Tender For Lighting And Other Repair Work On The Divider Behind King City Placio Mall., lucknow-Uttar Pradesh

Lighting and other repair work on the divider behind King City Placio Mall.; 1 Supply of Decorative Zig Zag Street light pole of height approximate 11 mtr high pole with double arm at heights of 11 mtr and 9 mtr respectively, as shown in drawing. Total pole length of 11 mtr of section of 12.436 mm length of 113.5 x 113.5x6 mm for a total height of 11 mtr in accordance to the drawing, with lumnaire mounting at 11 mtr and 9 mtr respectively. Pole made of MS square pipe of nominal wall thickness 6 mm + 10 % as per IS 4923:1997 standard. The pole shall have inbuilt junction box weather proof flush door junction cover fixing arrangement for pole at 600 mm above the base plate. Junction chamber of pole to accomdate 6 Amp MCB heavy duty connector block installed on bakelite sheet for inslulation from pole body. The pole shall be made of square hollow section (SHS) of 113.5 x 113.5 x 6 mm + 10 % for zig zag arm along with a heavy duty base plte dimensions 300 * 300 * 20 mm thickness. 8 rigid supports to connect pole to base plate to insure stability of pole to foundation plate and pole strength. (PRS CVD Plasio Mall) 2 Supply and fixing ofLED Street light Fittinghaving die cast aluminium body and diffuser with driver set suitable for 175 to 200 Watt. Confirming to IP 66Protection complete in all respects CAT-AAA (SI No 1425(a)/2018. 3 Supply and fixing offactory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 Watt. Confirming to IP 66 protection complete in all respect.CAT-AAA (SI No 1455(a)/2018. 4 Supplyandlayingof aluminiumconductorPVCinsulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. SIN. 501/2018 5 25 sq. mm 3-1/2 core 6 16 sq. mm 4 core 7 70 sq. mm 3-1/2 core 8 95 sq. mm 3-1/2 core 9 10 sq. mm 4 core 10 S/F of 40A. TPN capacity of automatic Street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 Series with contactors HRC fuses, isolating Switch metering instrument box with CTS etc. in case of TPN, Complete in all respect as per approval by E/Ic.(PWD, SOR-807-F/2018) 11 Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCBs (Four Pole 36 KA with thermal magnatic release)Switches Complete and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters(KVA,P.F,KW etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mountedon non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCBs shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc.The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubicle type switch board shall be of cat A & B Only. .(PWD, SOR-812/2018) 12 Incoming 200 Amp. MCCB-1 No 13 Outgoing100 Amp. MCCB-1 Nos. & 63 Amp MCCB-3 No 14 Supply and construction of RCC Plint for 12.5 mt. long high Mast. Rates are included required earth excavation , required CC/RCC/Plaster etc, proper completion of work as per direction of EI. (As per attached Detail) (PSR) 15 DismantlingFixing of 12.5 mtr High mast complete with all accessories . Rates are also included with all labour rate T&P and transportation of all materials from existing site to praposed site of C.G city. (Labour Rate =1x11000 + 1x11000= 22000)(PWD, SOR-651/2018)(PWD, SOR-651/2018) 16 Fixing of 12.5 mtr High mast complete with all accessories . Rates are also included with all labour rate T&P and transportation of all materials to praposed site of C.G city. (Labour Rate = 11000 for each)(PWD, SOR-651/2018) 17 Supply and fixing of outdoor type 415 volt TPN distribution feeder piller dust and vermium proof consisting copper busbar of 50mm x12mmor equivqlent cross sectional area 02 nos 500 amp henlay type fuse units as incoming 02 nos 500 amp and 0 no 300 amp henly type fuse units as outgoing metallic piller shaft be made of 14 SWG MS sheet on frame of angle iron of 35mm x 35mm x5mm with both side locking arrangement including painting with 02 coats of approved paints over rust resisting primer as per direction of E/I .( approved Rate ) 18 Supply and fixing suitable size ring for fixing of light fixture as per direction of E/Ic.PSR River Front 19 S/F of 1.5 HP Power motor complete with chain or etc. as per direction of E/IC.PSR River Front 20 S/F of steel rope complete in all respect as per direction of E/Ic. 21 Supply and fixing of 4 core multiflaxible copper wire PVC insulated complete in all respect.PSR River front 22 Laying of Armoured cable with HDD Drilling method complete with labour T&P etc.All as per direction by E/Ic. PSR Basantkunj Sec.-I

INR 2950 /-

INR 183200.0 /-

INR 35.63 Lakhs /-