Name of Work: Replacement of MCHV light & Power Panel with allied work in I.I.M.C. Campus Joka.
Sl. No.
Item Description
1
Light PanelProviding a new Lightingpanel size in adequate size (H-1600 mm x W-1500 mm x D-350 mm), powder coated and smoke grey colour for MCHVbuilding in the Panel Room.The following materials are:-1)200 A TPN SFU unit -1 no,Make -Havells /L& T/ABB2)125 AMCCB -3 Nos. Make - L& T /Havell/ABB3)100 A MCCB - 2nos. Make - L& T /Havells/ABB4)200A copper bus bar - 4 nos5)Indication lamp (LED) - 3 nos6)Volt meter - 1 no (Make -AE)7)Volt meter selector switch -1 no Make-AE8) 63 A TPN MCB-4-nos. (Make - Havells/L&T/Hagger)9) 10/20 A SP MCB-12 nos(Make - Havells/L&T/Hagger)10)Internal wiring by 1.5 sq mm copper flexible wire for control wiring-40 meters (Make-Polycab) 11)Iron Angle Frame for setting right the Panel in trench12)Internal power line wiring by 10 sq mm copper flexible wire(Polycab/Finolex) from bus bar to MCCB & TPN MCB and DP MCB - 90 Meters (approx) with proper copper lugs.13)Fabrication work and Painting
2
Power PanelProviding a new powerpanel size in adequate size (H-1600 mm x W-1800 mm x D-350 mm), powder coated and smoke grey colour for MCHVbuilding in the Panel Room. (Interlocking sys. From power to light and light to Power)The following materials are:-1)250 A TPN SFU unit -1 no(Make –Havells /L& T/ABB)2)125 A MCCB - 4 Nos. Make- L& T /Havells/ABB3) 200 A 4-Pole change over switch -1 no.with mechanical interlocking Make- Havells/Hagger/ABB4) 200A Copper bus bar-4 nos5)Indication lamp (LED)- 3 nos6)Volt meter- 1 no (Make -AE)7)Volt meter selector sw.-1 no (Make-AE)8) 63 A TPN MCB - 4 nos (Make - Havells/L&T)9) 10/20 A SP MCB-9 nos and 40 A DP MCB-4 nos (Make - Havells/L&T/ABB)10)Internal wiring by 1.5 sq mm copper flexible wire for control wiring - 40 meters (Make-Polycab) 11)Internal power line wiring by 10 sq mm copper flexible wire from bus bar to MCCB & TPN MCB. -100 Meters.( approx ) with proper copper lugs.12)Iron Angle Frame for setting right the Panel in trench13)Fabrication work and Painting
3
Installation of the above power and lighting panel in the same location as per electrical norms. And Dismantling the existing panel in proper way to diposite the engg. Divn godwn.
4
Proper connectivity of existing cable in the newly Proposed panel with proper socketing.
5
Preparation of earthing withGI pipe and earth strip (25 x 6)as per I.E rule i.e salt charcoal etc. sch. CPWD-2022,P-23, CODE-5.1
6
Supply and laying 25 x 5 mm GI Strip for the earthing connectivity from Feeder box to earthing pipe with proper nut bolt etc. CPWD-2022, P-24, code-5.15
7
Supply & laying of 2 x 2.5 sq mm copper wire for LED Light fixing ( Anchor/Polycab/Finolex)
8
Supply & Fixing 150 w Flood light. (Philips/Crompton/Bajaj)
9
Supplyof 3.5c x 70 sq mm AlumininumArmored cable (Polycab/KEI/Havells)
10
Laying the same cable in under ground as per CPWD Schedule, P-26,2022 code-7.1.2
11
Supply & fixing of 160 A SFU TPN Main switch for outgoing LVH pump room. (Havells/L&T/ABB).
12
Supply & laying 2inch dia GI pipe for the protection of cable. (Tata/Jindal/Bansal).
13
Supply & fixing of End termination with gland. As per CPWD 2022, P-29, code-9.1.23
14
Any miscellaneous work not covered in present schedule but required to be done on a as and when basis will be executed by the contractor . Work value will be ascertained based on rate analysis / orginal bill submission . 10% profit will be paid on orginal bill value submitted . The work will be done as per direction of engineer- in -charge.
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
