Tender For Repair Maint Of Main Gate At Hq 28 Sect Ar Kakching Manipur
Tender Value
4.99 Lakhs
Estimated cost
Bid Submission
29 Apr 2025
0 days left
EMD
10000
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kakching → Manipur
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repair Maint Of Main Gate At Hq 28 Sect Ar Kakching Manipur
BOQ
| Sl. No. | Item Description |
| 1 | SCHEDULE‘A’ PART-I (Repair/Maint of Main Gate) |
| 2 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. completeHot finished seamless type tubes |
| 3 | Providing and fixing 50mm iron or M.S. Wheel or roller of steel door or gate and fitting and fixing the same with necessary clamps, nuts and bolts/welding and erection etc. complete. |
| 4 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 5 | Providing and fixing ISI marked oxidised M.S. sliding door 300x16 mm bolts with nuts and screws etc. complete : |
| 6 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work. |
| 7 | SCHEDULE‘A’ PART-II (Repair/Maint of Sentry Post at Main Gate) |
| 8 | Repairs to plaster of thickness 12 mm to 20 mm including cutting the patch in proper shape, raking out joints andpreparing and plastering the surface of the walls complete, including disposalof rubbish to the dumping ground, all complete as per direction of Engineerin-Charge.With cement mortar 1:4 (1cement: 4 coarse sand) |
| 9 | Repairs to plaster of thickness 12 mm to 20 mm in , including cutting the patch in proper shape, raking out joints andpreparing and plastering the surface of the walls complete, including disposalof rubbish to the dumping ground, all complete as per direction of Engineerin-Charge.With cement mortar 1:4 (1cement: 4 coarse sand) |
| 10 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade Old work (one or more coats) |
| 11 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 12 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work |
| 13 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:G.S. Sheet |
| 14 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 15 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete for Ridges plain (500 - 600mm). |
AI Tender Summary
Tender Timeline
Apr 17, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedApr 29, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 30, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender