 core Copper cable (For AC Units)
333	Supply & fixing of end termination for above mentioned cables including compressed type brass glands, crimping type coperlugs, insulation tape etc. as \"required complete with earthing of glands in following sizes
334	185 Sq.mm 3 1/2 coreAluminium cable
335	35 Sq.mm3 1/2core Aluminium cable
336	1 6Sq.mm4 core copper cable
337	25Sq.mm4 core copper cable
338	4 Sq.mm 3 core Copper cable (For AC Units)
339	WIRING
340	Point wiringfor light point /Fan/Exhaust Fan point/ call bell point using 2 runs of1100 V grade 1.5 sqmm & one run of 1.5 sq.mmFRLS insulated multistranded copper wires,in & including 25 mm dia , MS conduit surface/ concealed in wall / ceiling conferming to IS 732 including all accessries such as junction boxes , conduit bends, elbows and ceiling rose , and anodised GI switch box with modular switch ,modular plate and the box covered with front plate
341	One light pointcontrolled by one 6A switch
342	Secondary light pointcontrolled by same switch
343	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
344	2x1.5sqmm+1x1.5sqmmearth wire
345	2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
346	2 X 4 sq. mm + 1 X 4 sq. mm earth wire
347	Exhaust fan point including of ceiling rose near fan.
348	Wiring for twin controlpoint wiring using1.5 sqmm copper conductor FRLSPVC insulated copper conductor cable drawn through 25 dia MS conduit laidin surface/concealed over false ceiling or in slab/wall chases including ,2way modular switches,modular plate ,suitable GI box and earthing the point with 1.5 sqm FRLS PVC insulated copper conductor single core cable as required
349	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
350	5/6 A switch
351	15/16 A switch
352	3 pin 5/6 A socket outlet
353	6 pin 15/16 A socket outlet
354	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
355	3 Module (100mmX75mm)
356	6 Module (200mmX75mm)
357	Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.
358	3 Module
359	6 Module
360	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
361	Supply and fixing of following sizes ofMS conduit along with accessories in surface /recessincludingpainting in case of surface conduit,or cutting the wall and making good the same in case of recessed conduit as required
362	25mm dia
363	Supply and fixing of 3 nos. 6A socket with 6M modular GI box, base plate and cover plate below worktop, along with 1no. 6A socket, 1 no. 6A switch and 1 no. 16A switch(for 3 nos. sockets) in 4M modular GI box, base plate and cover plate above worktop complete as per drawings and instructions of engineer in charge.
364	LIGHTING FIXTURES
365	SITC of 2\"X2\" recessed mounted Luminaire with Maximum 36 Watt with Lumen output of 3600 lumen. The product should be SMD based and have non integral isolated driver with 2KV inbuilt surge protection.THD<10%, PF >0.9,Product should have life class of 50K burning hour at L70 B50 parameter, Luminiare operating temp 0 D to 45D. Internal wiring should have teflon coted multi strand wires and external wire should have PVC coated multistrand wires.
366	SITCof 15W Recess type IP40 LED Round shaped Downlighter fitting made of Aluminum Pressure die cast housing duly powder coated and opal diffussser, having CCT range 5700K,system efficacy ≥ 110lm/W (not LED Chip efficacy), CRI≥80, SDCM < 3, Mimimum System Ouput ≥ 1650 Lumens, useful life of 50,000 hrs at L70& driver having isolated constant current topology with PF ≥ 0.95, THD<10%, Operating voltage range: 100-265V AC and Surge Protection of 2.5KV suitable for installation on the false ceiling including connection with 3X1.5 sq.mm FRLS PVC insulated copper conductor,earthing etc complete as required. The LED fitting must have the embossed/engraved logo the approved make (fittings with stickers shall not be approved). BIS Certificate issued to the approved make along with LM79 report from NABL lab must be shared at the time of supply. Cut-out dimension: ø145 ± 2mm, Fixture dimension: ø159 X 39mm (±2mm), Weight: 0.335gm
367	SITC of Extruded Aluminium suspended/ surface mounted 36Watt, 4000 lumen LED batten with PC Diffuser and Spring Steel Clamps for Surface Mounting arrangement. Driver THD<15%, PF >0.9,with 2KV inbuilt surge protection. Internal wiring should have teflon coted multi strand wires and external wire should have PVC coated multistrand wires.
368	Supply, Installation, Testing and Commisioning of linear/ curvilinear suspended /surface/Recessed High Efficiency16-18W per meter Suspended LED Channel, Body made of Aluminium andOpal Diffuser with homogeneous light distribution and without hotspots. Color Temperature 3000K/4000K/5700K, CRI>80, IP20, IK04, operating voltage range 140-270Vac, operating temperature -10° to 45°C, PF>0.95, THD<10%, product efficacy>110lm/W, SDCM<5, L70B50@50000hrs, LED binning as per ANSI Bin C78.377A, 110° shall be luminaire beam angle, drivers efficiency >86%, internal surge protection of >3.5kV, The manufacturer shall provide LM79, LM80, TM21, Photoboilogical safety as per IEC 62471, RoHS complaint, BIS both for fixture and drivers. The cost to include all connectors and accessories required to install in the lights in formations as per approved drawings and instructions of engineer-in-charge/ architect.
369	Providing & Fixing Coverings (Ceiling & Wall) Made out of Polyester Kintted fabric Coated with polyurethane (PU). The Fibric width 2m,3m,4.1m,&5.1m with Weight of 200gm/m^2. thickness of 0.3mm. The appearance of fabric is Matl. smooth and uniform with blance color and ligth transmission of 50%. The tear strength of fabric should be accordance to CH. 4.5daN; TR: 6.5 daN. The fire Railing should be accordance to B-S1, do. The febric should be humidity ressistant and free of cercinogenic subtance (CMR) or volatile organic compounds (VOC\"s). At lableing in accordance with the French decree no, 2011- 321, Oeko -Tex standar100 certified. The fabric should be paintabe/printable with approved manufacturer guidelines with 10-year manufacture guarantee. the Installation of fabric should be dry installation 7done at room tamperature using CLIPSO PVC, ASB tension profiles P.CC/P-C10QS/P-C11QS/P-CCB022/P-B1/P-CC1P. There are several lighting options available including various LED options and fluorescent lighting. When Positioned properly. LED Lighting modules provide an even light flow, casting no shadowns or hot spots. coverings are used for a variety of aluminated applications, including but not limited to walls, ceiling, lightboxs or wall frames. coverings can enhance your door with a variety of spacial effects fiber optics or changinglights, or create a statement piece incorporating custom printing. The cost of electrical cove light fixtures is included in the same.
370	Providing & Fixing Heavy Duty 4 Blade, 15\" Exhuast Fan complete with all hardware and connectors etc., as per the direction of the engineer In charge
371	SITC of 7W Recessed FixedLED Spotlight, Body made of high grade di-cast Aluminium, System Power 7W,230V, CRI>80,Dia- 68mm X 65 H mm, cut out Dia 60mmcolor temperature 3000K/4000K/5700K, Hi- Precision optics with Beam Angle 15°/24°/36°, IP20, IK02, operating voltage range 140-270Vac, operating temperature -10° to 45°C, PF>0.95, THD<10%, product efficacy>100lm/W, SDCM<5, L70B50@50000hrs, LED binning as per ANSI Bin C78.377A, drivers efficiency >86%, internal surge protection of >2kV. The manufacturer shall provide LM79, LM80, TM21, Photoboilogical safety as per IEC 62471, RoHS complaint, BIS both for fixture and drivers.
372	PASSIVE NETWORK SYSTEM
373	Supply, Installation, Testing & Commissioningof LED 24 Port loaded Cat 6 Jack Panel, Staggered 24 Port panel with All port LED in 1U Rack Unit, Copper AlloyedContactMaterial,EIA568A/Bwired,PC+ glass fiber, UL 94V-0, black color, Front Port Labeling, 22-24 AWG WireAccumulation etc.complete as required.
374	Supply, Installation, Testing & Commissioning of dualfaceplatehavingprovisionforoneI/Oalong withspringtypeshutterfordustproof,madeof ABS PVC plastic etc. complete as required.
375	Supply, Installation, Testing & Commissioningof single face plate having provision for one I/O along withspringtypeshutterfordustproof,madeof ABS PVC plastic etc. complete as required.
376	Supply, Installation, Testing & Commissioningof CAT 6Information Outlet, Universal label permits T568A or B wiring, UL® Listed, meets all TIA and ISO requirements Complete in all respect as required by the site etc. complete as required.
377	SupplyinganddrawingofUTP4pairCAT6LAN Cableintheexistingsurface/recessedSteel/PVC conduit as required.
378	1 run of cable
379	Supply, Installation, Testing & Commissioningof CAT6PatchCordLSZH1Mtr,4pair26AWG stranded copperwire,Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Listed, meets all TIA andISOrequirements.Completeinallrespectas required by site completion etc. complete as required.
380	Supply, Installation, Testing & Commissioningof CAT6 PatchCordLSZH2Mtr,4pair26AWG stranded copperwire,Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Listed, meets all TIA andISOrequirements.Completeinallrespectas required by site completion etc. complete as required.
381	Supply,Installation,Testing&Commissioningof6 Core Armoured single Mode Fiber optic cable, Central Lose Tube With Jelly Compound, Corrugated steel tape armoured, Heaving 1300 nm Wavelength in the existing surface/ recessed Steel/ PVC conduit etc. complete as required.
382	Supply,Installation,TestingandCommissioningof singleModefiberSC-LCDuplexpatchcordof2 Mtrs.forGigabitConnectionbetweenPatchPanel and Switch etc. complete as required.
383	Supply, Installation, Testing & Commissioningof Horizontal cablemanageretc. completeas required.
384	Supplyingandfixingoffollowingsizesofmedium classPVCconduitalongwithaccessoriesin surface/recessincludingcuttingthewalland making goodthe same in case ofrecessedconduit as required.
385	20 mm
386	25 mm
387	Supply, Installation, Testing & Commissioningof LED 24 Port loaded Cat 6 Jack Panel, Staggered 24 Port panel with All port LED in 1U Rack Unit, Copper AlloyedContactMaterial,EIA568A/Bwired,PC+ glass fiber, UL 94V-0, black color, Front Port Labeling, 22-24 AWG WireAccumulation etc.complete as required.
388	Supply, Installation, Testing & Commissioningof CAT6PatchCordLSZH1Mtr,4pair26AWG stranded copperwire,Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Listed, meets all TIA and ISO requirements etc. complete as required.
389	Supply, Installation, Testing & Commissioningof CAT6PatchCordLSZH2Mtr,4pair26AWG stranded copperwire,Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Listed, meets all TIA and ISO requirements etc. complete as required.
390	Supply, Installation, Testing & Commissioningof CAT6InfornmationOutlet,Universallabelpermits T568A or B wiring, UL® Listed, meets all TIA and ISO requirements etc. complete as required.
391	SupplyinganddrawingofUTP4pairCAT6 LAN Cableintheexistingsurface/recessedSteel/PVC conduit as required.
392	1 run of cable
393	Supply,Installation,Testing&Commissioningof6 Core Armoured single Mode Fiber optic cable, Central Lose Tube With Jelly Compound, Corrugated steel tape armoured, Heaving 1300 nm Wavelength in the existing surface/ recessed Steel/ PVC conduit etc. complete as required.
394	Supply,Installation,TestingandCommissioningof singleModefiberSC-LCDuplexpatchcordof2 Mtrs.forGigabitConnectionbetweenPatchPanel and Switch etc. complete as required.
395	Preparation of complete set of MEP drawings including details. A qualified professsional for the purpose shall be appointed after due appproval from Engineer In Charge.
396	Supply, Installation, Testing & Commissioningof Horizontal cablemanageretc.completeas required.
397	Supplyingandfixingoffollowingsizesofmedium classPVCconduitalongwithaccessoriesin surface/recessincludingcuttingthewalland making goodthe same in case ofrecessedconduit as required.
398	20 mm
399	25 mm
400	CABLE TRAY.& RACE WAY.
401	Supply, fabrication and fixing of steel frame work in position for cable tray/Panels fabricated out of 10 mm dia GI rods, ISA-40 MS angle iron, ISMC-50 channels, flats etc.complete with providing of Anchor fastners and all necessary hardwares as required for fixing, including cutting, bending, welding, drilling, bolting etc. as per design as required and painted with one coat of primer and two coats of enamel paint of approved shade.
402	Supply and fixing of Perforated type 2mm thick Hot dip Galvanised G.I. cable tray of following sizes complete with bend/tee joints, coupling plate & nuts bolts etc. as required for fixing and including the cost of providing loop earthing with 2 nos. 50 mm x 6 mm GI earth strips complete as per specifications, as required and as below.
403	150 mm wide 50 mm depth.
404	300 mm wide 50 mm depth.
405	GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only)
406	Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway with internal partition/compartmentized of the following sizes including providing removable 3 mm thick GI cover, knock out holes and fixing accessories earthing with 8 SWG copper earth wire completeas required including floor supports, bends, access boxes, tap off boxes and cross over as per specification and site requirement. (overhead / wall mounted recovery & function boxes shall be 1.6 mm thick)
407	300 mm widex 38 mm deep raceway
408	225 mm widex 38 mm deep raceway
409	150 mm widex 38 mm deep raceway
410	100 mm wide x 38 mm deep raceway
411	Fabricating, supplying & installation on surface/ recess2.0 mm thick factory fabricated GI Sheet raceways height 50 mm and of totally enclosed with 2 mm thick covered. Two lengths of raceways and junction box shall be joined together to make it dust proof. Chipping and removing screed to install the junction boxin floor, including removal and disposing of debris / fixing in ceiling along with suspender and accessories as per instruction of Engineer in charge.
412	350 mm (wide) x 350 mm (length) X 50 mm (height)
413	250 mm (wide) x 300 mm (length) X 50 mm (height)
414	200 mm (wide) x 200 mm (length) X 50 mm (height)
415	150 mm (wide) x 150 mm (length) X 50 mm (height)
416	UPS SYSTEM
417	20 kVA UPS with 15 minute backup
418	Supply, unloading, shifting, installation, testing & commissioning of micro processor controlled following rating UPS capable of operating in parallel redundant mode so that if any one UPS fails the other can supply 100% load, IGBT based rectifier to achieve input THDI < 4% and input power factor of greater than 0.99 at 100% loading with 3 level Inverter Topology. True Online Double Conversion (VFI as per IEC 62040-3) UPS usingPWM IGBT technology , 3 Phase input and 3 phase 415 V output UPS system; andcomprising of the following complete as required and as per specification:
419	20kVA
420	Fully rated Rectifier cum charger unit and 100% rated Invertor unit Integrated in UPS module.
421	Fully rated Inbuilt static switch at the inverter output and 100% rated Inbuilt static switch at the static bypass line integrated in UPS module.
422	Web-enabled Monitoring and Management through SNMP protocols for multi-OS environments with below features.
423	Giving notifications like e-mail, paging notification, broadcast notification, battery replacement notification, run event-based scripts.
424	Event logging, data logging and action logging (with date, time, description of fault and event).
425	Fully rated Inbuilt Maintenance Bypass Switch for the continuous operation of the load during maintanance.
426	Local notification through audible alarm.
427	Fully rated Battery Circuit Breaker with under voltage coil & deep discharge protection to the batteries.
428	One time cost of replacement of PCBs to be considered, in case conformal coated PCBs are not available . (Vendor to specify the cost considered)
429	Battery Banks comprising ofValve Regulated Lead Acid Sealed Maintenance Free batteries of minimum 5years design life to provide 15 minutes backup at 20kVA ,0.9PF, ECV=1.7V with each UPS. Minimum VAH required with each UPS 11232 VAH .The batteries shall be installed on shelves of rack for quick replacement and servicing. The temperature sensor shall be provided in the battery sectionfor temperature compensatedcharging. The bank of batteries shall comprise of required numbers of batteries connected in series.Vendor to provide complete details of make of Batteries, ampere hour ratings, no. of Batteries, Expected life, Final discharge voltage, Nominal float voltage, Battery recharge time & configuration of back up time, Battery sizing Calculations
430	Supply, unloading, installation, testing & commissioning of open type MS racks including top fully cover to protect from falling object to house SMF batteries for 30 kVA UPS system along with suitable interconnecting links, moulded case circuit breaker having Ithermal, Imagnetic & automatic U/V trip mechanics for Battery Banks etc. complete as required & as per specifications.
431	UPS Testing with External Load Banks (To be provided by vendor) for 8 hours at full load shall be included in the offer incase Phantom Loading feature as specified in the data sheet is not available in the UPS.
432	Supply, laying, testing & commissioning of flexible single core copper cablefor interconnections between UPS to UPS, UPS to batteries( 10 m) , complete as required for each UPS.
433	Supply, Installation, Testing and Commissioning of 5KVA True Online double conversion VFI technology, High Frequency PWM using IGBT technology, 1 phase AC Input & 1phase AC Output UPS. Input range should be 180 VAC-260 VAC. Provisions for maintenance by pass switch module. Microprocessor based LCD display &indication for various electrical parameters.LED indication with alarm for major fault.BATTERY BANKSupply, Installation, Testing and Commissioning of 12V Monoblock suitable size and nos ofsealed maintenance free batteries supportingfor 5KVA UPS System for providing 90 minutes back up time with each UPS at full load with interconnecting leads, mounting racks/stands for stacking the
434	batteries, along with Battery Circuit Breaker, Connection, Interconnections, and standard accessories etc. complete as reqd.1 Set =One Complete UPS + One Battery Bank of 90 minutes backup.
435	ACCESS CONTROLSYSTEM
436	Supply, Installation, Testing & Commissioning of SCOSTA Based with 1 SAM Slot 4 Door Intelligent Access Control Controller vthrough Master/Slave Architecture(optional), TCP/IP, IPV6, SNMP V3 ,200,000 card holder capacity, 200,000 transactions buffer, 32 acess levels per card holder, OSDP Secure Channel, Supports 2 Doors, 4 Readers (OSDP) per controller (IN/OUT Reader Combination), Integration with Fire Alarm System, Integration with Fire Alarm System, Open Architecture - supports Multiple OEM Software, Supports downstream readers via cable, UL Listed. as per specifications of this tender etc complete as required and directions of Engineer-in-Charge.Controller shall be installed inside ELV rooms & Utility Buildings including allaccessories complete as per specification/drawings and as directed by Engineer In Charge.
437	Access Control System Software :-EnterpriseversionServersoftwarewithTimeattendancemanagementsystem asperspecificationwithclient version.Supply,installation,testingand commissioningofAccessControlSystemServerSoftwareconsistingofAccessControlsystem,Visitormanagementwithallemployeevisitorlicense, ElevatorControl,GuardTour Management , Mantrap, Alarm Document, Alarm management, 3 client License, Graphical layout, Card Enrolment, Badge designing..All these along with high end security features consist in single package with an option to integrate with CCTV sub system (License based ), VAPT and ISO Certified as per specifications of this tender etc complete as required and directions of Engineer-in-Charge.
438	Supply, Installation,Testing & Commissioning of Smart Card Reader 13.56 MHz Credential as per specification Card Range:7 to10cm suitable for mounting on metal surface/metal frames/ wooden frames / wall or as required based on site conditionsincludingallaccessoriescompleteasperspecification/drawings andasdirectedbyEngineerIn Charge.In case of SAM based SCOSTA Smart Card Reader - Minimum 1 SAM slot shall be provided.
439	Supply, Installation,Testing & Commissioning of Biometric - cum- Smart cardReader supporting up to three-factor authentication. Supportcard/biometric fingerprint,card/PIN or card/fingerprint/PIN.13.56MHz Credential Compatibility.OperatingTemperature-10°to50°C;OperatingHumidity:5% to95%relativehumiditynon- condensing. ANSI-378 template stored on smart card credentialand verified on reader.Suitable formounting on metal surface/metal frames/ wooden frames / wall or as required based on site conditions including all accessories complete as per specification/drawings and as directed by Engineer In Charge.Certification : BIS, CE, FCCIn case of SAM based SCOSTA Smart Card Reader - Minimum 1 SAM slot shall be provided.
440	OEM Programmed Unprinted 37 bit Smart Cards.AES-128 bits cryptographic algorithms for data protection. Supports ISO/IECstandards:7810, 7816 and contactless cards (14443 A) complete as per specification and as directed by Engineer In Charge.:-In case of SAM based SCOSTA Smart Card Reader - Smart card must haveSCOSTA CL OS and 64KB of memory\"
441	Supply,Installation,TestingandCommissioningof AccessControlServerwithWindows10ProOS, SQL Databasealong with MS.Office Intel® Core™ i7- 10700(16MBcache,8cores,16threads, 2.90to4.80 GHz Turbo, 65W), 8 GB, 1 x 8 GB, DDR4, 3200 MHz, Intel®Integrated Graphics, 3.5 inch 1TB 7200 RPMHardDiskDrive,64MBcache,4GBAGP GraphicsCard,Windows10OS Professional64bit oraboveetc, KeyboardandMouseasperthe requirement of the surveillance systemcomplete
442	Supply,Installation,TestingandCommissioningof Electro Magnetic Lock, Lock Status Monitoring through LED,Low Energy Consumption, Electroless Nickel (EN) Plated Armature Plate, 12/24V Selectable, Anodized Aluminium Housing, CE Compliance, Ideal for alldoor type.
443	Single leaf Door
444	Double leaf Door
445	Providing&LayingofArmored,PVCinsulatedand PVC shiethed AB Copper Shielded Flexible Cable on existing wall surface etc. complete as reqd.
446	8 C x 0.75 Sq. mm
447	4 C x 0.75Sq. mm
448	Supply,Installation,TestingandCommissioningof Green ABS plastic Emergency glass break Units etc. complete as reqd.
449	Supply,Installation,TestingandCommissioningof Magnetic contacts for all access doors (one for each single leaf door and two for each double leaf doors) etc. complete as reqd.
450	SupplyinganddrawingofUTP4pairCAT6LAN Cableintheexistingsurface/recessedSteel/PVC conduit as required.
451	1 run of cable
452	Supplyingandfixingoffollowingsizesofmedium classPVCconduitalongwithaccessoriesin surface/recessincludingcuttingthewalland making goodthe same in case ofrecessedconduit as required.
453	20 mm
454	FA & PA SYSTEM
455	Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications.
456	Two Loop Panel.
457	Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.
458	Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.
459	Supplying, installation, testing & commissioning of addressable manual call point complete as required.
460	Supplying, installation, testing & commissioning of addressable strobe complete as required.
461	Supplying, installation, testing & commissioning of fault isolator complete with base as required.
462	Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.
463	CABLES & ACCESSORIES FOR FAS :
464	Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.
465	SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES :
466	Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.
467	Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required.
468	Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required.
469	CABLE & ACCESSORIES FOR PA SYSTEM
470	Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.
471	speaker cable Single pair, 2-core, 1.5 sqmm
472	Supply and fixing of following sizes ofMS conduit along with accessories in surface /recessincludingpainting in case of surface conduit,or cutting the wall and making good the same in case of recessed conduit as required
473	25mm dia
474	IP BASED CCTV SYSTEM
475	Supply, installation, testing and commissioning of IR & IP Based dome type indoor coloured fixed camera with of 1/3\" CCD,540 TVL, Sensitivity @ 30 IRE: Color 0.5Lx/Night Sense 0.18 Lx, AWB / BLC / AGC /Auto Black, 2.6 to 6 mm vari-focal lens Auto Iris, 12VDC/24VAC for indoor application, complete in all respects as per specifications as per engineer in charge.
476	Supply, installation, testing and commissioning of DVR-20-CH, 400/480fps display, 400f/480ps recording, H.264, Recording @704x480 (100/120ips)/ 704x240 (200/240ips)/ 352x240 (400/480ips), 8Audio In/ 1 Out, 16 Alarm In, 4 Relay Out, Network Port available forRemote View S/W with transmission up to 120 IPS @ 352x288 PAL, along with 3 TB HDD, complete all as specified with 230VAC power supply complete in all respects as per specifications as per engineer in charge.
477	Supply, installation, testing and commissioning of High Resolution 32 inch LCD colour TV monitor with on screen adjustment menu, durable metal cabinet etc.complete in all respects as per specifications as per engineer in charge.
478	Supply and fixing of following sizes ofMS conduit along with accessories in surface /recessincludingpainting in case of surface conduit,or cutting the wall and making good the same in case of recessed conduit as required
479	25mm dia
480	Supply and fixingof RJ45 Connector
481	Supplying and fixing in position GI box for data outlet suitable for fixing of RJ 45 face plate complete as required.
482	Supply & fixing of Plug in type RJ45 computer data outlet in existing faceplate/ GI Box in wall/furniture/floor complete as required.
483	Supply & Fixing ofSingle Faceplate, Single Port square plate having spring shuttered front access for preventing ingress of dust, dimension as per commercially available modular office furniture.
484	Supplying and drawing of CAT 6A U/UTP cable, white jacket, 4 pair LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
485	HVAC - DUCTING
486	Replace AHU canvas connections
487	Supply, Installation, TestingBalancing & Commissioning of G.S.S square/ rectangular ducting complete with gaskets, elbows, splitters, vanes, supports adjustable dampers, etc. as per drawings and as required for dehumidified air distribution of following thickness as per approved working drawings and requirement .
488	Thickness 0.63 mm sheet
489	Thickness 0.80 mm sheet
490	Thickness 1.00 mm sheet
491	Supply and fixing of external thermal insulation on supply air ducts with 19mm thick chemically cross linkedclosed cell polythene (XLPE) fire retardant grade insulation of density not less than 30kg per cum in single layerwith factory laminationof 30 micron aluminium foilor 19mm thick insulation as per CPWD specifications
492	Suply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets,nut,bolts,screws linkages,flanges etc. as per specifications
493	Supplying, fixing, testing & commissioning of powder coated extruded aluminium section supply air grills with aluminium volume control dampers,as per specifications.
494	Supplying, & fixing, of powder coated extruded aluminium section return air grills with louvers butwithoutvolume control dampers,complete as per required.
495	Supplying, fixing, testing commissioning of supply airdiffusers of powder coated aluminium with aluminium volume control dampers. ( 23Nos of 600x600mm)
496	Supplying, fixing, testing, commissioning of return air diffusers of powder coated aluminium.
497	Supplying, fixing Acoustic lining of supply air ducting complete with G.I frame, tissue paper, 28G perforated al. Sheet, 25mm thick 32kg/cu.m fibreglass insulation as per CPWD specifications.
498	Supplying, fixing , testing and commissioning of fire dampers in supply air duct/ main branch and return air path as & where required of required sizes including control wiring. The damper shall be motorised and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored .the spring return action shall be built mechanism and not externally mounted . The damper shall also be closed in the event of a fire signals complete as required as per specifications .
499	Fire Damper
500	Motorised Actuator
501	HVAC - VRV
502	Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R410A Refrigerant, vibration isolators, with suitable foundation etc. complete as required.The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping.The unit shall be suitable to work on 400V+/-10%, 3 Phase, 50Hz AC power supply.The unit shall be filled with first charge of the refrigerant and ready for use as required.The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .
503	INDOOR UNIT
504	Supply, installation, testing and commissioning of following minimum capacity 4-wayflow VRV/ VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/ dynamically balanced blower, multi speed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc., suitable for operation on single phase 230V±10%, 50 HzAC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inl et conditions of 27 Degree CD Band 19 Degree CWB temperature.
505	4-Way Cassette type
506	1.0 TR
507	2.0 TR
508	2.4 TR
509	3.2 TR
510	Supply, installation, testing and commissioning of following minimum capacity VRV/ VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/ dynamically balanced blower, multi speed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cordless remote control, drain pan, necessary accessories etc., suitable for operation on 230V±10%, 50Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.
511	1.65 TR
512	REFRIGERANT PIPING
513	Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/harddrawn copper refrigerant piping for VRV/VRFsystem, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :
514	34.9 mm O.D (wall Thickness-1.2 mm) (Insulation: 19 mm)
515	28.6 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm)
516	22.2 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm)
517	19.1 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm)
518	15.9 mm O.D (wall Thickness-1.0 mm) (insulation : 13 mm)
519	12.7 mm O.D(insulation : 13 mm )
520	9.5 mm O.D(insulation : 13 mm)
521	6.4 mm O.D (insulation : 13 mm )
522	CONDENSATE DRAIN UPVCPIPE
523	Supply, installation, testing and commissioning ofuPVC Pipe ,complete withfittings, supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and accessoriesas perspecifications, drawings.
524	25 mm dia
525	32 mm dia
526	40 mm dia
527	50 mm dia
528	Imported fittings Y-jointsand headers etc.
529	Control & Trasmission Wiring
530	Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper in suitable conduits between indoor and outdoor unit.
531	Timer for Split ac for Server

Also Visit

Tenders

Delhi Tenders

Services Tenders

Space Planning and Designing Tenders

Interior Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Request For Qualification Cum Proposal For Interiors And Fit-Out Works Of New Office Space For Nicdc At Ht House, Kg Marg, New Delhi On Percentage Rate Basis, Delhi-Delhi

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Request For Qualification Cum Proposal For Interiors And Fit-Out Works Of New Office Space For Nicdc At Ht House, Kg Marg, New Delhi On Percentage Rate Basis, Delhi-Delhi

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us