Capital Outlay On Urban Development Providing And Fixing Furniture In Amenities Buildings And Other Misc Work At New Mla Quarters At Sector-17, Gandhinagar.-1 Providing and fixing False ceiling of light weight Calcium Silicate tiles Tegular Edge of size 595 x 595 15mm densified edge, having 100% humidity resistance and incombustible as per BS 476 part - 4 with thermal conductivity of 0.043 W/m0 kC, with NRC of 50 and approved surface design to be placed in the Grid suspended Ceiling with border of Gypsum sheet, Grid system made of Galvanised steel Section with main T runner 3.6 mt long with size 38 x 24 x 0.30 mm spaced at 1200mm c/c and cross T of 1.2 mt long with size 24 x 24 x 0.30 mm spaced between main T at 600mm c/c to from a grod of 600 x 1200mm and secondary cross T of length 600 mm to be inter locked at middle of the 600 x 1200 mm panel to from a grid of 600 x 600 mm. The wall angle of size 24 x 24 0.55mm to be fixed all around the perimeter of the wall. The main T runner to be suspended from the ciling using GI sloted cleats and 50 mm long dash fasteners and having Silhouttes, 4mm GI adjustable rods with galvanised level clips with all labour and material and props required for any height and as directed by Engineer incharage. 2 Pro. And fixing single layer water proof gypsum board 12.5 mm thick sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x 0.8 mm at 1220 mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat, anchor fastener, scoch bolt connecting cleat,joining compound top coat on ceiling incl.making necy.opening for light fitting,diffuser etc. comp. as per detail drawing as directed 3 Providing Dining table with Veneer + Full Core Laminate + Granite Top as per drawing. Having base materials of Kiln dried & treated fine quality C.P. Teakwood Legs & 19mm thick Plywood structure, with Top part of Table covered with 4 mm thick Veneer,18-25mm thick Granite with Polished Edges &Full-core Laminate as/drawings. Rest visible faces to be covered with 4 mm thick Veneer as/drawing & Selection including All necessary fixtures &fasteners including anti slip leg pads. All exposed edges shall be covered with 8mm thick Teak wood beading Patti.All exposed wooden & veneer faces to be finished with matt finish melamine polish.All remaining non-visible faces & edges shall be painted with Enamel (oil) Paint of matching shade of other finished surfaces.Complete as per drawings & instruction of Architect & Engineer-in-Charge. 4 Providing Dining Chair having base materials of Kiln dried & treated fine quality C.P. Teakwood Legs, with 45Kg/M2 Density HR foam with required Thickness as per design in Seat & Backrest portion, covered with upholstered fabric of suggested shade & finish as per selection by architect. including All necessary fixtures &fasteners (M14) including anti slip leg pads. All exposed edges shall be covered with 8mm thick Teak wood beading Patti, All exposed wooden & veneer faces to be finished with matt finish melamine polish. All remaining non-visible faces & edges shall be painted with Enamel (oil) Paint of matching shade of other finished surfaces. Complete as per drawings & instruction of Architect & Engineer-in-Charge. 5 Providing and fixing acoustical wall panelling using Anutone or equivalent make for whole height using design panel of 9 mm thick non grid type, fabric finished core Polyfibre-based, High density SynthPF large-format, synth slim rigid acoustic wall panelling. The wall panelling shall be fixed with sound strut CC10 or equivqlent screws fixed horizontal / vertical to wall at every 600 mm c/c. Slim 9mm having density of 220 kg/m3 having A class fire rating with NRC (A-mounting) up to 0.4 shall be fixed on Strand Primer of 10mm shall be installed with synth PF 10x10 on Struct CC10.Synth PF 10x10mm thick adhered on strand panel by using Stick 7 adhesive. Non Grid type polyfibre synth PF 10x10 shall have density 500 kg/m3 having NRC rating 0.7 shall be fixed using Stick 7 adhesive. The colour shade as approved by Architect and as directed by Engineer-in-charge with all labour and materials. 6 Carpet Flooring Supply and fixing of Loope Pile Carpet of Pile Fiber: 100% Bcf Polypropliene Yarn Construction & Type: Solution Dyed Bulk Continuous Filament Machin Gauge & Stich Rate: 2.54mm (1/10”) 39.4 Rows/100mm, 48/10 Cms. Construction: Loop Pile High Low Scroll Graphic. Density Factor: 189,600 Tufts/Sq.Mts Tufted Pile Weight & Hight: 650 Gm/Sq.Mt, 6mm (5 %+/-) Backing: Primary: Woven Polyproplene, Secondery: Action Back Moth Proffing: Naturally Resistat Bond Strength: 30 Newton Tuff Withdrawal Strength: 20 Newton Flammability: (Astm D 2859-96 & Cpsc-Ff-170) 8 Passes Static Generation: Under 3 Kv Light Fastness: 5+ Usage Area : Commercial Heavy Duty Like Auditiriom Office 7 Heavy Traffic Area with backing of 8mm thick armour fixing on the floor with using favicol SR 505 solution and fixing the carpet above armour including all accessories, material & labor complete including dismentling of old carpet, as directed by Architect / Engineer – in – charge. 7 Providing and fixing Minimum 18mm thick inter locking rubber gym floor tile having EPDM parttern on it as per selection and direction of engineer in charge. 8 Finishing wall with textures in accordance with the Architects instructions. The finished spray based or roller based texture shall be uniform, free of blemishes, and meet the specified aesthetic requirements. Crack filling and Surface preperation shall be carried out prior to texture application to ensure proper adhesion and a smooth finish.Paint on Texture will be applied separately. The work shall be done as per the approved shop drawings (to be prepared by contractor), specifications, sample approved and as directed by the Architect and Engineer-in-charge.The rate shall be for complete items inclusive of all material, labour, wastages, necessary tools & tackles, loading, unloading, placing at all floors and for all leads, all accessories as described in item description approved for all floors, and all places within campus. Contractor shall do all the needful and shall fulfil the Architects design intent. No additional claims will be entertained for this. 9 Providing supplying and fixing of approved quality / make executive push back chair / theatre chair with handle and self tip up mechanism seat and back frames shall be made out of ERW tube fabric shall be of approved quality make and shade. Arm rest in graded plastic, seating arrangement numbering shall be clearly visible and of approved make. All structural connections, tapestry cushion etc. including proper anchoring of chairs to the surface complete. it shall be as per Architects details and shall be as instructed by the Engineer - in - charge 10 Providing and fixing roller blind with superior quality of imported fabrics as per approved shade and matching incl Acmeda Mechanism including all necessary fitting like bracket chain etc. Complate as per instruction of engineer In-charge. 11 Providing High back revolving & tilting executive chair, as per approved sample by chief architect/project in charge, with PU.handle, hot pressed bend ply in seat and back, ergonomically design with natural shape of spine supporting entire back of the user and provide good lumber support.The back rest ht is 26 Upholstered with 40 density PU foam in seat and back, covered with approved tapastry of matty quality. Bottom: 38mm dia x 1.6 mm thick pipe used in five prone stand with castors, Single position lock, gas lift operating system and tilt mechanism made from M.S. sheet [2.5, 3.15, 4mm thickness], duly powder coated 40 to 50 micron. 12 Providing Medium back revolving & tilting chair, as per approved sample by chief architect/project in charge, , hot pressed bend ply in seat and back, ergonomically designed. Upholstered with 40 density PU foam in seat and back. covered with approved tapasty of matty quality. Back Height is 16 from the seat. Soft PU handle as per sample Bottom: 38mm dia x1.6mm thick pipe used in five prone stand with castors, Single position lock, gas lift operating system and tilt mechanism made from M.S. sheet[2.5,3.15,4mm thickness], duly powder coated 40 to 50 micron. 13 Providing Low back revolving & tilting chair, as per approved sample by chief architect/project in charge, , hot pressed bend ply in seat and back, ergonomically designed. Upholstered with 40 density PU foam in seat and back. covered with approved tapasty of matty quality. Back Height is 16 from the seat. Soft PU handle as per sample Bottom: 38mm dia x1.6mm thick pipe used in five prone stand with castors, Single position lock, gas lift operating system and tilt mechanism made from M.S. sheet[2.5,3.15,4mm thickness], duly powder coated 40 to 50 micron. 14 Visitor’s group seating of Three, Top shell (Seat & Back support) made from S.S. perforated sheet, S.S. pipe & Base made from S.S. tubes as per sample approved by Engineer in charge complete finish with PU powder coating. The whole work is to be completed as per approved make list & selection by officer of user department & Engineer in charge.. 15 Three Seater SofaProviding and supplying the three Seater sofa will be total prepared in 18mm. thick ply wood structure it is seat, back and handle of sofa shall be made from plywood and handle shall be finished with selected veneer and finished with melamine polish as per direction and on top 4.0 rubber cushion and top 25mm thick and 32 density U-Foam finished with leather rexin as per selected sample. At back support also 0.53mm width x 0.74 mm for 2 seated back, fitted with 2.0 rubber cushion with 25mm U-Foam with 32 density appropriate 3 angle support, also done finishing along with leather finished. Horizontal and vertical support also as shown in drawing to create decoration and strengthening support. Including all materials and labour etc. complete as per detail drawing and instruction of engineer-in charge. 16 Providing and fixing post formed Work Top with mounted and made from 36mm (fully) MDF board with overall size 1200/1500/1800 X 750 mm as per requirements with necessary openings, etc. All materials like Plywood, Wooden biddings, Laminates, Hardwares and accessories, PVC edgeband and paints should have to be from approved makelist and with approval from consulting Architect & Engineer-in-charge. 17 Providing and fixing Gable end to support top having overall size 600 X 710 X 25mmAll materials like Plywood, Wooden biddings, Laminates, Hardwares and accessories, PVC edgeband and paints should have to be from approved makelist and with approval from consulting Architect & Engineer-in-charge. 18 Providing and fixing modesty panel connecting Gable end and partition made from 18mm BSL boards. All materials like Plywood, Wooden biddings, Laminates, Hardwares and accessories, PVC edgeband and paints should have to be from approved makelist and with approval from consulting Architect & Engineer-in-charge. 19 Providing and fixing Side rack having size 1200 X 710 X 450 mm or 900 X 710 X 450 mm or 600 X 710 X 450 mm, sliding shutters and Back storage units with 710mm height including top.All materials like Plywood, Wooden biddings, Laminates, Hardwares and accessories, PVC edgeband and paints should have to be from approved makelist and with approval from consulting Architect & Engineer-in-charge. 20 Providing storage rack ready to assemble type, self standing, over hanging or partition mounted storage system having 450 mm depth and made from 18mm both side pre-laminated particle board., as specified in specification sheet.All materials like Plywood, Wooden biddings, Laminates, Hardwares and accessories, PVC edgeband and paints should have to be from approved makelist and with approval from consulting Architect & Engineer-in-charge. 21 Providing and fixing Drawer Unit 600X400X500mm with one drawer and one locker with locking system All materials like Plywood, Wooden biddings, Laminates, Hardwares and accessories, PVC edgeband and paints should have to be from approved makelist and with approval from consulting Architect & Engineer-in-charge. 22 Providing and Fixing alluiminium Openanle Door and Partition with partially 4 mm thick plain Glass & parthially 12 mm novapan with Anodized hollow Section Frame of Approved shade of Size ( 63.50 x 38.10 x 1.2 mm ) @ 0.643 kg / rmt and Door Shutter Size as same ( 63.50 x 38.10 x 1.2 mm ) @ 0.643 kg / rmt including providing Rubber gasket and Beading clips @ Wt 0.124 kg/ rmt including Providing Heavy Handle , Locking arrangement , Brascket , stopper etc accessoties Fitting with Silicon and all required Support , material Labour and Equipment as per Directed by Engineer in charge.
