|
| 1 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed WorkPVC Pipes:(Dia) 15 mm |
| 2 | 20mm |
| 3 | 25 mm |
| 4 | 32mm |
| 5 | 40mm |
| 6 | 50mm |
| 7 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 8 | Supplying, fitting and fixing low-down cistern parts.(i) Internal fittings for cistern complete of approved make. (ii) Outlet Assembly |
| 9 | (ii) Outlet Assembly |
| 10 | (iii) Intlet Assembly |
| 11 | (iv) Rubber Kid |
| 12 | Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets.(a) Sink only (ii) 630 mm X 550 mm X 180 mm |
| 13 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. (iii) 600 mm long |
| 14 | Supplying, fitting and fixing bib cock or stop cock. (e) PTMT (Polytetra Bib Coc/ kSto p Cock ( Prayag or equivalent) 15 mm |
| 15 | Supplying, fitting and fixing pillar cock of approved make. b) PTMT Pillar Cock - 15 mm. (Prayag or equivalent). |
| 16 | Supplying of PVC water storage tank of approved quality with closed top with lid multilayer(c) 1500 litre capacity |
| 17 | (d) 2000 litre capacity |
| 18 | Labour for hoisting plastic water storage tank. (i) Upto 1500 litre capacity. (a) Upto 1st story from G.L. |
| 19 | (b) Extra for each additional story |
| 20 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 21 | Removing sludge from septic tank, soak well etc. by methor labour including disposal of the same outside the compound as directed. (a) Upto 20 users:- (i) Within a lead of 150 metre |
| 22 | Cleaning soak pit by removing the top slab and replacing inner filling with jhama bats and repairing the pit as necessary including fitting the slab. |
| 23 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (iii) 75mm. X 40mm. X 1.12mm. |
| 24 | (viii) 100mm. X 75mm. X 3.50mm. |
| 25 | i) Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete.(b) Medium (I.S.I. size 2) |
| 26 | Anodised aluminium barrel /tower /socket bolt (full covered) of approved manufactured from extrudedsection conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:(iii) 100mm long x 10mm dia.bolt. |
| 27 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.(a) With \"P\" trap |
| 28 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete.(a) E.W.C. (ii) Plastic (hallow type) white |
| 29 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15,mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out theframe. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer‟s specification and direction of Engineer-in-Charge. |
| 30 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles & rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding allnecessary hardwares as per direction of Engineer-in-Charge. |
| 31 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).(e) Sal : Malayasian |
| 32 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes.Pakur variety |
| 33 | Brick work with 1st class bricks in cement mortar (1:6)(b) In superstructure, ground floor. |
| 34 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 35 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar(c) 15 mm thick plaster |
| 36 | Clearing compound premises of shurbs, plants,jungles etc. by cutting and removing as directed (Specific permission of Engineer-in-Charge prior to execution will be necessary). (Payment to be made on area cleared) |
| 37 | Iron door handle of approved quality fitted and fixed complete: |
| 38 | Supplying heavy duty hydraulic double action floor spring along with top pin/set of pivots conforming to IS: 6315 or any approved make as per direction of Engineer in charge |
| 39 | Supplying concealed type heavy duty PVC headed aluminium tower bolt for double leaf doors as per approved make and brand as per direction of Engineer-in-Charge. b) 250 mm long |
| 40 | b) 450 mm long |
| 41 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.iv) 5mm thick coloured / tinted / smoke glass. |
| 42 | vi) 6mm thick coloured / tinted / smoke glass. |
| 43 | Supplying PVC rollers for sliding windows as per direction of Engineer in charge. |
| 44 | Supplying maruti lock (100mm) |
| 45 | A) Supplying Aluminium casted body hydraulic door closer as per I.S.I. |
| 46 | Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP) (b) 4mm thick (0.50mm Al.+3.0mm LDPE +0.50mm Al. PVDF coating) |
| 47 | (i) Door stopper.(Brass) |
| 48 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1 92 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete A) UPVC Pipes:(ii) 110 mm. Dia. |
| 49 | B) UPVC Fittings: d) Shoe (ii) 110 mm. Dia. |
| 50 | Uprooting and removing plants from the surface of walls parapet etc and making good damages. (Repairing of damages to be paid separately). (a) Small plant of girth of exposed stem upto 75 mm. liftupto 6 mtr. |
| 51 | Labour for cleaning |
| 52 | Carpenter ordinary |
| 53 | Add GST 18% over the Sub-Total upto item No. 36 |
| 54 | Labour Welfare CESS 1% over the Sub-Total upto item No. 38 |
