|
| 1 | Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etcandremoval of entire debris as ordered outside MD land complete all as directed. |
| 2 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level andremoval of entire debris as ordered outside MD land complete all as directed. |
| 3 | Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris to a distance not exceeding 50 mts and depositing where directed. |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 5 | Dismantling of ACCorrugatedor semi corrugatedsheet etcanythicknessincluding ridges as in roof covering and stacking at site where directedand removal of debris to a outside MOD land and depositing where directed complete all as directed.Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified and as directed. |
| 6 | Providingcement concrete Type B1 1:2 :4 using 20 mm graded crushed stone aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),string courses, copings. kneelers, apex stones, pier caps, columns, posts , boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets,etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match Set in cement mortar 1:4 completeall as directed. |
| 7 | M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified. |
| 8 | Supply onlyIntegral Water Proofing Compound (ISI Marked) liquid of Make : CICO,Acco Proof, Impermo, Aqua flex as approved. |
| 9 | S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Grade E-250 quality ‘A’ all as specified and as directed. |
| 10 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed |
| 11 | Supply and fix Pre- painted galvalume aluminum zinc coating GI plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction all as specified and as directed. |
| 12 | Dismantling ofany type ofdamaged ceiling boardsfixed in any description & S&F 6 mm thickcalcium silicateboardof siliceous & calcareous materialreinforced with cellulose fibreboards as in ceiling fixed flatwith and including aluminium anodised snap Grid 605 x 605 mm frame work using 36.50 x 23.50 x 1.5mm main Tee, 23.50 x 23.50 x 1.5mm cross Tee and 25x25x1.5mm angles fixed to wall for ceiling incl necessary supporting hanger with 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm longfor securing frame work to ceiling suspended at 120cm etc. both way. (Size of grid shall be 605mm x 605mm) including 6mm thick buildingboardasdescribedfixing with clips etc.and ceiling baord fixed as per manufacturerrs instructions complete alll as directed. (Note The quoted rate is deemed to be incluvise of non asbestosboard , aluminium snap grid & susupenders complete) |
| 13 | Material and labour for removal of existing WPT course or any other kind of treatment surface over roof slab and cleaning ofsurface with wire brushes and water removing of unsolvent materials and depositing of the same outside MoD land and provide 10 mm thick screed bed/ bedding layer in CM 1:4 mixed with Water Proofing Compound (WPC) as per manufacturer instructions, including finishing the surface fair and even on RCC roof/ parapet once bedding layer of concrete is completely dried and apply oil bound bituminous primer @ 0.20 Kg/Sqm and providing 4mm thick APP modified water proofing membrane weighing not less than 4.00 Kg/Sqm reinforced with non woven polyster matt weighing not less than 160 gms/Sqm including minimum 10 cm side over laps and 15 cmend lap torch sealed and bonded as per detailed procedure as directed, apply a coat of blown grade hot bitumen 90/15grade over the membrance @1.2 Kg/Sqmand finally finished the top surface with solar reflective bituminious aluminium @0.10 Kg/Sqmcomplete all as specified and as directed.Note: (i) The quoted rate is deemed to be inclusive of taking down & removal of debris , 10 mm thick 1:4 screed & complete APP treatment. (ii) WPC will be paid seperately (iii)The work shall be carried out only through manufacturer or their authorised applicator and a written guarantee for work shall be submitted by the manufacturer for the effectiveness of WPT (iv) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. |
| 14 | M&L for rendering 15 mm thick in CM 1:6 on brick work/ block concrete surfacefinished the surface even and smooth without using extra cement complete all as specified. |
| 15 | M&L forrendering 15 mm thick in cement mortar 1:4 on fair faces of brick work/ stone work or concrete surfaces mixed with WPC as per manufacturer instruction, and finished the surface fair and even complete all as specified and directed. |
| 16 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc complete ll as directed. |
| 17 | M&L preparing new plastered wall surfaces & apply distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. Two or more coats over a coat of 1 to 2 mm thick Birla white cement based wall careputty complete all as specified. |
| 18 | M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation ofnew steel surface complete all as directed. |
| 19 | Taking down old rusted / wornout 25 mm bore GI tubing after necessary disconnection & S&F new 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed. |
| 20 | Taking down old rusted / wornout any dia of tubing after necessary disconnection & S&F new 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed. |
| 21 | S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified including dismantling & taking down old unserviceable 110mm bore PVC pipe with fittings |
| 22 | Disconnecting existing tanks, setting aside ( for lowering if required) for repairs, cleaning,etc and hoisting if requiredreconnecting and refixing in positing including cleaning and removing all scale and dirt,etc from tanks and from mouths of circulating pipes. ( Capacity exc 500 lts but not exc 1000ltrs) |
| 23 | Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site andS&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical verticalwith close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, fixture hoisted and fixed in position where orderedand making necessary connection and testing complete all as directed. |
| 24 | Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site andS&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical verticalwith close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, fixture hoisted and fixed in position where orderedand making necessary connection and testing complete all as directed. |
