|
| 1 | Earth-work Excavation in trenches for foundations pipes, cable etc,(Loan clay or sand) including lift upto 1.5m lead upto 50m. And dressing of sides and rammingof bottom and disposal of surplus excavated earth as directed by the Engineer i/c within ahead of 30m. |
| 2 | Construction of Granular Sub-Base by providing Closegraded material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with Vibratory roller to achieve the desired density, complete as per technical clause 401 |
| 3 | Providing, laying, spreading and compacting graded stone aggregate in layers Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. |
| 4 | Providing and applying primer coat with SS2 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70to 1.00 kg/sqm using mechanical means. |
| 5 | Providing and laying dense graded bituminous macadam Grade II with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder VG-40 @ 4.5 per centby weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects. |
| 6 | Providing and applying tack coat with bitumen (VG-10) using Bitumen pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. |
| 7 | Providing and laying bituminous concrete with hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 5.4% of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects |
| 8 | Providing and laying of hot applied thermoplastic compound 2.50 mm thick in 100mm widh including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.50 mm is exclusive of surface applied glass beads as per IRC:35. The finished Surface to be level, uniform and free from streaks and holes. |
| 9 | Cat Eye (Raised Pavement Marker/Road Stud) Sharp Curve and Abadi Portion.Supply and fixing of reflectiveRaised Pavement marker With Its body surface made of tough ASA (Acrylic Styrene Acrylonitrite)or HIPS (Hi impact Polystyrene)oe ABS (acrylonitrile butadiens styrene). The marker shall supported a load of 1335 Kg tested in accordance with ASTMD 4280and its reflective pannel shall consist of number of lenses containing single or dual prismatic cubes of providing total internal reflection of light entering the lencs face .retro reflective surface shall be perferably be 35+-5 degree to the base and area of retro reflecting surface Shall not be less than 13.00 sqcm road stud shall be legibly marked with name trade mark or other means ideentification of the manufacture. Dimension of road Studs should not b less than 100mmx100mmx10mm. as per MORTH-804(8.35) suggesive Specification. (With shank) as per ASTM |
| 10 | Transverse Bar (Repeated Bars) for Speed Calming (Thermo Plastic Paint) Providing and Applying Hot applied thermo plastic compound 5 mm thick including reflectorising glass beads @ 500 gm /sqm area. Thickness of 15 mm is excusive of surface applied glass beads as per IRC 35. The finish surface tu be leveled uniform and free streaks and holes. Composition of thermo plastic material shall be as per table 800-3 of clause 803 of MORTH including cost of all material labour T&P etc required for proper completion of work as directed by E/I. |
| 11 | Providing and fixing of retro-reflectorised cautionary, mandatory and Informatory sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to th ground by means of properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground Ievel as per approved drawing (as per IRC:67-2022 clause 14.60) 90 cm equilaterial triangle including all material , labour, T&P, labour cess, all taxes etc but excluding GST. |
| 12 | Supply, fixing & eraction of built up Cantilever Structure 6m span comprising of one vertical posts of 6.00 m height made up of 300mm NB heavy class MS pipe as vertical member welded with 10 mm MS plate at top & 12mm plate of bottom. The horizontal Truss shall comprise of 50mm dia heavy class MS pipe and 40 mm dia heavy MS pipe as bracing and 10 mm MS plate at bottom for fixing to vertical post as per structure design and drawing with one of steel primer and two coats of synthetic enamel plant. The work includes construction of RCC Foundation of Size 90X90m of required depth as per site condition for built up structure including Earth work in excavation 100mm thick lean concrete in 1:4:8 cement coarse sand and 40 mm guage stone ballast RCC withand 1:2:4 cement coarse sand and 20 mm stone grit including supply and fixing of 25mm dia Foundation Bolts 600 mm long as per provision of structure design including cost of reinforcement & shuttering. The lateral vertical clearances and complete. Installation work shall be as per relevant clauses of MORT&H specification section 800 and IRC 67:2010 complete in all respect. The Rates shall include cost of design fabrication supply, transportation, Local shifting Erection of Signage structure using crane, inclusive of all taxes royelty, VAT etc. all T&P machine, material and labour required for proper completion of work as per direction of E/I.) |
| 13 | Providing and fixing of Reflective Signs with a corrosion resistant 4mm thick aluminium composite panel face to be fully covered with High Intensity prismatic sheeting Type XI as per IRC 67:2010 retro reflective sheeting with MS angle frame of 35x3. as per morth 801 |
