Tender For Dental College Se Kazipura Hote Hue Agwanpur Railway Crossing Ke Paar Kanth Side Kanth Road Tak - Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 including all labour, material, labour cess, T&P etc complete but excluding GST. 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam (G-3) specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory rollerin stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. including all labour, material, labour cess, T&P etc complete but excluding GST. 3 Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. including all labour, material, labour cess, T&P etc complete but excluding GST. 4 Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregatesusing Viscocity grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable hot mix plant of appropriate capacity not less than 200 tonnes/hour, laying and rolling with a smooth wheeled roller, finished to required level and grades. including all labour, material, labour cess, T&P etc complete but excluding GST. 5 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A seal coats. including all labour, material, labour cess, T&P etc complete but excluding GST. 6 Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 310 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing.including all labour, material, labour cess, T&P etc complete but excluding GST. 7 Excavation in foundation in ordinary soil (loam clay and sand) including lift upto 1.50 M and lead upto 30M and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the side of foundation, including cost of material, labour,Royalty, labour cess, T&P etc and other taxes but excluding GST. 8 Cement Concrete with 4 cm gauge with Stone Ballast coarse sand & Cement in proportion 8:4:1 in foundation proper completion of the work including cost of material, labour,Royalty, labour cess, T&P etc and other taxesbut excluding GST S.I. No. 281 9 R.C.C. Work with cement approved coarse sand and 2cm. gauge approved stone grit in proportion of 1:2:4 in lintels of doors, windows and sunshades excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I Binding wire and including necessary centering and shuttering etc. and supply of all meterials, labour and T&P etc. required for proper completion of work. Binding wire to be supplied by the contractor free of cost. Including making of drip coarse including all labour, material, labour cess, T&P etc complete but excluding GST. 10 Mild steel or TMT Bars(Fe-500D grade or higher) orHYSD Bars or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) brought to required shape as necessary including bending for proper completion of the work and including supply of all steel. but excluding GST S.I.No. 504.
