Tender For Special Heating Work Of Pw-03 (Time-4) House At Janagar Jaunpur. - Removing white or colour wash by scraping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. As per DSR 13.88 2 12 mm cement plaster of mix : 1: 6 (1 cement : 6 coarse sand) 3 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 4 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 5 M.S. or Iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. 6 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. 7 Providing & fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos cement sheet ground fixed to wooden cleats with C.P. brass screws and washers. DSR 17.31 8 Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. DSR18.48 9 Providing and fixing C.P. Brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810gms. 15mm nominal bore. AS per SOR 18.50 10 Providing and fixing G.I. Union in G.I. Pipe including cutting and treading the pipe and making long screws etc. complete (New work). 20mm nominal bore.AS per SOR 18.46 11 Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00m spacing. This ncludes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. internal work. exposed on wall. 20mm nominal outer dia pipes. As per SOR 18.7 12 Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings.Thisincludes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge. external work. 25 mm nominal outer dia Pipes DSR 18.9.3 13 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.15 mm nominal outer dia PipesDSR 18.9.3 14 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal boreDSR 18.49.1 15 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture 16 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 17 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer 18 Finishing walls with Acrylic smooth exterior paint of required shade: - New work (Two or more coat applied @ 1.43 Ltr./10 Sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10 Sqm. 19 Providing and laying integral cement based waterproofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations : a) Applying a a slurry coat of neat cement using 2.75 kg/sq.m of cement admixed with waterproofing compound conforming to IS : 2645 and approved by engineer-in-charge over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement:5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by engineer in charge to required slope and treating similarly the adjoining walls up to 300mm height including rounding of junctions of walls and slabs. c) Aftertwo days of proper curing applying a second coat of cement slurry using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS:2645 and approved by Engineer in charge. d) Finishing the surface with 20mm thick joint less cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with waterproofing compound conforming to IS : 2645 and approved by Engineer incharge. d) Finishing the surface with 20mm thick joint less cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with waterproofing compound conforming to IS : 2645 and approved by Engineer in charge including laying glass fiber cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300 x 300 mm sqm. 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurra as 65mm 20 Providing and laying of 8 to 10 mm thick ivory or light shade vitrified tiles of 600 mm x600 mm size in flooring or skirt ing laid with 1:3 cement mortar (1 cement :3 coarse sand) finishing with cement slurry & with pigment grouting & polishing complete i/c supply of all materials, labour T &P required for proper completion of work. 21 Supply and fixing 6 mm China white glazedtiles in flooring or in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry jointing and polishing complete including supply of all materials, labour and tool sand plants etc. required for proper completion of the work. (Size of tiles upto 300x300mm). 22 Earth work in Excavation of Earth in foundatin etc complete As per 23 providing and laying of Plain cement concrite 1:2:4 As per 24 12mm thick plaster with cement mortar consisting of 1 part cement and 4 part of approved coarsesand. Minimum thickness not be less than 10mm including supply of all materials, labour and T&P etc. required for proper completion of the work. As per SI No. 25 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 26 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 27 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.With 12 mm mild steel U beading DSR 9.51.1 28 Mild steel or iron work in heavy sizes such as trusses, built up gates, record racks, roof work, gates etc. wrought to required from, including drilling holes riveting or welding where necessary &their fixing, required for proper completion of the work.( Including allmaterial, T&P , Labour Cess etc but Excluding GST).
