|
| 1 | Taking down Chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each complete all as specified and directed. |
| 2 | S&F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube and fixed with screws and rawl plugs complete all as specified and directed. |
| 3 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and directed. |
| 4 | Taking down Chowkhats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each including making good the wall surface complete all as specified and directed. |
| 5 | Taking down shutters of any descriptionexc 1 sqm & n. exc 2 sqmeach complete all as specified and directed. |
| 6 | S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as per specified and as directed. |
| 7 | S&F second class hard wood plain solid straight chowkats frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed. |
| 8 | S&F 2nd class HW35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 9 | M&L for 2nd class hard wood Kiln seasoned and chemically pressure treated glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed. |
| 10 | S&F aluminium anodized, barrel tower bolt of extruded section, 150 mm (ISI marked) complete all as specified and directed. |
| 11 | S&F butt hinges medium weight cold rolled mild steel 100 mm long (ISI marked) complete all as specified and directed. |
| 12 | S&F 150 mm long Aluminium handles, cast type (ISI marked) complete all as specified and directed. |
| 13 | S&F 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed. |
| 14 | S&F 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete fixed to steel frame /wooden frame including necessary welding, cutting, opening of wall for fixing bracket and making good complete all as specified and directed. |
| 15 | M&L plain cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in filling in hold fast and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed. |
| 16 | M&L mild steel work as hold fasts and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed. |
| 17 | M&L forming jambs etc to opening including cutting toothing and properly bonding into old work including facing and plastring to match existing work incement mortar 1:6 etc. complete all as specified and directed. |
| 18 | S&F in repair 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete fixed to steel frame /wooden frame including necessary welding, cutting, opening of wall for fixing bracket and making good complete all as specified and directed. |
| 19 | S&F in repair floor door stopper of aluminium alloy body and tongue, anodized with rubber washer at bottom fixed with screw to body and fixed to door shutter, over all length of cover plate shall be 150mm complete all as specified and directed. |
| 20 | Taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. and refixing in same opening, shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed. |
| 21 | S&F in repair aluminium anodized, barrel tower bolt of extruded section, 150 mm (ISI marked) complete all as specified and directed. |
| 22 | S&F in repair butt hinges medium weight cold rolled mild steel 100 mm long (ISI marked) complete all as specified and directed. |
| 23 | S&F in repair 150 mm long Aluminium handles, cast type (ISI marked) complete all as specified and directed. |
| 24 | S&F in repair 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed. |
| 25 | M&L for preparation ofnew or previously untreated surfaces of wood or wood based materials of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 26 | S&F powder coated (any colour and thickness of coating not less than 50 micron) aluminium window/ ventilator frame section 100 x 44 x 2 mm fixed with thrust bolts in wall by drilling (any number of leaf) comprising of following :-(a) Aluminium double shutter of glass and one shutter for wire mesh 44 x 44 x 2 mm top/bottom/side style.(b) Aluminium powder coated butt hinges 100 mm long 2 Nos in each shutter (c) Aluminium powder coated tower bolt 150 mm long 1/2 Nos in each shutter (d) Aluminium powder coated handle 150 mm long 1/2 Nos in each shutter(e) Tinted glass 4 mm thick(f) Aluminium anodised wire mesh of size 1.5 mm x 3 mm mesh, 20 Gauge thick (g) DG-104 10 mm thick Aluminium powder coated grill fixed with H section.NOTE:- On requirement sliding window with suitable fittings will be provided by the contractor without any extra cost to the Govt. |
| 27 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation board/Slabs/blankets of any thickness including cover fillets, complete all as specified and as directed. |
| 28 | S&F 12 mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work complete as specified and directed. |
| 29 | M&L for 4 mm thick Non asbestos fiber cement building board / E-boardfor ceilling incl aluminium powder coatedGI frame (snapgrid) of size 605 x 605 mm, main runner 38 x 24 mm sheet thickness 0.4 mm, cross tee 28 x 24 mm sheet thickness 0.3 mm and wall angle 24 x 24 x 0.3 mmfixed with hangers 6 mm dia GI (upto 1200 mm lenght) adjusting level type fixed to roof slab by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expension hold fastners 12.5 mm, 40 mm long of standard section as per manufacturers instructions complete all as specified and directed. |
| 30 | S&Faluminium anodised wire mesh of size 1.5 mm x 3 mm mesh, 20 Gauge thick in doors/window shutters complete all as specified and directed. |
| 31 | Dismantling wrought iron or mild steel work of any description complete all as specified and directed. |
| 32 | S&F mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 33 | Dismantling bamboo framing any type in garrage shutter or walls including attached whole bamboos or bamboo trellis and making good disturbed ground complete all as specified and directed. |
| 34 | S&F Mild Steel, plain, sheeting in stepped flashings, 1 mm thick, having tensile strength of 550 Mpa as in garrage/ roof covering / cladding to wall with grade of zinc coating 275 fixed with self tapping screws and fixed properly to angle iron frame/channel/ beam complete all as specified and directed. |
| 35 | S&F in repair Steel rolling shutters with 1.00 mm thick laths, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified & directed |
| 36 | M&L for preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed |
| 37 | S&F in repair 18 mm thickPrelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws as is shutters complete with Wooden beading of size 18 mm x 6 mm thick around open edges and varnishing / french polishing of beading complete as specified and directed. |
| 38 | S&F continuous ( piano) hinges, mild steel , bright finish or electrigalvanised width of flaps (when opened) 30 mm complete as specified and directed. |
| 39 | S&F 75 mm sizeHasp and staple , safety type, Aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws in repairs complete as specified and directed. |
| 40 | S & F 100 mm long Aluminium handles, cast type (ISI marked) complete as specified and directed. |
| 41 | S&F PVC door bottom weather strip door brush sweep seal fixed complete all as specified and directed. |
| 42 | M&L for preparation of old decorated plastered surfaces of walls including cornices, andapplying one coat of white wash on wall, facia, cornices etc. complete all as specified and directed. |
| 43 | All as per serialitem No 42 above on ceilings. |
| 44 | M&L for preparation of old decorated plastered surfaces of walls including cornices, andapplying one coat of cement base paint on wall, facia, cornices etc. complete all as specified and directed. |
| 45 | Dismantling of loose portion of concrete from ceiling and S&F of wiremesh of weight 2.5 Kg/Sqm and applying 25 mm average thickness in CM(1:4) mixed with and including liquid WPC (complast \"X\" as recommended by the manufacturer with guniting machine at a pressure not less than 5 kg/sqm finally rendering 10 mm thick plaster in CM (1:4) mixed with and including Liquid WPC (Complast \"X\" 421 from M/s Fosroc and nitobound AR from M/S Fosroc or equivalent as approved by GE ) in the proportion recommended by the manufacturer complete all as specified and directed. |
| 46 | M&L for preparation of old decorated plastered surfaces of ceiling and applying one coat of oil bound distemper complete all as specified and directed. |
| 47 | M&L for preparation of old decorated plastered surfaces of wall and applying one coat of oil bound distemper complete all as specified and directed. |
| 48 | M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 49 | M&L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed |
| 50 | M&L for complete removal of existance treatment of wall andapplying 3 mm thickwall care putty in two layers and applying two coat of oil bond distemper complete all as specified and directed. |
| 51 | M&L for preperation of old surface wall/ceilling by scrapping/ rubbing, applying, two coats of advanced anti-algal weather proof 100% acrylic smooth emulsion with silicon additives, over a coat of fibre reinforced elastomeric liquid water proofing membrane, including repair of patch work with CM 1:4 plaster upto 1 Sqm each area of any thickness,filling of cracks and holes with white cement complete all as specified and directed.Make- Asian paint damp proof + ultima suprema or equivalent in Berger/ Nerolac/ ICI India) |
| 52 | M&L for preperation of new surface wall/ceilling and applying two coats of advanced anti-algal weather proof 100% acrylic smooth emulsion with silicon additives, over a coat of fibre reinforced elastomeric liquid water proofing membrane complete all as specified and directed.Make- Asian paint damp proof + ultima suprema or equivalent in Berger/ Nerolac/ ICI India) |
| 53 | M&L for cleaning of surface with jet water to remove moss, fungus, dirt etc., opening of cracks upto 5 mm size and filling the same with PU sealent of Asian paint or equivalent in Sika, fosroc complete all as specified and directed. |
| 54 | M&L for applying one coat of primer under two coats of smartcare PU Aqua ofAsian paint or equivalent in Sika, fosroc and applying one coat of exterior emulsion paint to match the existing surface complete all as specified and directed.NOTE for item No. 53 and 54 :- Rate include cost of sacffolding upto 8 story building in area AGE B/R-II (Nofra-I and Nofra-II). |
| 55 | Taking down cement plaster on walls/ceiling of any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed. |
| 56 | Providing and applying 10 mm thick ready mix plaster on brick or concrete surface as per manufacturers specification finished even and smooth without using extra cement complete all as specified & directed.Make : Asian paint/ ACC/ JK Cement |
| 57 | Providing and applying 5 mm thick ready mix plaster on brick or concrete surface as per manufacturers specification finished even and smooth without using extra cement complete all as specified & directed.Make : Asian paint/ ACC/ JK Cement |
| 58 | M&L for applying one coat of alkali resistant primer on plasteredsurfaces over 3mm thick Birla white wall care putty and applying two coat of oil bound distemper including preparation of new surfaces complete all as specified and directed. |
| 59 | Providing and applying 15 mm thick ready mix plaster with water proofing compound on brick or concrete surface as per manufacturers specification finished even and smooth without using extra cement complete all as specified & directed.Make : Asian paint/ ACC/ JK Cement |
| 60 | M&L for preperation of wall surface and applying two coat of anti fungal paint to match existing surface of wall complete all as specified and directed. |
| 61 | M&L for applying 3 mm thickputty on ceilling surfaces and applying two coat of oil bound distemper including preparation the new surface complete all as specified and directed. |
| 62 | M&L for painting black colour circular base n. exc. 45 cm dia for writing building number with one coat of synthetic enamel paint complete all as specified and directed. |
| 63 | M&L for writing building No. or figure (Block, Roman, Italic or Indian) with two coats of synthetic enamel paintheight not exc. 30 cm and width n. exc. 2 cm over black base complete all as specified and directed. |
| 64 | M&L for preparation of old painted floor surfaces of any description over 10 cm width or girth by filling of cracks/holes with crack seal and applying two coats of floor paint Indigo or equivalent with spray machine complete all as specified and directed. |
