Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 09-06-2025 | Corrigendum | Financial Bid | 11-06-2025 |
| 2 | 04-06-2025 | Extension of Bid Submission Date | Date | 11-06-2025 |
| 3 | 20-05-2025 | Bid Submission Date Extension | Date | 04-06-2025 |
| 4 | 12-05-2025 | Specification | Other | 19-05-2025 |
| Sl. No. | Item Description |
| 1 | Sludge drying bed civil works |
| 2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) |
| 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 7 | Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 8 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 9 | Solid block masonry using pre cast solid blocks (factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete |
| 10 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand) |
| 11 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate |
| 12 | Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000x450x50 mm, reinforce with 8 mm dia four nos. longitudinal & 9 nos cross sectional T.M.T hoop bars, including providing 50 mm dia perforation @ 100 to 125 mm c/c, including providing edge binding with M.S flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge. |
| 13 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within as lead of 50 m. All kinds of soil. |
| 14 | Providing and fixing PVC pipes including jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2 |
| 15 | Providing and fixing PVC pipes including jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 110 mm dia 6 Kgf/cm2 |
| 16 | Supplying, filling, spreading & leveling gravels of size range 40 mm to 30 mm, in the recharge pit, overthe layer of floor finish, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 17 | Supplying, filling, spreading & levelling gravels of size range 30 mm to 20 mm, in the recharge pit, overthe layer of floor finish, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. Filter media second layer |
| 18 | Supplying, filling, spreading & leveling gravels of size range 20 mm to 6 mm, in the recharge pit, overthe layer of floor finish, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. Filter media third layer |
| 19 | Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm, in the recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 20 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer |
| 21 | Finishing walls with Acrylic Smooth exterior paint of required shade : New York (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 22 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 23 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality; 32 mm diaMetre pipe |
| 24 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality; 40 mm diaMetre pipe |
| 25 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality; 50 mm diaMetre pipe |
| 26 | Providing, fixing Poly carbonate corrugated sheet 0.8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 m or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/vertical/curved surface, but excluding the cost of purlins, rafters, trusses and including cutting to size shapes where ever required. |
| 27 | Pump house & Screw Press shed civil works |
| 28 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared |
| 29 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within as lead of 50 m. All kinds of soil. |
| 30 | Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (Measurements to be taken off the face area timbered). Depth not exceeding 1.5m |
| 31 | DRY RUBBLE MASONARY. Dry rubble without concrete levelling course masonary with good quality blasted rubble including packing to compactness to lines and levels cost and conveyence of all materials labour charges etc. complete as per direction of Departmental officers at site. |
| 32 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 33 | Filling with contracter\"s own earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m as per direction of site Engineer-in-charge |
| 34 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) |
| 35 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforement, including admixtures in recommended proportions as per IS : 9103 to accerleate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge.Note :- Cement content considered in this item is @ 330 kg/cum. Excess or less cement used as per design is payable or recoverable separaterly. All work upto plinth level |
| 36 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforement, including admixtures in recommended proportions as per IS : 9103 to accerleate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge.Note :- Cement content considered in this item is @ 330 kg/cum. Excess or less cement used as per design is payable or recoverable separaterly. All work above plinth level upto floor V level. |
| 37 | Extra for providing richer mixes at all floor levels. Note :- Excess/less cement over specified cement content used is payable/ recoverable separaterly. Providing M-30 grade concrete instead of M-25 grade BMC/RMC ( Note :- Cement content considered in M-30 is @ 340 kg/cum) |
| 38 | Centering and shuttering including strutting, etc. and removal of form for: Foundations, footings, base of columns, etc for mass concrete |
| 39 | Centering and shuttering including strutting, etc. and removal of form for: columns, Pillars, Piers, Abutments, Posts and Struts |
| 40 | Centering and shuttering including strutting, etc. and removal of form for: Lintels, beams, plinth beams, girders bressumers and cantilevers. |
| 41 | Centering and shuttering including strutting, etc. and removal of form for: Suspended floors, roofs, landings, balconies and access paltform |
| 42 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars of grade Fe-500D or more |
| 43 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 44 | providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 micron epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55 mm) with EPDM seal, complete upto any pitch in horizontal/vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 45 | Providing and fixing precoated galvanized steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:277, in 240 Mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microms using self drilling/self tapping screws complete: Ridges plain (500-600 mm) |
| 46 | Solid block masonry using pre cast solid blocks (factory made) of size 40x40x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete |
| 47 | 12 mm cement plaster finished with a floating coat of neat cement of mix: 1:4 ( 1 cement: 4 fine sand) |
| 48 | Extra for providing and mixing water proofing material in cement palster work in proportion recommended by the manufacturers. |
| 49 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufacture from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover. |
| 50 | Providing and fixing ball bearing for rolling shutters. |
| 51 | Providing and fixing glazing in aluminium door, window, ventilator sutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-Charge. (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4.0 mm thickness |
| 52 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer |
| 53 | Finishing walls with Acrylic Smooth exterior paint of required shade : New York (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 54 | Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanized iron/steel works |
| 55 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two of more coats of New York |
| 56 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate |
| 57 | Soakpit civil |
| 58 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared |
| 59 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (exceeding 30 cm in depth, 1.5 m in width or 10 sqm on plan), including disposal of excavated earth, lead upto 50m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed. All kinds of soil. |
| 60 | Extra for every additional lift 1.5 m or part there of in excavation/banking excavated of stacked materials. All kinds of soil |
| 61 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 62 | Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete |
| 63 | Supplying, filling, spreading & levelling stone boulders of size range 5 com to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge |
| 64 | Supplyin, fitting, spreading & levelling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge |
| 65 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) |
| 66 | Solid block masonry using pre cast solid blocks (factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15 cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete |
| 67 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 fine sand) finished rough with sponge |
| 68 | White washing with lime to give an even shade : New York (three or more coats) |
| 69 | Providing and fixing PVC pipes including jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2 |
| 70 | Supplying, Installing, testing and commissioning of C.I. butterfly valves conforming to BS 5155 (PN 1.6) slim seal standard lever operated type with required flanges, nuts, bolts etc. complete. 150 mm nominal dia |
| 71 | MS Puddle Flanges for 150 mm pipe - Manufacturing supplying and fitting 150 mm dia MS Flange having shell thickness 10 mm depth 150 mm with suitalbe bolt, holes, fixing the flange in position with required welding around the flange, pipe joint grinding for smoothing the welde portion, including painting with red oxide primer etc. complete as directed by departments officers. |
| 72 | Drilling suitable holes in reinforced or plain cement concrete wall with power driven drill machine to a minimum depth of 200 mm upto 300mm for Puddle flange fixing. |
| 73 | Pump house & Screw Press shed Electrical |
| 74 | Wiring for light point/fan point/exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conducter single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulsated copper conducter single core cable etc as required. Group C |
| 75 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modulat switch, connection etc. as required. (For light plugs to be used in non residential buildings). |
| 76 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modulat switch, connection etc. as required. (For light plugs to be used in non residential buildings). |
| 77 | Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conducter, single core cable in surgace/recessed medium class PVC conduit as required 2x2.5 sq. mm + 1x2.5 sq. mm earth wire |
| 78 | Installation, testing and commissioning of pre-wired, fluorescent fitting/compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conducter, single core cable and earthing etc. as required. |
| 79 | Installation of exhaust fan in the existing opening, including making good the damage connection testing, commisioning etc. as required. Upto 450 mm sweep |
| 80 | Extra for Fixing the louvers/shutters complete with frame for a exhaust fan of all sizes |
| 81 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"c\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 82 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 bolts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps |
| 83 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator 8 way, Double door |
| 84 | Starter Panel: Supply, Erection, testing and commissioning of Starter Panel including civil and mounting arrangements with painitng etc as required. Sheet: 14/16 SWG thick CR sheet Paint: Siemens grey with powder coating RYB phase indication lamps ideal make - 1 set, Starter indication lamp arrangement - 4 sets digital Multi function Metre - 1 nos Current transformer 25/5A 15VA class 1 - 1 SetBushbar Support : SMC Bushbar Size: 80 A, TPN, 3 phase, 4 wire AL. BUS.Incomer 100A 25KA 4P MCCB - 1 nos Outgoings 63 A TPN MCCB - 3 nos with Automatic star delts starter arrangements with auto manula provision63A TPN MCCB - 1 nos,20 A TPN MCCB - 2 nos with automatic DOL starter arrangements with auto manual provision, 20A TPN MCCB - 1 nos, |
| 85 | Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). 3.5 core 25 sq.mm |
| 86 | Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering ( in ordinary soil). 4 core 10 sq mm |
| 87 | Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering ( in ordinary soil). 4 core 6 sq mm |
| 88 | Supplying of PVC insulated, heavy duty, aluminium/copper conducter. 1.1 KV grade armoured. MV cable of the following sizes as required, genrally conforming to IS:1554/Part-I/1970. (Note : Before procurement to check the cable measurement as per site condition) 3Cx2.5 Sqmm Ar. Cu |
| 89 | Supplying of PVC insulated, heavy duty, aluminium/copper conducter. 1.1 KV grade armoured. MV cable of the following sizes as required, genrally conforming to IS:1554/Part-I/1970. 2Cx1.5 Sqmm Ar. Cu |
| 90 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in gound including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm |
| 91 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in the existing masonary open duct as required. Upto 35 sq. mm |
| 92 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1 mm thick saddle) |
| 93 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1 mm thick saddle) |
| 94 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required. 3 1/2x25 sq.mm (28mm) |
| 95 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required. 4Cx10 sq.mm (25mm) |
| 96 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required. 4Cx6 sq.mm |
| 97 | Supplying and making end termination with brass compression gland and Copper lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required. 3Cx2.5 sq.mm Ar. Cu. |
| 98 | Supplying and making end termination with brass compression gland and Copper lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required. 2Cx1.5 sq.mm |
| 99 | Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, jointed with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width x 50 mm depth x 1.6 mm thickness |
| 100 | Earthing with copper earth plate 600 mm x 600mm x 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coal and salt as required. |
| 101 | Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. |
| 102 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required. |
| 103 | Supplying and making cable route marker with cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at top with a thicknessof 10 cm including inscription duly engraved as required. |
| 104 | Supply and laying of 11 KV Grade, Elastemer Polymer 2.5 mm thickness |
| 105 | Supply and fixing carbondioxide fire extinguisher type 4.5 kg capacity. |
| 106 | Supply and transportation of 20 W +/- 10%, 2000 lumens, 1200 mm length LED retro tube light, housing made with aluminium anodised body, wide operating voltage with double side connection, PF0.9, Surge protection:> 2 KV, THD< 15%, with inbuilt driver and frosted cover CCT: 3000K-6500K as desired by the department and as per IS specifications, minimum CR180, etc complete with 5 years warranty with BIS certification. Lumainaire make : Phillips/Wipro/Crompton/Bajaj/Havells |
| 107 | Supply and transportation of 10W LED Bulk head fitting with milky diffuser heat sink integrated with housing with all accessories etc complete with 5 years warranty Lumainaire Make : Phillips/OSRAM/GE/Crompton/Bajaj |
| 108 | Supply of 16\" (400mm) BLDC 30 W Wall mounted fan with service value 2.7 CMM/Watt with all accessories etc. Make : Atomberg/Crompton/Orient/Havells/Halonix. |
| 109 | Supply of 12\" (300mm), 900 RPM Heavy duty exhaust fan with metallic blades. Make : Crompton/Almonard/Havells Turbo Force SP. |
| 110 | Supplying and fixing of following Sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm |
| 111 | Sludge Drying Bed Electrical |
| 112 | Supplying and fixing of following Sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm |
| 113 | Supplying and drawing following sizes of FRLS PVC insulated copper conducter, single core cable in the existing surface/recessed steel/PVC conduit as required 3x 1.5 sq.mm |
| 114 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator) 8 way, Double door. |
| 115 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"c\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 116 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 bolts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A |
| 117 | Supplying and laying of one number additional PVC insulated and PVC sheathed armoured aluminium power calbe of 1.1 KV grade of the following sizes in ground in the same trench in one tier horizontal formation including widening the trench by 20 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil) 3 core 6 sqmm |
| 118 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sqmm |
| 119 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size in the existing masonary open duct as required. Upto 35 sqmm |
| 120 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sqmm (clamped with 1 mm thick saddle) |
| 121 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required 3x10 sqmm (22mm) |
| 122 | Supply conveyance, installation, testing and commissioning of 40 W LED Flood light output greater than 105 lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than o.95 at full load, internal surge protection upto 8 KV and aluminium pressure die cast powder coated housing, acrylic cover complete with THD less than 10% power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer) |
| 123 | Supply of 18 heavy duty Exhaust fan |
| 124 | Installation of exhaust fan in the existing opening, including making good the damage connection testing, commisioning etc. as required. Upto 450 mm sweep |
| 125 | Screw Press Equipment |
| 126 | Design, Engineering, Supply and Installation of SP 120 in SS304 with all accessories mentioned in the technical data sheet. Sludge De-Watering - Screw press with MOC - SS 304, capacity of 6 m³/hr.Screw Press Feed Pump of 6 m³/hr @ 12 m, with CI body and SS 304 impeller – Semi-open impeller pumps – Centrifugal with mechanical seal & IE3 motor. Two pumps, each coupled with a 1.5 kW, 2-pole induction motor, along with base frame assembly and required suction and delivery valves, NRV, pressure gauges, and piping. Wash water pump with a capacity of 0.12 m³/hr @ 30 m, with CI body and CI impeller – Coupled pumps – Centrifugal with mechanical seal & IE3 motor. Two pumps, each coupled with a 0.5 kW, 2-pole induction motor, along with base frame assembly, required suction and delivery valves, NRV, pressure gauges, and piping.Mechanically operated diaphragm-type dosing pump with CI body and SS 316 wetted parts, with suction strainer, NRV, and other required accessories, delivering 480 LPH @ 3 bar with required suction and delivery valves, NRV, pressure gauges, and piping.Dosing tank of 2000 liters in LDPE, with a three-blade agitator operating at 60-80 rpm for dosing, along with a dosing tank of capacity 2000 liters in SS 316, with a minimum 1.5 kW electrical control panel. Cables up to 50 Metres limit as mentioned in the technical data sheet. (Civil items like covered roof with equipment platforms will be paid separately and executed under civil works.) |
| 127 | Pumps and Fittings for treated water disposal |
| 128 | Supply, Erection, Testing, and Commissioning of Horizontal Centrifugal Pump set with a capacity of 120 m³/hr against a total head of 20 m, with a CI body and CI impeller. Coupled pumps – Centrifugal with mechanical seal & IE3 motor. The pump is coupled with a 9.3 kW, 2-pole induction motor, along with a base frame assembly, coupling, and coupling guard. All accessories are supplied at the site, fitted on a common base plate in correct alignment. (Make: KSB or Equivalent). |
| 129 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 250 mm dia (wall thickness 6.3 mm). |
| 130 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 80 mm dia |
| 131 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 250 mm dia. |
| 132 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 65 mm dia |
| 133 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 150 mm dia |
| 134 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 200 mm dia (wall thickness 6.3 mm). |
| 135 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 150 mm dia. |
| 136 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS : 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required : 150 mm dia. |
| 137 | Supply, Erection, Testing, and Commissioning of 1 no. pressure gauge 4 dial with screwed valve tee and fittings |
| 138 | Pumps and Fittings for park irrigation line |
| 139 | Supply, Erection, Testing, and Commissioning of Horizontal Centrifugal Pump set with a capacity of 25 m³/hr against a total head of 30 m, with a CI body and CI impeller. Coupled pumps – Centrifugal with mechanical seal & IE3 motor. The pump is coupled with a 3.7 kW, 2-pole induction motor, along with a base frame assembly, coupling, and coupling guard. All accessories are supplied at the site, fitted on a common base plate in correct alignment. (Make: KSB or Equivalent). |
| 140 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 50 mm dia |
| 141 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 100 mm dia |
| 142 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 100 mm dia. |
| 143 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 32 mm dia |
| 144 | Providing, laying, testing, and commissioning of \"C\" class heavy-duty MS pipe conforming to IS 3589/IS 1239, including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets, etc., and fixing the pipe on the wall/ceiling with a suitable clamp/support frame. The work includes painting with two or more coats of synthetic enamel paint of the required shade, complete as required. Pipe size: 80 mm dia |
| 145 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 80 mm dia. |
| 146 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS : 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required : 80 mm dia. |
| 147 | Supply, Erection, Testing, and Commissioning of 1 no. pressure gauge 4 dial with screwed valve tee and fittings |
| 148 | Toilet at Security Gate |
| 149 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within as lead of 50 m. All kinds of soil. |
| 150 | Centering and shuttering including strutting, etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 151 | Centering and shuttering including strutting, etc. and removal of form for : Lintels, beams, plinth beams, girders bressumers and cantilevers |
| 152 | Centering and shuttering including strutting, etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform |
| 153 | Provide and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 154 | Random rubble masonay with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 155 | Random rubble masonay with hard stone in supersturcture above plinth level and floor five level, including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 156 | Providing and laying in position specified grade of reinforced cement concrete excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 157 | Reinforced cement concrete work in beams, suspended floors, roofs (having a slope up to 15°), landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases, and spiral staircases up to the fifth-floor level, excluding the cost of centering, shuttering, finishing, and reinforcement. The concrete mix shall be 1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate of 20 mm nominal size). |
| 158 | Reinforced cement concrete work in arches, arch ribs, domes, vaults, shells, folded plates, and roofs having a slope more than 15° up to floor five level, excluding the cost of centering, shuttering, finishing, and reinforcement, with a mix ratio of 1:1.5:3 (1 cement: 1.5 coarse sand (Zone III): 3 graded stone aggregate of 20 mm nominal size). |
| 159 | Steel reinforcement for R.C.C. work includes straightening, cutting, bending, placing in position, and binding all complete up to the plinth level using Thermo-Mechanically Treated (TMT) bars of grade Fe-500D or more. |
| 160 | Steel reinforcement for R.C.C. work above the plinth level follows similar specifications, ensuring structural integrity and compliance with required standards. It includes all necessary processes such as straightening, cutting, bending, placing in position, and binding using TMT bars of grade Fe-500D or more. |
| 161 | Solid masonry using precast solid blocks (factory-made) of size 30x20x15 cm or the nearest available size, conforming to IS 2185 Part I of 1979, for the superstructure up to floor two level with a thickness of 15 cm. The mortar mix used is CM 1:6 (1 cement: 6 coarse sand) etc complete |
| 162 | Solid block masonry using precast solid blocks (factory-made) of size 30x20x20 cm or the nearest available size, conforming to IS 2185 Part I of 1979, for foundation and plinth work with a thickness of 20 cm and above. The mortar mix used is CM 1:6 (1 cement: 6 coarse sand) etc. complete |
| 163 | Filling available excavated earth (excluding rock) in trenches, plinths, and sides of the foundation in layers not exceeding 20 cm in depth. The deposited layer is consolidated by ramming and watering, with a lead of up to 50 m and a lift of up to 1.5 m. |
| 164 | 18 mm thick cement plaster in two coats: 12 mm thick (1:5 cement-coarse sand) under layer, finished with 6 mm thick (1:6 cement-fine sand) top layer. |
| 165 | 12 mm cement plaster finished with a floating coat of neat cement of mix: 1:3 ( 1 cement: 3 fine sand) |
| 166 | 12 mm cement plaster finished with a floating coat of neat cement of mix: 1:4 ( 1 cement: 4 fine sand) |
| 167 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size). |
| 168 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS: 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete. |
| 169 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 170 | Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement: 4 coarse sand) mixed with 2% integral waterproofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) and finished neat complete. |
| 171 | Applying one coat of water-thinnable cement primer of approved brand and manufacturer on wall surface: Water-thinnable cement primer. |
| 172 | Finishing walls with Acrylic Smooth exterior paint of required shade : New York (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 173 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/litre, of approved brand and manufacturer including applying additional coats wherever required, to achieve even shade and colour. Two coats. |
| 174 | Providing and fixing factory-made P.V.C. door frame of size 50×47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15×15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19×19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided throughout the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge. |
| 175 | Providing and fixing factory-made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and sized of 19 mm × 19 mm for styles and 15×15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45-degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be tapered in 45-degree on inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom, and lock rails shall be provided on both sides of the panel. 10 mm (5 mm × 2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. Paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles & rails with 7 mm (5 mm + 2 mm) thick × 15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc., complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. 30 mm thick plain PVC door shutters |
| 176 | Providing and fixing factory-made ISI-marked steel glazed doors, windows, and ventilators, side/top/center hung, with beading and all members such as F7D, F4B, K11B, and K12B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design (sectional weight of only steel section shall be measured for payment). Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) |
| 177 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked black solid plastic seat and lid. |
| 178 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 179 | Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. |
| 180 | Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete. Semi rigid pipe 32 mm dia |
| 181 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms |
| 182 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Rectangular shape 453x357 mm |
| 183 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 184 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931, 15 mm nominal bore. |
| 185 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms, 15 mm nominal bore. |
| 186 | Providing and fixing PVC pipes including jointing of pipes with one-step PVC solvent cement, trenching, refilling & testing of joints as per direction of Engineer in Charge. 20 mm dia, 12 Kg/cm². |
| 187 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one-step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall, etc. 20 mm pipe, 10 Kg/cm². |
| 188 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one-step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall, etc. 15 mm pipe, 10 Kg/cm². Exposed on wall |
| 189 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one-step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall, etc. 75 mm pipe, 6 Kg/cm². |
| 190 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one-step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall, etc. 110 mm pipe, 6 Kg/cm². |
| 191 | Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06 mm aggregate for the preparation of bed shall be paid separately) 15 to below 25 flush capacity. |
| 192 | Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i.e. fittings &fixtures for tank shall be paid separately. |
| 193 | Providing and fixing PVC multi floor trap 110 mm dia., 75 mm dia outlet of approved make including connection of waste pipe line from wash basin with tail piece or boss tee, stainless steel grating on top of the trap of approved make etc. complete all as specified and directed. |
| 194 | Toilet Electrical |
| 195 | Wiring for light point/fan point/exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conducter single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conducter single core cable etc as required. Group A |
| 196 | Supplying and fixing following size/modules, GI box alongwith modular base & cove plate for modular switches in recess etc. as required . 3 module (100mmX75mm) |
| 197 | Installation, testing and commissioning of pre-wired, fluorescent fitting/compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 198 | Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conducter, single core cable in surgace/recessed medium class PVC conduit as required 2x1.5 sq. mm + 1x1.5 sq. mm earth wire |
| 199 | Supplying and fixing following piano type switch/socket on the existing switch box/cover including connections etc. as required. 5/6 amps switch |
| 200 | Installation of exhaust fan in the existing opening, including making good the damage connection testing, commisioning etc. as required. Upto 450 mm sweep |
| 201 | Drain Rerouting |
| 202 | Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mix plant at Omc, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm) having CBR Value-25 |
| 203 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
