Tender For 27022931,27022932,27022762, 27023601 _Cable Laying_ Bahadu 27022762 10 10 10 SERVICE CHARGES 1 LO Email : CHITRASEN.PRADHAN@AMNS.IN Contact : Name : Chitrasen Pradhan Item Details : Item Note : 2 27022931 10 20 10 REMOVAL/DISMANTING- CONTROL CABLE 50 M 30 INSTALLATION AND COMMISSION OF HT PANEL 1 NO 20 DISMANTLING OF LT PANEL 1 NO 50 SUPERVISION OF ERECTION & COMMISSIONING 7 TAG 40 INSTALLATION OF EARTHING STRIPS 25 M Email : CHITRASEN.PRADHAN@AMNS.IN Contact : Name : Chitrasen Pradhan Item Details : Installation and commissioning of 11KV,630A VCB at Bahadurgarh SSC. The following is the SOW In respect of terms <(>&<)> conditions, not explicitly provided in this Special Terms <(>&<)> Conditions, provisions of General Conditions of contract are applicable. Bidders are required to go through the tender document carefully before giving final quote for items mentioned in the attached list. If required, bidders can also visit our site for understanding the job properly; however, they should inform their program for site visit in advance to the contact persons. 1. Vendor Shall be experienced in Electrical erection and commissioning work. He should have all the authorization documents/ certificates to carry out Electrical work. 2. All work to be carried out as per safety norms which shall be guided to AM/NS team during work <(>&<)> no tolerance in safety will be accepted and penalty to be imposed if any violation. 3. Arranging the proper housekeeping after work completion <(>&<)> not leave the work site in an unsafe condition or any other condition that might cause injury to personnel, damage to existing work, plants, or equipment. 4. Verify all equipment’s before declared the work completion and should be certified by user. 5. Tools <(>&<)> tackles required to complete below said job will be in vendor’s scope. Dis connection / dismantling of exiting connection of control and cable connection as per instruction of AMNS Site Incharge. Dismantling of exiting LT panel <(>&<)> Shifting of old panel within switch board room and Shifting of new panel within switch board room as instructed by AMNS Site In charge. Installation and commissioning of HT panel and inter panel with Identification and marking of control and HT cable of exiting HT panel, connection of AC and DC auxiliary cable at panel side, connection of for transformer and motor ,Testing at site with site test reports. Connection of Coupling busbar and Hardware Installation of Earthing strips as per site condition or instructed by AMNS Site In charge. Earthing Strips shall be provided by AMNS. Supervision during erection, testing <(>&<)> commissioning. AMNS SAFETY RULES AND REGULATION AS PER COMPANY POLICY 1. All necessary safety PPE’s i.e., safety helmet, safety shoes, fluorescent jacket, leather gloves, goggles, welding face shield, Full body harness with double lanyards having scaffolding hooks, Insulated ladder for height work, etc. in contractor scope. 2. Damaged or modified PPE won’t be tolerated on the worksite. 3. Usage of mobile phones for contractor labour is strictly prohibited. Only Supervisor and contractor are allowed to carry mobile phone. 4. AMNS Safety golden rules are the baseline for safety of contractor manpower <(>&<)> Supervisor also. 5. The supervisor must conduct Safety Toolbox Talk (TBT) before starting their daily job on topics related to the nature of the job. 6. Work permit and work should be done in presence of Vendor’s safety supervision and site engineer. 7. The ladder will be anti-static and anti-skid in nature. That is there should be no static charge built up on the ladder while a person is performing work over it. Ladder should be stable enough to ensure the stability of person performing work at height. 8. Bamboo ladder won’t be entertained in any of the work. 9. If the ladder has wheels, make sure wheels of ladder should have wheel choke in it. Same will be applicable in case of mobile sca ffolding. 10. Pre safety inspection of ladder, scaffolding and working platform will be adhered. If any unsafe condition gets captured, work will not progress. 11. Maintain form 10- or third-party inspection certification of all lifting tools, tackles, and machinery. That is all lifting equipment should be inspected and certified by a competent person. 12. Strictly adhere to barrication. That is barricading the working area with safety cones and caution tape. 13. In case of gas cutting, strictly perform the pre safety inspection of gas cutting set and cylinders. Inspection will be carried out as per the provided checklist. 14. Provide flashback arrestor on both hoses used in gas cutting. Flash back arrestors will be adhered to the cutting set and cylinders. 15. Inspect the workplace before performing hot work. That is there should not be any combustible and flammable substance present nearby. 16. Strictly adhere to the protective guard in grinding machine. Do not bypass any guard which is the interface between the moving parts of machine and the person operating the machine. 17. Make sure all the persons performing work at height are fully insured as per the workmen’s compensation policy. A person performing work at height shall be both physically and mentally fit and should not suffer from any prolonged diseases or any type of phobia. 18. AMNS Safety In charge will do audit for all PPE’s <(>&<)> If any PPE missed, Vendor shall arrange the same. 19. All work to be carried out as per safety norms which shall be guided to AM/NS team during work <(>&<)> no tolerance in safety will be accepted and penalty to be imposed if any violation. 20. The contractor shall not proceed with the next activity until the previous activity will be checked and approved by the Representative. 21. All required tools <(>&<)> tackles will be provided by the contractor. 22. The contractor shall deploy and provide one full-time engineer to supervise the project and have experience of carrying out this type of work. 23. Contractor will provide all required consumable items for the job. 24. The contractor shall be responsible for procuring, supplying, transporting, and providing all labour, materials, tools and equipment etc., required for completion of the work. 25. All materials shall be stored in a proper manner protected from natural elements to avoid contamination and deterioration. 26. Workers working on the site shall be skilled in their job and have related job experience. 27. The contractor shall guarantee that all work performed will be free from all defects in workmanship and materials and that all installation will provide the capacities and characteristics specified. The contract further guarantees that if, for a period of one year from the date of the certificate of completion and acceptance of the work, any such defects will be repaired by the contractor at his own cost. 30 40 3C 240 SQMM 6.6KV HT CABLE GLAND & TERM 1 NO 120 FIXING OF EARTHING STRIP 50X6 MM 30 M 100 S&I OF GI EARTHING ELECTRODE 15 M 20 REMOVAL/DISMANTING- CONTROL CABLE 70 M 60 GLANDING & TERMINATION OF 4C*6SQMM CABLE 2 NO 80 ERECTION OF RTCC PANEL FOR TRANSFORMER 1 NO 50 CABLE LAYING 3C/4C X 6 SQMM 30 M 90 S&I OF COPPER BONDED EARTHING ELECTRODE 7 M 30 COMMISSIONING OF TRANSFORMERS 1 MON 10 DISMENTLING OF TRANSFORMER 1 MON 130 LIASONING WITH ELECTRICAL INSPECTOR 1 EA 70 CONTROL WIRING OF TRANSFORMER 1 LO 110 FIXING EARTHING STRIP 50 M Email : CHITRASEN.PRADHAN@AMNS.IN Contact : Name : Chitrasen Pradhan Item Details : Existing 2.5 MVA off load tap changer transformer replacement with 1.25 MVA On load tap changer transformer at Bahadurgarh SSC. The following is the SOW In respect of terms <(>&<)> conditions, not explicitly provided in this Special Terms <(>&<)> Conditions, provisions of General Conditions of contract are applicable. Bidders are required to go through the tender document carefully before giving final quote for items mentioned in the attached list. If required, bidders can also visit our site for understanding the job properly; however, they should inform their program for site visit in advance to the contact persons. 1. Vendor Shall be experienced in Electrical erection and commissioning work. He should have all the authorisation documents/ certificates to carry out Electrical work. 2. Vendor shall include Material handling equipment’s required to installation of transformer, team to <(>&<)> from charges, conveyance charges, lodging boarding charges etc. 3. All work to be carried out as per safety norms which shall be guided to AM/NS team during work <(>&<)> no tolerance in safety will be accepted and penalty to be imposed if any violation. 4. Arranging the proper housekeeping after work completion <(>&<)> not leave the work site in an unsafe condition or any other condition that might cause injury to personnel, damage to existing work, plants, or equipment. 5. Verify all equipment’s before declared the work completion and should be certified by user. 6. Tools <(>&<)> tackles required to complete below said job will be in vendor’s scope. 2.5MVA transformer dismantling and shifting including busduct and control cable. Existing transformer and VCB Control Cable disconnection as instructed by AMNS representative. 1.25MVA transformer erection and commissioning. Laying, Glanding, Lugging and termination of 3C X 240 Sqmm HT cable. Laying, Glanding, Lugging and termination of 4C X 6 Sqmm copper LT cable. Control cable laying, glanding, lugging and termination between Transformer and VCB and RTCC panel. Supply and fixing of HT termination kit. Control cable laying, glanding, lugging and termination between Transformer and VCB and RTCC panel. Fixing of RTCC panel with mounting frame. Structural Steel shall be provided by AMNS. Make sure all the persons performing work at height are fully insured as per the workmen’s compensation policy. A person performing work at height shall be both physically and mentally fit and should not suffer from any prolonged diseases or any type of phobia. 18. AMNS Safety In charge will do audit for all PPE’s <(>&<)> If any PPE missed, Vendor shall arrange the same. 19. All work to be carried out as per safety norms which shall be guided to AM/NS team during work <(>&<)> no tolerance in safety will be accepted and penalty to be imposed if any violation. 20. The contractor shall not proceed with the next activity until the previous activity will be checked and approved by the Representative. 21. All required tools <(>&<)> tackles will be provided by the contractor. 22. The contractor shall deploy and provide one full-time engineer to supervise the project and have experience of carrying out this type of work. 23. Contractor will provide all required consumable items for the job. 24. The contractor shall be responsible for procuring, supplying, transporting, and providing all labour, materials, tools and equipment etc., required for completion of the work. 25. All materials shall be stored in a proper manner protected from natural elements to avoid contamination and deterioration. 26. Workers working on the site shall be skilled in their job and have related job experience. 27. The contractor shall guarantee that all work performed will be free from all defects in workmanship and materials and that all installation will provide the capacities and characteristics specified. The contract further guarantees that if, for a period of one year from the date of the certificate of completion and acceptance of the work, any such defects will be repaired by the contractor at his own cost. 28. Vendors shall follow all guidelines <(>&<)> safety protocols provided by AMNS. 29. Vendors shall carry all PPE’s mentioned in AMNS safety policy. 30. Vendors shall follow Golden safety rules related to jobs only which are provided by AMNS. Item Note : 4 27023601 10 40 10 POWER CABLE LAYING/INSTALLATION 150 M Email : CHITRASEN.PRADHAN@AMNS.IN Contact : Name : Chitrasen Pradhan Item Details : Existing 2.5 MVA off load tap changer transformer replacement with 1.25 MVA On load tap changer transformer at Bahadurgarh SSC. The following is the SOW In respect of terms <(>&<)> conditions, not explicitly provided in this Special Terms <(>&<)> Conditions, provisions of General Conditions of contract are applicable. Bidders are required to go through the tender document carefully before giving final quote for items mentioned in the attached list. If required, bidders can also visit our site for understanding the job properly; however, they should inform their program for site visit in advance to the contact persons. 1. Vendor Shall be experienced in Electrical erection and commissioning work. He should have all the authorisation documents/ certificates to carry out Electrical work. 2. Vendor shall include Material handling equipment’s required to installation of transformer, team to <(>&<)> from charges, conveyance charges, lodging boarding charges etc. 3. All work to be carried out as per safety norms which shall be guided to AM/NS team during work <(>&<)> no tolerance in safety will be accepted and penalty to be imposed if any violation. 4. Arranging the proper housekeeping after work completion <(>&<)> not leave the work site in an unsafe condition or any other condition that might cause injury to personnel, damage to existing work, plants, or 20. The contractor shall not proceed with the next activity until the previous activity will be checked and approved by the Representative. 21. All required tools <(>&<)> tackles will be provided by the contractor. 22. The contractor shall deploy and provide one full-time engineer to supervise the project and have experience of carrying out this type of work. 23. Contractor will provide all required consumable items for the job. 24. The contractor shall be responsible for procuring, supplying, transporting, and providing all labour, materials, tools and equipment etc., required for completion of the work. 25. All materials shall be stored in a proper manner protected from natural elements to avoid contamination and deterioration. 26. Workers working on the site shall be skilled in their job and have related job experience. 27. The contractor shall guarantee that all work performed will be free from all defects in workmanship and materials and that all installation will provide the capacities and characteristics specified. The contract further guarantees that if, for a period of one year from the date of the certificate of completion and acceptance of the work, any such defects will be repaired by the contractor at his own cost. 28. Vendors shall follow all guidelines <(>&<)> safety protocols provided by AMNS. 29. Vendors shall carry all PPE’s mentioned in AMNS safety policy. 30. Vendors shall follow Golden safety rules related to jobs only which are provided by AMN
