|
| 1 | BED HARD/BED PLY TOP : ( Drg No.FD-213,217, 246/ 247) |
| 2 | M&L for removal of u/s ply wood of bed in any position, S&F new ply wood 12 mm thick, BWR grade, ISI marked including fixing in same position all as shown on drg with suitable size screws & cup washers, all specified and directed by the Engineer-in-Charge |
| 3 | M&L for removing u/s headrestand S&F New headrest complete of 1st class hard wood teak frame (Well-seasoned) duly covered with 4mm thick teak veneer ply complete all as specified & shown in drg. |
| 4 | M&L for removing u/s footrestand S&F New footrest complete of 1st class hard wood teak frame (Well-seasoned) duly covered with 4mm thick teak veneer ply complete all as specified & shown in drg. |
| 5 | M&L for removing of u/s long rail and S&F of new new long rail made out of fully seasoned Ist class hard wood all as specified & shown in drg. |
| 6 | M&L for removing of u/s support/Stiifner and S&F of new support made out of 2nd class hard wood (Well-seasoned) and all as specified & shown in drg. |
| 7 | M&L for removal of u/s veneer ply of Headrest of bed complete in any position, S&F new 4 mm thick one side teak veneered ply on both sides, all round teak beading all as shown on drg, as specified and directed by Engr-in-charge |
| 8 | M&L for removal of u/s veneer ply of Footrest of bed complete in any position, S&F new 4 mm thick one side teak veneered ply on both sides, all round teak beading all as shown on drg, as specified and directed by Engr-in-charge |
| 9 | S& F new bracket of size 100 x 100 x 30 mm made of hard wood and fixing with 02 Nos suitable size steel screws complete as all as specified and directed. |
| 10 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of French polishof smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 11 | Chair dining : (Drg No. FD-16,203, 228, 262, 270,279 ): Removing of old unserviceable the following parts from chair dining, and supply and fixingnew same parts of hard wood duly finished with existing shape and fixed with bamboo pin and fevicol including tightening of other joints and applying 2 coats of French polish after preparation of existing surfaces complete all as shown on drg and as directed by Engineering-in-charge |
| 12 | Front legs (L&R) |
| 13 | Rearlegs (L&R) |
| 14 | Side rail with holes (L&R) side for canning |
| 15 | Front and back Rails with holes for canning |
| 16 | Stiffener bottom |
| 17 | Back rest |
| 18 | French polishing to the repaired chair dining in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 19 | Recaning of repaired chair dining with best quality of approved plastic cane of white or cream ivory all as specified on drawingor as directed by Engineer-in-charge. |
| 20 | Chair writing(Drg No. FD-20,202,250, 280 ) : Removing of old unserviceable the following parts from chair writing, and supply and fixingnew same parts of hard wood duly finished with existing shape and fixed with bamboo pin and fevicol including tightening of other joints and applying 2 coats of french polish after preparation of existing surfaces complete all as shown on drg and as directed by Engineering-in-charge |
| 21 | Front legs (L&R) |
| 22 | Rear legs (L&R) |
| 23 | Side rail with holes (L&R) side for canning |
| 24 | Front and back siderails with holes for canning |
| 25 | Stiffener bottom |
| 26 | Back rest |
| 27 | Hand rest |
| 28 | French polishing to the repaired chair writing in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 29 | Recaning of repaired chair writing with best quality of approved plastic cane of white or cream/ivory all as specified on drawing or as directed by Engineer-in-charge. |
| 30 | Chair easy (Drg No. FD-17,201,229) : Removing of old unserviceable the following parts from chair easy, and supply and fixingnew same parts of hard wood duly finished with existing shape and fixed with bamboo pin and fevicol including tightening of other joints and applying 2 coats of french polish after preparation of existing surfaces complete all as shown on drg and as directed by Engineering-in-charge |
| 31 | Front legs (L&R) |
| 32 | Rear legs (L&R) |
| 33 | Side rail with holes (L&R) side for canning |
| 34 | Front and back rails with holes for canning |
| 35 | Back rail top and bottom of frame with holes for canning as per drg |
| 36 | Back rail ( L&R) back frame with holes for canning as per drg |
| 37 | Stiffener bottom |
| 38 | Hand rest |
| 39 | French polishing to the repaired chair easy in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 40 | Recaning of repaired chair easy with best quality of approved plastic cane of white or cream/ivory all as specified on drawing or as directed by Engineer-in-charge. |
| 41 | CHAIR DINING WITH CUSHION (Drg No. TP, FD/E6/MAP/10 ):S&F of following existing old brokenwooden components ofchair dining similar items carefully without disturbing the adjoining parts and new components made out ofhard wood in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, gluing, placing every part in-tact all as specified in Drg and directed by Engr - In Charge. |
| 42 | Back rest Stiffener |
| 43 | Bottom leg stiffener |
| 44 | Front legs |
| 45 | Rear Legs |
| 46 | Rubber/PVC shoes |
| 47 | Replacement of cloth for seat of repaired chair dining with cushion best quality of approved cloth of various all as specified on drawingor as directed by Engineer-in-charge. |
| 48 | Replacement of cloth for back of repaired chair dining with cushion best quality of approved cloth of various all as specified on drawingor as directed by Engineer-in-charge.(for TP Chair Dining with cushion only) |
| 49 | M&L for preparation of wooden surfaces of chair dining with cushion by scraping with sand paper, re-dusting and apply putty wherever required and polishing the surface with french polish to get glossy finish all as directed by Engr-in-Charge. |
| 50 | Side Board ( Drg No. FD-26, 241, 371 ) : |
| 51 | Removing old unserviceable / broken top from side board S/F New Top of 18mm thick pre laminate particle board Ex grade BWR of approved shad, ISI mark and fixing in potion including 4mm thick 1st class H.W beading all around the Top all as shown in drg and as directed by Engineer-in-charge |
| 52 | Removing of old unserviceable broken shutter from side board and supply and fix new shutter of 18 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour including 4 mm thick hard wood beading around the top and fixing in position with piano hinges all as shown on drg and as directed by Engineer-in-charge. |
| 53 | Removing of old unserviceable particle board (L&R) side from side board and supply and fix new L&R side pre-laminated particle board 18mm thick of approved shade and fixing in position all as shown on drg and as directed by Engineer-in-charge. |
| 54 | Removing old unserviceable back ply from side board S&F back ply of 6mm thick both side commercial, ISI mark and fixing in position all as shown un drg & as directed by Engineer-in-charge. |
| 55 | Removing old unserviceable leg from side board S&F New ledges of Hardwood and fixing in position with screw / Nails all as shows on drg and a directed by Engineer-in-charge. |
| 56 | Removing old unserviceable / broken knob from side board S&F New knob of 38 to 40mm dia plastic knob and fixed with required screw all as shown on drg & as directed by Engineer-in-charge. |
| 57 | Removing old unserviceable drawer from side board and S&F New drawer in position all as shown on drg & as directed by Engineer-in-charge. |
| 58 | M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of side board. |
| 59 | SOFA SET 1/4/ 5 PERSON WITH CUSHION (Drg No. FD-281, FD/E6/MAP/10 ) |
| 60 | Removing the existing unserviceable tapestry cloth, cushion of sofa set and replacing with new tapestry cloth including mulmul with foam cushion 40 density 100mm thick of size 558mm x 533mm x 100mm, rest all as shown on drg and as directed by Engr-in-Charge.Note :- (i) Each cushion for seat or back will be measured as single unit.(ii)The tapastrycloth shall be mat finish and shall not less than Rs. 350/- per metre and as approved by Engr-in-Charge. |
| 61 | Removing the existing unserviceable tapastry cloth of sofa set and replacing with new tapastry cloth mat finish of size 558mm x 533mm x 100mm with mulmul cloth. |
| 62 | Removing the existing unserviceable front leg from Sofa and providing new hard wood ofleg size 70mm x 35 mm x 300mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 63 | Removing the existing unserviceable rear leg from Sofa and providing new hard woodleg size as shown on drg and as directed by Engr-in-Charge. |
| 64 | Removing existing unserviceable Arm restfrom Sofa and providing new hard woodArm Rest of size as shown on drg and as directed by Engr-in-Charge. |
| 65 | Removing existing unserviceable side railfrom Sofa and providing new hard wood side rail of size as shown on drg and as directed by Engr-in-Charge. |
| 66 | Removing existing unserviceable bearerfrom Sofaand providing newhard wood bearer of sizeas shown on drg and as directed by Engr-in-Charge. |
| 67 | Removing existing unserviceable battensfrom Sofa and providingnewhard woodbattens of size 50mm x 20 mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 68 | Removing existing unserviceable front railfrom Sofa three seater and providingnewhard wood front rail of sizeas shown on drg and as directed by Engr-in-Charge. |
| 69 | Removing existing unserviceable front rail from Sofa single seaterand providingnew hard woodfront rail of size as shown on drg and as directed by Engr-in-Charge. |
| 70 | M & L for fixing of PVC shoes superior quality with fixing of screws as specified & directed by Engr-in-charge. |
| 71 | M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of sofa set 4 Seater and as directed |
| 72 | M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of sofa set 5 Seater and as directed |
| 73 | TABLE CENTER TWO TIER(Drg No. FD/MAP/08, 393) : The following repair shall be carried out to Table centre two tier after removing old UNSV parts and replacing with new parts of well seasonedhard wood free from pits & Knots as under complete all as specified under directed:- |
| 74 | Leg |
| 75 | Long Rail |
| 76 | Short Rail |
| 77 | Centre stiffner |
| 78 | Rubber/PVC shoes |
| 79 | Removing of unserviceable/ broken top from table centre two tier supply and fix new top of table centre two tier of prelaminated particle board of 18 mm thick BWRexterior grade ISI ma withTeak wood beading all around the top duly polished all as shown on drg and as directed |
| 80 | French polishing to the repaired Table Centre two tier with two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 81 | Table centre (Drg No. FD-29,235,274) Removing of old unserviceable the following parts from table centresupply and fix new following parts of hard wood duly finished in shape and tightening of other joints duly polished after repair work size all as shown on drg and as directed by Engineer-in-charge. |
| 82 | Front and back rails of centre table |
| 83 | Side rails ( L&R) |
| 84 | Legs for table centre |
| 85 | Stiffener |
| 86 | Removing of unserviceable/ broken top from table centre two tier supply and fix new top of table centre of prelaminated particle board of 18 mm thick BWRexterior grade ISI mark withTeak wood beading all around the top duly polished all as shown on drg and as directed |
| 87 | French polishing to the repaired Table centre in two coats after preperation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 88 | Tea poy(Drg No. FD-34,232,278, 382)Removing of old unserviceable the following parts from tea poy, and supply and fix new following parts of hard wood duly finished in shape in existing position of sizeall as shown on drg and as directed by Engr-In Charge. |
| 89 | Front and back rails of table |
| 90 | Side rails ( L&R) |
| 91 | Legs |
| 92 | Stiffener |
| 93 | Removing of unserviceable/ broken top from tea poy fabrication and fixing top of pre-laminated particle board of18 / 19 mm thick BWRexterior grade ISI mark including supply and fixing of 4 mm thickfirst class hard wood teak wood beading around the top duly polished all as shown on drg and as directed |
| 94 | French polishing to the repaired Teapoy in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 95 | Table peg(Drag No. FD- 25,236,266, 277,384)Removing of old unserviceable the following parts from table pegsupply and fix new following parts of hard wood duly finished in shape and tigheting of other joints duly polished after repair work all as specified in drg and as directed by Engineer-in-charge. |
| 96 | Front and back rails of table |
| 97 | Side rails ( L&R) |
| 98 | Legs |
| 99 | Stiffener (Bottom) |
| 100 | Removing of unserviceable/ broken top from table peg fabricating and fixing of top of pre-laminated particle board of 18 mm thick BWRexterior grade ISI mark including supply and fixing of 4 mm thick teak wood beading around the top duly polished all as shown on drg and as directed |
| 101 | French polishing to the repaired Table Peg in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 102 | Table 3\" x 2\" with or without drawer (Drg No. FD-41,224,283, 42,209,223, 231,284) :Removing of old unserviceable the following parts from table 3\" x 2\" with or without drawer and supply and fix new following parts of hard wood duly finished in shape and tightening of other joints duly polished after repair work all as specified in drg and as directed by Engineer-in-charge. |
| 103 | Front and back rails |
| 104 | Side rails |
| 105 | Legs |
| 106 | Stiffener |
| 107 | New drawer |
| 108 | Removing of unserviceable/ broken top from table 3\"x 2\" with or without drawer of pre-laminated particle board of 18mm thick one side teak faceexterior grade ISI mark fabricating and fixing on the frame of table 3\" x 2 \" sizeincluding4 mm thickteak wood beading around the top duly polished after repair work all as shown on drg and as directed by Engineer-in-charge. |
| 109 | French polishing to the repaired Table 3\" x 2\" with or without drawer in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 110 | Table writing(Drg No. FD-33, 249, 268,275) :Removing of old unserviceable the following parts from table writingsupply and fix new following parts and fixing in same positionall as shown on drg and as directedby Engineer-in-charge. |
| 111 | Removing of unserviceable top from tablewritingand supply and fix new top of 18 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour including 4 mm thick of teak wood beading around the top duly fixing in position including polishing after repair wok all as shown on drg and as directed |
| 112 | M&L for removing old u/s legs and S&F new legs made out ofteak wood duly finished/ smoothened complete all as specified & shown in drg and as directed. |
| 113 | Removing of old unserviceable side stiffener from table writing and ply and fixing new stiffener made from seasoned hard woodduly finished with existing shape as per respective drawings in position with screw/nails all as shown on drg and as directed. |
| 114 | Removing of old unserviceable bottomstiffener from table writing and supply and fixing new bottom stiffener made from seasoned hard woodduly finished with existing shape as per respective drawings in position with screw/nails all as shown on drg and as directed. |
| 115 | M&L for removing old u/s drawers and S&F new drawers complete all as specified & shown in drg. |
| 116 | Replacement of shutter of18 mm thick pre-laminated particle board with knob of 38 to 40 mm dia reqd as per drg |
| 117 | M & L for Replacement of left/right side of box of table of 18 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour as specified. |
| 118 | M & L for Replacement of back side ply 6 mm thick for box of the table writing as specified in drg. |
| 119 | M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of French polish to old and new surface of table and as directed |
| 120 | TABLE Dining 3\"x3\" (900x900) (Drg No. FD-88/291) : Repair to table dining 3\"x3\" (OR\"s) including dismantling/removal of all broken parts and replacing with new parts of hard wood as under complete all as specified under directed:- |
| 121 | Top made out of 18mm thick pre laminated particle board shade and texture as approved by engineer in charge with matching hard wood edging. |
| 122 | Leg made out of hard Wood |
| 123 | Long Rail made out of hard Wood |
| 124 | Short Rail made out of hard Wood |
| 125 | S& F new bracket of size 100 x 100 x 30 mm made of 1st class hard wood and fixing with 02 Nos suitable size steel screws complete as directed by Engr-in-charge |
| 126 | stiffener made out of hard Wood |
| 127 | Rubber/PVC shoes |
| 128 | M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table and as directed |
| 129 | TABLE DINING 4 PERSON (1200X900) (Drg No.FD - 273 ) : Repair to table dining 4 pers including dismentalling/removal of all broken parts and replacing with new parts of hard wood as under complete all as specified under directed:- |
| 130 | Top made out of 18mm thick pre laminated particle board shade and texture as approved by engineer in charge with matching Indian Teak wood edging. |
| 131 | Leg made out of hard Wood |
| 132 | Long Rail made out of hard Wood |
| 133 | Short Rail made out of hard Wood |
| 134 | S& F new bracket of size 100 x 100 x 30 mm made of 1st class hard wood and fixing with 02 Nos suitable size steel screws complete as directed by Engr-in-charge |
| 135 | Centre stiffener made out of hard Wood |
| 136 | Rubber/PVC shoes |
| 137 | M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table and as directed |
| 138 | Table dining 6 persons (Drg No FD- 239, 269, 273, 376) : Removing of old unserviceable following parts from table dining 06 pers and supply and fix new following parts of hard wood duly finished in shape in fixing in position with new bamboo pins and fevicol all as shown on drg and as directed by Engr-In-Charge. |
| 139 | Front and back rails |
| 140 | Side rails |
| 141 | Legs |
| 142 | Stiffener bottom |
| 143 | Bottom support |
| 144 | S& F new bracket of size 100 x 100 x 30 mm made of 1st class hard wood and fixing with 02 Nos suitable size steel screws complete as directed by Engr-in-charge |
| 145 | Removing of unserviceable top from table dining 06 persons and supply and fix new top of 18 / 19 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour includingteak wood beading around the top all as specified and directed. |
| 146 | M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table and as directed. |
| 147 | Table dining 8 persons (Drg No. FD-273, 376): Removing of old unserviceable following parts from table dining 08 pers and supply and fix new following parts of hard wood duly finished in shape in fixing in position with new bamboo pins and fevicol all as shown on drg and as directed by Engr-In-Charge. |
| 148 | Front and back rails |
| 149 | Side rails ( L&R) |
| 150 | Legs for table dining 08 pers |
| 151 | Stiffener bottom |
| 152 | Support for table bottom of the top |
| 153 | Removing of unserviceable top from table dining 08 persons and supply and fix new top of 18 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour including first class hard wood teak wood beading around the top duly polished after complete of repair work, all as shown on drg and as directed |
| 154 | Applying of French polishing to the Table dining 8 persons in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge. |
| 155 | TABLE DRESSING LADIES (Drg No. FD-32(M), 251) |
| 156 | S&F in repairs table top of Table dressing ladies with 18 mm thick pre-laminated particle Board of approved make, all as specified on drawing or as directed by Engineer-in-charge. |
| 157 | S&F in repairs new Glass shuttrs of Table dressing ladiesall as specified on drawing or as directed by Engineer-in-charge.(Each glass shutter shall be measured as single unit) |
| 158 | M & L for complete Lower box made out of Prelaminated particle board with drawer all etc complete all as per drawingas specified & as directed by Engr-in-Charge:-(back shall be 06 mm ply) |
| 159 | M&L for removing old u/s broken looking mirror and S&F new looking mirror of size 760 x 380 x 5mm & frame made out of teak wood of size 25 x 6 mm & 6mm thick commercial ply on back including polishing the frame complete all as directed. |
| 160 | Supply & fixing of Knob of aluminium anodized dark brown in shade as approved and fixing with screws as specified & as directed by Engr-in-Charge:- |
| 161 | M & L for fixing of PVC shoes superior quality fixing with screws as specified & directed by Engr-in-charge. |
| 162 | M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table and as directed |
