|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | a)Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level |
| 4 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 5 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 7 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) |
| 8 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 9 | Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. |
| 10 | Wedge expansion type Fastener with threaded dia 12 mm |
| 11 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Sal wood |
| 12 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneeringwith vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 13 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessarycomplete : 25 mm dia |
| 14 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 15 | 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) |
| 16 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer |
| 17 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 18 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With ready mixed pink or grey primer on wood work(hard and soft wood) having VOC content less than50 grams/ litre |
| 19 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work |
| 20 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A |
| 21 | Group A |
| 22 | Group A |
| 23 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 24 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 25 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 26 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 27 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 28 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 29 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch |
| 30 | 15/16 A switch |
| 31 | 3 pin 15/16 A socket outlet |
| 32 | 6 pin 15/16 A socket outlet |
| 33 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 34 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate asrequired. |
| 35 | Supplying and fixing of following ways surface/ recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) way (4 + 24), Double door |
| 36 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 37 | 63 A |
| 38 | Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V \"C\" curve DP MCB complete with connections, testing and commissioning etc. as required. |
| 39 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.with charcoal/ coke and salt as required. |
| 40 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 41 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm |
| 42 | Above 95 sq. mm and upto 185 sq. mm |
| 43 | Supply of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size for lying direct in ground with excavation, sand cushioning, protective covering and refilling the trench etc as required.a) 4.0 core 10 sq.mm PVCA Copper Cable |
| 44 | a) 3.5 core 120 sq.mm PVCA Aluminium Cable |
| 45 | Supplying including fitting fixing of followingA.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator].1200 mm Sweep orient make cat no. PEAK AIR or equivalent make |
| 46 | Supplying including fitting fixing sheet steel, phosphatised, powder painted single door surface mounting MCCB enclosure of the following rating MCCB fitted on the wall with grouting nuts and bolts as reqd. complete with making necessary connection as approved, specified and directed by the dept. for 160 A 4P MCCB |
| 47 | Supplyng and laying 25mm x 6 mm G.I strip at 0.50 metre below ground level for conductor earth electrode, includung connection/termination with G.I thimber etc. as reqd. |
| 48 | Supplying including installation commissioning of vermin and dust proff totally enclosed, phosphatised powder painted cubical ndoor type floor/wall mounting compartmentalize panel board of size 1.35 m x 1.5 m x 0.40 m made of 16 SWG/1.66 mm thick C.R sheet and 35 mm x 35 mm x 5 mm size angle having 4 no legs at the bottom. The panel board is to be erected in 1:3:6 PCC founation including brick soling/grouting etc. complete neatly wiring done with provision for one no of 250 A 4 pole MCCB or swtich fuse unit as incomer and provision for 8 nos DP or TPN out going as specified and directed by the deptt. confirming to IP 43 protection comprising of the following ecetrical items. Incoming and outgoing switch gear of reqd. rating will be measured and paid separately) |
| 49 | Providing and laiying Wall tiles of best quality |
| 50 | Providing and fixing W.C. (Eouropian Type) |
| 51 | Providing & fixing wash basin of best quality |
| 52 | PPG coloured sheet roofing including all necessary fitting |
| 53 | Water supply and sanitary pipe line system icluding waste disposal tank |
| 54 | Crushing unit(Cane Crusher of capacity at least 10q/h, planetary geartype, starter with electric panel) |
| 55 | Settling and Filtration unit(Settling tank, pump and series of filters consisting of wire mesh and vibro filters) |
| 56 | Clarification and boiling unit(boiling pan with base thickness 25mm, scum removal pan with bottom thickness 20mm and gutter pan withbottom thickness 12mm, shape circular/rectangle,material MS/SS s with 2-4 handles, , fire brick furnace with chimney) |
| 57 | Cooling, moulding and packaging unit(Cooling pan, six set of moulding frame with platform, band sealer, molten jaggery transfer pump, jaggery toolslike laddle, khurpa, scoop etc. ) |
| 58 | Laboratory Equipments(pH meter, brix meter, moisture meter, temperature meter etc. ) |
| 59 | Accessoriespump. Pipe, fittings etc. |
| 60 | Audio visual training devicesProjector, Laptop, camera, security system etc. |
