|
| 1 | Excavation and Earthwork |
| 2 | Surface dressing not exceeding 15cm deep in soft/loose soil complete all as specified and as directed |
| 3 | Excavation in trenchesnot exceeding 1.5m wide and not exceeding 1.5m in depth for foundations, manholes, etc. or for laying cables/pipes, erecting poles, etc. not exceeding 10sqm on plan and getting out in soft / loose soil complete all as specified and as directed |
| 4 | Returning, filling in, including, spreading, leveling, watering and well ramming in layers not exceeding 25cm deep as in any type of soil complete all as specified and as directed |
| 5 | Removing excavated materialsto a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point in any type of soil including spreading in low lying area and leveling complete all as specified and as directed |
| 6 | M&L for hard core of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, using broken stone or boulders complete all as specified and as directed |
| 7 | B/R works |
| 8 | M&L for plain cement concrete 1:4:8 (type D-2) using 40mm graded stone aggregates as in foundation filling, mass concrete, etc. complete all as specified and as directed |
| 9 | M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed |
| 10 | M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces complete all as specified and as directed |
| 11 | M&L for formwork to sides and soffits of floor or roof beam, beam haunching, girder, lintels, cantilever, shelves including supports, etc. for rough finished flat surfaces of concrete complete all as specified and as directed |
| 12 | M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 200mm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 50mm but n exceeding 100mm wide complete all as specified and as directed |
| 13 | M&L for formwork to soffits of suspended slabs, such as roof slab, floor slab, landings and similar works not exceeding 200mm thick for rough finished flat surfaces of concrete complete all as specified and as directed |
| 14 | M&L for mild steel TMT bars 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 15 | M&L for mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 16 | M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders securing with clips complete all as specified and as directed |
| 17 | M&L RCC M 25 design mix as in foundations including rafts, footings, foundation beams, plinth beams, column footings, under reamed piles, mass concrete, etc. complete all as specified and as directed |
| 18 | M&L RCC M 25 designmix as in columns, pillars, posts, etc complete all as specified and as directed |
| 19 | M&L RCC M 25 design mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed |
| 20 | M&L RCC M 25 design mix as in bands, beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed |
| 21 | Notes for serial item Nos. 53 to 56: (a) Mix design shall be conforming to relevant IS. Design mix shall be got designed from National Test House, SEMT Wing CME, Regional Research labs, IITs, National Institutes of Technology, Command Test Laboratory and Govt Engineering Collage and shall be got approved by the GE. Cost of obtaining design mix shall be included in the quoted rates (b) The Contractor shall use only one type brand of cement for entire structural/reinforced concrete work. In the event of contractor desiring use of any different brand of cement, fresh design mix shall be carried out and submitted for approval without any extra cost to the Govt.(c) Reinforcement steel will be measured separately under respective items herein |
| 22 | M&L for brickwork with sub-class \"B\" bricks, straight or curved on plan to any radius built in CM (1:6) complete all as specified and as directed |
| 23 | M&L for brickwork with sub-class \"B\" bricks, straight or curved on plan to any radius as in half brick thick walls built in CM (1:4) complete all as specified and as directed |
| 24 | M&L rendering 15mm thick, in cement mortar (1:4) on walls / concretesurfaces, etc. in two layers (10+5mm) finishing layer mixed with integral water proofing compound @3% by weight of cement, finished even and smooth without using extra cement complete all as specified and as directedNote: WPC will be measured and paid separately under respective item herein |
| 25 | M&L rendering 10mm thick, in cement mortar (1:6) on walls / concretesurfaces, etc. finished even and fair without using extra cement complete all as specified and as directed |
| 26 | M&L rendering 5mm thick, in cement mortar (1:3) on ceiling / soffits finished even and fair without using extra cement on roof slabs complete all as specified and as directed |
| 27 | Supply only integral water proofing compound all as specified |
| 28 | M&L for cleaning and applying one coat of cold bituminous primer (as approved by GE) @0.25litre/sqm over dried up surfaces of concrete / plastered surfaces conforming to IS 3384-1986 complete all as specified and as directed |
| 29 | Supply and laying APP based polymeric membrane 3mm thick (minimum), weighting not less than 3.5 kg/sqm reinforced with polyester non woven fabric (weighting not less than 160gms/sqm) applied over primed surfaces by torching application as per manufacturer\"s instructions with overlaps minium 100mm on the transverse directions and 75mm in longitudinal directions including one coat of aluminium paint @0.11kg/sqm complete all as specified and as directed |
| 30 | M&L for 75mm thick plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate as in floors, sub-bases, pavings, etc. surface finished even and fair complete all as specified and as directed |
| 31 | M&L for 75mm thick plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate as in floors, plinth protection, pavings, etc. including making spike rolling to surfaces or making impressions of expanded metal whilst the concrete is green laid in alternate bays of 3m length and joints between bays filled with 85/25 grade bitumen and sand mix @ 1:2 complete all as specified and as directed |
| 32 | M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in back filling of steel frame and holdfasts, etc. including necessary formwork complete all as specified and as directed |
| 33 | M&L for non-skid ceramic tiles, coloured, area of tile exceeding 0.18sqm but not exceeding 0.36sqm each, 7 to 8mm thick of superior quality as in floors, etc. jointed in neat cement slurry @3.00kg of cement per sqm and pointed in white cement mixed with colouring pigment to match shade of tiles, laid over and including 15mm thick screed bed in CM (1:6) (rate shall be included) complete all as specified and as directed |
| 34 | M&L for non-skid ceramic tiles, coloured, area of tile exceeding 0.11sqm but not exceeding 0.18sqm each, 7 to 8mm thick of superior quality as in vertical surfaces, dado, etc. jointed in neat cement slurry @3.00kg of cement per sqm and pointed in white cement mixed with colouring pigment to match shade of tiles, fixed over and including 10mm thick backing coat in CM (1:4) (rate shall be included) complete all as specified and as directed |
| 35 | S&F pressed steel frames of size 105x60mm, fabricated out of 1.25mm thick MS sheet for doors / windows, with one or more rebates including necessary fixing lugs, stainless steel hinges (100/50mm), lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of aldrop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs, etc. complete all as specified and as directed |
| 36 | S&F door closer hydraulically regulated, designation No. 1 universal type of aluminium (extruded section body) suitable for door shutters 700mm wide and of weight not less than 35kg and fixed complete all as specified and as directed |
| 37 | S&F anodized aluminium sections, powder coated (minimum 50micron) for door shutters with frame, three track sliding windows (2xglazed & 1xgauzed shutter), ventilator, partitions, etc including necessary jointing cleats, screws, etc. and fixed complete all as specified and as directed |
| 38 | M&L for 12mm thick pre-laminated particle board, exterior grade, prelaminated on both sides with decorative choice lamination and otherside balancing white lamination complete all as specified and as directed |
| 39 | S&F 4.8mm thick sheet glass ordinary quality and glazing with oil putting square exceeding 0.5sqm in each pane including hacking out old damaged glazing complete all as specified and as directed |
| 40 | S&F rubber beading for securing glass of suitable size complete all as specified and as directed |
| 41 | S&F 150mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and as directed |
| 42 | S&F 150mm extruded aluminum alloy handles, cast type, anodized complete all as specified and as directed |
| 43 | S&F 250mm aluminium anodised sliding door bolt with hasp and staple, bolt type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed |
| 44 | M&L for preparation of new / old plastered masonry / concrete wall internal surfaces including rubbing with sand paper to achieve even and smooth surface and applying 1mm thick (in two layers) wall care putty complete all as specified and as directed |
| 45 | M&L for preparation of new plastered or unplastered wall surfaces and applying two coats of oil bound distemper complete all as specified and as directed |
| 46 | M&L for preparation of new/old plastered surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungus resistant, dirt resistant, exterior paint (of approved tint, company depot tinted) with silicon additives @1.43litre/10sqm over a priming coat of exterior primer applied @0.90litre/10sqm complete all as specified and as directed |
| 47 | M&L for preparation of new masonry / concrete ceiling surfaces and applying three coats of white wash including all necessary staging, etc. as required complete all as specified and as directed |
| 48 | E/M works |
| 49 | M&L for point wiring with 1.5sqmm, two single core, FRLS PVC insulated, ISI marked, unsheathed cable 1100V grade, IS-694 marked, with multi-stranded copper conductor, drawn through and including non-metallic heavy duty PVC conduit not less than 20mm dia and accessories concealed in walls, ceiling etc. and including provision of 1.5sqmm copper wire, green colour as earth continuity conductor and connected to common earth dolly complete all as specified and as directed for the following: |
| 50 | One light / calling bell point controlled by one 6A one way switch |
| 51 | One switch socket outlet 3 pin 5A controlled by one switch on independent board |
| 52 | One switch socket outlet 3 pin 5A controlled by one switch on same board |
| 53 | S&F ceiling rose surface bakelite 65x50mm, ISI marked, with three terminals complete all as specified and as directed |
| 54 | S&F switch piano flush button type, single pole, ISI marked, one way 5A, 230V complete all as specified and as directed |
| 55 | S&F switch socket outlet, 5 pin, 5A flush type, universal, ISI marked, 230V complete all as specified and as directed |
| 56 | S&F wall surface mounted, compact LED box type, 4ft long, light fitting 1x20W all accessories prewired with 20W LED lamp and connecting with three core flexible copper conductor cable of suitable size from ceiling rose including taking down and disposing off old fitting complete all as specified and as directed |
| 57 | S&F building security light, LEDluminaire 25W high pressure die cast aluminium housing, heat, weather resistant, IP-66 protection class, with 25W LED lamp, driver, etc. with all accessories pre-wired, including bracket with 40mm bore GI tubing, light grade, cut and bent to shape required, 1.5m long, flat iron clamp made of FI 40x6mm, nuts, bolts, washers, etc. duly painted with two coats ofaluminium paint over a coat of red oxide zinc chrome primer including taking down and disposing off old fitting complete all as specfied and as directed |
| 58 | S&F sheet metal enclosures for 4 way MCB DB, 240V, SPN, double door, IP 43 protection class conforming to relevant IS, with 200A rated insulated aluminium bus bar, neutral link, DIN rail, blanking plates, etc. duly flushed in wall and making good the disturbed surfaces including taking down of old enclosure and disposing off complete all as specified and as directed |
| 59 | S&F MCB SP, 240V, 10 to 40A, 10kA, 50Hz, C curve complete all as specified and as directed |
| 60 | S&F MCB isolator SPN, 240V, 40A, 10kA, 50Hz, C curve complete all as specified and as directed |
| 61 | S&F 1100V grade heavy duty PVC insulated aluminium multistranded conductor cable of size 6 sqmm, served with inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hangers not more than 1m apart including 4mm suspension wire, two twin core cable flat or circular including taking down old unserviceable wire and disposing off complete all as specified and as directed of the following sizes: |
| 62 | Dismantling unserviceable ACSR conductor of any size, jumpers, etc. from overhead electric lines in any location / position and disposing off complete all as specified and as directed |
| 63 | Dismantling insulators of any size/type and sorting, stacking serviceable insulators and disposing off unserviceable complete all as specified and as directed |
| 64 | Dismantlingof stay assembly any make and any size from any height poles and disposing off unserviceable complete all as specified and as directed |
| 65 | M&L for dismantling old unserviceable cross arms, bracings, structural steel section including all T&P, sorting out and stacking serviceable materials for re-use and disposing off unserviceable complete all as specified and as directed |
| 66 | Supply,install, test and commissioning LT panel outdoor, floor mounted/pedestal type, cubical, self supported, CPRI approved make, front and rear openable, double door hinged type with locking arrangement and suitable ventilations on both sides IP 55 protection with dust and vermin proof etc, fabricated out of 3.15mm CRCA sheet duly powder coated, mounted/fixed on and including MS angle iron stand of 1 Mtr height( 50Cm above FFL and 50Cm below FFL), fabricated out of 50x50x5mm thick MS angles duly painted with two coats of black enamel synthetic paint over one coat of red oxide primer duly grouted in PCC 1:3:6 of foundation, control wiring copper stranded PVC insulated FRLS cables & inter connections of suitable size/capacity of aluminium strips for switch gear connection from main bus bar, earthbus strip of 25x3mm size for entire length of panel,suitable size of MS gland with gland plate and aluminium lugs/thumbles for all incoming and outgoing cables etc, complete all as specified and as directed by Engr-in -charge including and accomodating the followings: |
| 67 | Incoming(a) MCCB 4 pole320Amps 36Ka=01 Nos (b ) LED type three Phase indicator with controlling fuses for RYB =01 Set(c) Digital multi function meter (0-500V)(ratio100/5) with selector switch =01Nos(d) Aluminium bus bar size 400Amps TPx 250Amps for neutralOutgoing(a) MCCB 4 pole250Amps 36Ka-03 Nos (b) Digital time switch ML 2 contactor, TPN 32A=01Nos. |
| 68 | Supply,install, test and commissioning LT panel outdoor, floor mounted/pedestal type, cubical, self supported, CPRI approved make, front and rear openable, double door hinged type with locking arrangement and suitable ventilations on both sides IP 55 protection with dust and vermin proof etc, fabricated out of 3.15mm CRCA sheet duly powder coated, mounted/fixed on and including MS angle iron stand of 1 Mtr height( 50Cm above FFL and 50Cm below FFL), fabricated out of 50x50x5mm thick MS angles duly painted with two coats of black enamel synthetic paint over one coat of red oxide primer duly grouted in PCC 1:3:6 of foundation, control wiring copper stranded PVC insulated FRLS cables & inter connections of suitable size/capacity of aluminium strips for switch gear connection from main bus bar, earthbus strip of 25x3mm size for entire length of panel,suiytable size of MS gland with gland plate and aluminium lugs/thumbles for all incoming and outgoing cables etc, complete all as specified and as directed by Engr-in -charge including and accomodating the followings: |
| 69 | Incoming(a) MCCB 4 pole160Amps 36Ka=01 Nos(b ) LED type three Phase indicator with controlling fuses for RYB =01 Set(c) Digital multi function meter (0-500V)(ratio100/5) with selector switch =01Nos(d) Aluminium bus bar size 320Amps TPx 250Amps for neutralOutgoing(a) MCCB 4 pole63mps 25Ka-07 Nos (b) Digital time switch ML 2 contactor, TPN 32A=01Nos. |
| 70 | Supply,install, test and commissioning LT panel outdoor, floor mounted/pedestal type, cubical, self supported, CPRI approved make, front and rear openable, double door hinged type with locking arrangement and suitable ventilations on both sides IP 55 protection with dust and vermin proof etc, fabricated out of 3.15mm CRCA sheet duly powder coated, mounted/fixed on and including MS angle iron stand of 1 Mtr height( 50Cm above FFL and 50Cm below FFL), fabricated out of 50x50x5mm thick MS angles duly painted with two coats of black enamel synthetic paint over one coat of red oxide primer duly grouted in PCC 1:3:6 of foundation, control wiring copper stranded PVC insulated FRLS cables & inter connections of suitable size/capacity ofaluminium strips for switch gear connection from main bus bar, earthbus strip of 25x3mm size for entire length of panel,suitable size of MS gland with gland plate and aluminium lugs/thumbles for all incoming and outgoing cables etc, complete all as specified and as directed by Engr-in -charge including and accomodating the followings: |
| 71 | (a) MCCB TPN 250Amps 36Ka-01 Nos(Incoming)(b) Electrolyte aluminium bus bars PVC colour sleeved 400Amps capacity TP & 250 neutralmounted on hygroscopic insulator duly colour coded RYB and green sleeves |
| 72 | Supply,install, test and commissioning LT panel outdoor, floor mounted/pedestal type, cubical, self supported, CPRI approved make, front and rear openable, double door hinged type with locking arrangement and suitable ventilations on both sides IP 55 protection with dust and vermin proof etc, fabricated out of 3.15mm CRCA sheet duly powder coated, mounted/fixed on and including MS angle iron stand of 1 Mtr height( 50Cm above FFL and 50Cm below FFL), fabricated out of 50x50x5mm thick MS angles duly painted with two coats of black enamel synthetic paint over one coat of red oxide primer duly grouted in PCC 1:3:6 of foundation, control wiring copper stranded PVC insulated FRLS cables & inter connections of suitable size/capacity of copper strips for switch gear connection from main bus bar, earthbus strip of 25x3mm size for entire length of panel,suitable size of MS gland with gland plate and aluminium lugs/thumbles for all incoming and outgoing cables etc, complete all as specified and as directed by Engr-in -charge including and accomodating the followings: |
| 73 | (a) MCCB 4 pole,TPN 250Amps 36Ka-01 Nos(Incoming)(b)MCCB 4 pole,TP125Amps 25Ka-02 Nos(Outgoing)(c) MCCB 4 pole,TP 100Amps 25Ka-02 Nos(Outgoing)(d)MCCB 4 pole,TP 63Amps 25Ka-01 Nos(Outgoing)(e) LED lamps for phase indication R-Y-B- 01 set (set of three)(f) 3 phaseDigital multi function meter (0-500V)(ratio100/5) with selector switch =01Nos(g) Electrolyte aluminium bus bars PVC colour sleeved 400Amps capacity TP & 250 neutral mounted on hygroscopic insulator duly colour coded RYB and green sleeves |
| 74 | Notes for item No. 5 to 10:(a) The Contractor shall submit drawings from the approved OEM for approval of the GE through the Engineer-in-charge(b) The feeder pillar/panel shall include 2Nos. danger notice plates made of 1.6mm thick mild steel sheet, vitreous enamelled white, of size 250x200mm with letter, figures and conventional skull bones in signal red colour duly fixed with nuts, bolts and washers, etc. with voltage and danger indicated both in Hindi and English(c) The feeder shall include electrolyitc aluminium bus bars as stipulated PVC coloured sleeves mounted on hygroscopic insulators duly colour coded and earth bar in 40x5mm GI strip and complete wiring including flush mounting rated CTs of size 96x96mm(d) Excavation, earthwork in any type of soil, construction of PCC foundation for panel shall be deemed included in quoted rate. Foundation specifics shall be as per OEM of panel. The Contractor shall submit foundation desgn drawings to attain approal of he GE(e) Foundation bed shall be in PCC 1:3:6 type C2 using 40mm graded stone aggregates with a depth of 15cm below ground level and 1.5m above ground level with stare and slot openings for I/C and O/G cables(f) All MCB are of Ics=100% Icu |
| 75 | M&L forpreparation of surfaces viz. scrapping old paints, smoothening, etc. and painting to steel tubular poles of size 9 or 11metre height including GI pipe for street light, with two coats of synthetic enamel paint upto a height of 1.5m from ground, including painting of pole coping with synthetic enamel paint (black tint) and writing (font 1/2\"x3\") pole numbers with white synthetic enamel paint on circular base, marking of HT/LT, painting of balance portion of pole, cross arms, brackets with two coats of aluminum paint with all necessary staging, safety precautions, etc. as required complete all as specified all as directed. |
| 76 | S&F shock proof, rust proof pole mounting junction box, 100A rated, heavy duty of size 250x200x105mm with 32A 4 way heavy duty terminal block, for street lighting system with all accessories and including 1No. MCB SP 06A heavy duty connectors, 4 terminals, with necessary mounting arrangements to pole with clamp, nut bolts, cable gland with cable entry, suitable lugs, etc. incuding takng down old unserviceable junction box and disposing off complete all as specified and as directedNote: Sintex Industries Ltd / Supreme Industries / Naithani Plastic Moulding Works |
| 77 | Supply, laying, jointing, connecting and testing XLPE insulated PVC sheathed cable 1100V grade, screwed PVC bedded, armoured electric power cable, heavy duty multi-stranded aluminium conductor laid in trenches / fixed on walls/poles, passing through pipes, etc. including connecting up to DBs, etc. with required lugs, end terminal / cable glands including taking out/down old unserviceable cable and disposing off complete all as specified and as directed of the following sizes: Note: Excavation and earthwork will be measured and paid separately under respective item herein |
| 78 | 4 core 10 Sqmm |
| 79 | 4 core 16 Sqmm |
| 80 | 4 core 25 Sqmm |
| 81 | 3.5 core 70Sqmm |
| 82 | 3.5 core 95 Sqmm |
| 83 | 3.5 core 240 Sqmm |
| 84 | M&L for design, supply, connecting, testing and commissioning of Aerial Bunched Cable (ABC) [3 core 16sqmm + 1 core 25sqmm], ISI marked 1100V having XLPE insulated cable (three power core) with stranded compact circular aluminium conductors twisted over an insulated aluminium alloy messenger wire for use as overhead distribution feeders, with / without one street lighting core with stranded compacted circular aluminium conductor XLPE insulated suitable for use on 3-Phase AC system conforming to IS-14255/1985 (amended upto date)consisting of all accessories such as MS flat,LT insulators,GI earth spikes, GE earth wires, suspension clamp with pole bracket and steel strap, dead end/anchor clamp with pole bracket and steel strap, SMC service main distribution box 415V 250-140A with aluminiumbus bar for LT AB cable on requirement basis, insulation piercing connectors, cable end cap etc,as per site requirement, complete all as specified and as directed. |
| 85 | M&L for design, supply, connecting, testing and commissioning of Aerial Bunched Cable (ABC) [3 core 70sqmm + 1 core 50sqmm],ISI marked 1100V having XLPE insulated cable (three power core) with stranded compact circular aluminium conductors twisted over an insulated aluminium alloy messenger wire for use as overhead distribution feeders, with / without one street lighting core with stranded compacted circular aluminium conductor XLPE insulated suitable for use on 3-Phase AC system conforming to IS-14255/1985 (amended upto date) consisting of all accessories such as MS flat,LT insulators,GI earth spikes, GE earth wires, suspension clamp with pole bracket and steel strap, dead end/anchor clamp with pole bracket and steel strap, SMC service main distribution box 415V 250-140A with aluminium bus bar for LT AB cable on requirement basis, insulation piercing connectors, cable end cap etc,as per site requirement, complete all as specified and as directed |
| 86 | M&L for design, supply, connecting, testing and commissioning of Aerial Bunched Cable (ABC) [3 core 95sqmm + 1 core 70sqmm],ISI marked 1100V having XLPE insulated cable (three power core) with stranded compact circular aluminium conductors twisted over an insulated aluminium alloy messenger wire for use as overhead distribution feeders, with / without one street lighting core with stranded compacted circular aluminium conductor XLPE insulated suitable for use on 3-Phase AC system conforming to IS-14255/1985 (amended upto date) consisting of all accessories such as MS flat,LT insulators,GI earth spikes, GE earth wires, suspension clamp with pole bracket and steel strap, dead end/anchor clamp with pole bracket and steel strap, SMC service main distribution box 415V 250-140A with aluminium bus bar for LT AB cable on requirement basis, insulation piercing connectors, cable end cap etc,as per site requirement, complete all as specified and as directed |
| 87 | M&L for design, supply, connecting, testing and commissioning of Aerial Bunched Cable (ABC) [3 core 150sqmm + 1 core 120sqmm], ISI marked 1100V having XLPE insulated cable (three power core) with stranded compact circular aluminium conductors twisted over an insulated aluminium alloy messenger wire for use as overhead distribution feeders, with / without one street lighting core with stranded compacted circular aluminium conductor XLPE insulated suitable for use on 3-Phase AC system conforming to IS-14255/1985 (amended upto date)consisting of all accessories such as MS flat,LT insulators,GI earth spikes, GE earth wires, suspension lamp with pole bracket and steel strap, dead end/anchor clamp with pole bvracket and steel strap, SMC service main distribution box 415V 250-140A with copper bus bar for LT AB cable on requirement basis, insulation piercing connectors, cable end cap etc,as per site requirement, complete all as specified and as directed |
| 88 | Notes: (a) Rate quoted shall be inclusive of all accessories viz. MS flats, insulators, earth wires, suspension clamps, steel strap, pole brackets, connectors, caps, etc. as required complete(b) Tests shall be done as stipulated and reports are to be submitted alongwith claim of payments(c) Three run of XLPE insulated 1.1KV grade AB cable single core with one run of XLPE insulated aluminium messenger conductor shall be considered as 01Rm for measurement.(d) Successful commissioning of the entire system shall be the responsibility of the contractor. All items required for successful commissioning shall be deemed to be incliuded in the quoted rate, no extra shall be paid on this account. |
| 89 | Supply, erect in position and fixing steel tubular swaged poles with CI base plate (300x300mm and 6mm thick), finial taper plug, pole caps, bolts, nuts and screws type 410 SP-31, 9m long, conforming to IS: 2713, with detachable bracket arms including two coats of aluminium paint over shop coat of primer at any locations including shutting of power lines, etc. taking down of old / unserviceable poles, carting and disposing off complete all as specified and as directedNote: Excavation / earthwork and PCC coping etc. will be measured and paid separately under respective items herein |
| 90 | M&L for cable jointing kit for 1100V grade cable for straight through heat shrink type joint with jointing material and accessories suitable for 3.5/4 core 6 to 16mm², XLPE insulated armoured aluminium conductor cable including taking out and disposing off old joint complete all as specified and as directed |
| 91 | M&L for fine dry river sand cushioning by laying 8cm thick layer below the cable for making soft bed and 15cm above the cable and then punning down to its consolidated thickness of 18cm after the cable is laid all as specified in SSR Part-I complete all as specified and as directedNote: Only punned thickness of sand shall be considered for measurement purposes |
| 92 | Supply and laying burnt bricks of sub-class \"B\" of size 230x115x75mm laid in trenches for cable protection complete all as specified and as directed |
| 93 | M&L for cutting into / boring into existing road/PCC drain for takig out/laying of UG cable including all necessary earthwork nad making good to match with the existing surfaces with PCC 1:3:6 type C1 using 20mm graded stien aggregate, complete all as specified and as directed |
| 94 | Supplying, fixing / laying steel water tubing, 40mm bore, light grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for protection of electric clables including taking out and disposing off old damaged tubing complete all as specified and as directed |
| 95 | Supplying, fixing / laying steel water tubing, 80mm bore, light grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for protection of electric clables including taking out and disposing off old damaged tubing complete all as specified and as directed |
| 96 | S&F rigid non-mettalic PVC conduit inclusive of boxes with all tees, bend, elbows, etc. of size 20mm complete all as specified and as directed |
| 97 | S&F 3 core PVC insulated and PVC sheathed cable with stranded copper conductor of size 1.5sqmm, 1100V grade complete all as specified and as directed |
| 98 | M&L for earthing using GI earthing wire with galvanised steel earth plate electode 600x600x6mm thick buried directly in ground, earth pit not less than 2.25m deep below ground level connection to and including GI earth lead wire 4mm dia extended to 7.5m as earth lead by means of GI bolts, nuts, etc. with provision of charcoal and salt all as per electrical plate No. 3 of SSR Part-I including water arrangement with GI pipe 20mm dia (medium grade), earth lead protection pipe 15mm light grade with bends, elbow, etc. from earth plate to test point, excavation and earthwork in any type of soil, returning, filling, ramming and removing of soil to distance not exceeding 50m, make good to match with existing surface making PCC pit (earth chamber) having internal size 300x300x300mm and outer size 600x 600x600mm with RCC reinforced cover 50mm thick and testing on completion including making test points on wall as per SSR specifications, taking down and disposing off old earthing complete all as specified and as directed |
| 99 | Notes for serial item No. 98: (i) The cost of GI earth continuity wire / strip with GI pipe 20mm medium grade upto 7.5m is deemed to be included(ii) The earth chamber to be constructed 0.5m from edge of earth pit with necessary watering arrangement. The cost for the same is deemed to be included in above item(iii) Earthing shall produce desired earth resistance values as directed by the Engineer-in-charge |
