|
| 1 | Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etc andremoval of entire debris as ordered outside MD land complete all as directed. |
| 2 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thick above or below ground level and removalof entire debris as ordered outside MD land complete all as directed. |
| 3 | Demolition of brickwork , block masonryor stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed. |
| 4 | Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stackingserviceable tiles at site andremoval of entire debris as ordered outside MD land complete all as directed. |
| 5 | Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed. |
| 6 | All as per item 5here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each |
| 7 | Taking down shutter of any description exc 1Sqm butnotexc 2 Sqmeachand stacking at site where directed. |
| 8 | Taking down shutter of any description area exceeding 1 Sqm but not exceeding 2 Sqm each and refixing in the same opening after cutting , easing and adjustmentas withold ll types ofbuilders hardware complete all asdirected. |
| 9 | M & L for Hard core of broken hard stone or boulders of guage not exceeding 63 mm , deposited spread as subbase to inter locking tilesin layers n.exc 15cm thick , watered & well rammedto true surface complete all as specified and directed. |
| 10 | M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified. |
| 11 | M&L for cutting holes in stone / brick walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as required, exc half brick & not exc one brick (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall). |
| 12 | S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications completeall as directed. |
| 13 | S&F Second class hard wood factory made kiln - seasoned, plain, solid, straight chowkats and frames , wrought, framed, rebated on the solid, rounded or chamfered , put togetherwith glue, pinned at joints and fixed in position complete all as directed. |
| 14 | S &F35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats. |
| 15 | S&F 30 mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack allas specified. |
| 16 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement. |
| 17 | S&F in repairs Pre-laminated particle board , Exterior grade 18/19 mm thick (ISI Marked) , pre-laminated both side withdecorative choice lamination including 3 mm thick teak wooden beading alround as orderedcomplete all as specified. |
| 18 | S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed. |
| 19 | S&F100 mm size butt hinges, medium weight coldrolled mild steel and fixed . |
| 20 | S&F 150 mm size aluminium alloy handles (ISI Marked) fabricated type anodisedand fixed. |
| 21 | S&F300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. |
| 22 | S&F in repairmild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate, welded to steel frame, including making suitable cut out in wall and making good in CM 1:4 complete all as specified & directed |
| 23 | M&L for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty & fixed as directed |
| 24 | S&F in repair 25mm dia aluminium anodised decorative type curtain rods. fixed with CP steel screws complete all as specified and as directed. |
| 25 | S&F in repair decorative type curtain rod brackets. |
| 26 | S&F in repair brass chromium plated tubular towel rail, 20mm dia, \"D\" type, 60cm long be-tween flanges complete all as directed including taking down old towel rail. |
| 27 | S&F anodized aluminium frame for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed. |
| 28 | S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed |
| 29 | S&F Powder coated aluminium sliding window (three way) frame & shutter with glazed shutter and without miremesh shutter /skeleton section with & including the following:-(i) Aluminium frame section 116x36.50x1.80mm.(ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick.(iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars complete all as specified.(iv) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(v) 5mm thick glass orinary quality and fixed with rubber gasket for with glazed shutter etc.(vi) Stainless steelwire mesh 0.36mm nominal dia avg aperature 1.14mm and fixed with rubber gasket for without glazed shutter etc.(vii) Aluminium disc /bow hanle and locking system complete |
| 30 | S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with & include the following:-(i) Aluminium frame section 45x25x1.80mm.(ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(v) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc. |
| 31 | S&F stainlesssteel wire cloth0.24 mm nominal dia of wire and averagewidth of aperature 1.40mm and fixed with stainless steel wirestaples including supply & fix secondclass hard wooden fillet, wrought , cross sectional area exceeding 3 Sqcm but n.exc 6 Sq cm fixed with nails complete all as directed. |
| 32 | S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Grade E-165 (Fe 290) and fixed in position. |
| 33 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets& S & F4 mm thick of size 600mm x 600mm HSPC (High pressure steam cured) pre-primetered self embossed, textured designer board E-Board Classic( White colour) to be fixed and including GI basedframe work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screw at 450mm centre to centre/ intermediate channel 09mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with & incl ceiling section(n.exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm fixed to intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre suspended with 6 mm dia GI barhangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purline from the roof with alignment clip including providing provision for light fixtures of any size complete all as specified. |
| 34 | M&L for 25 mm thick plain cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floor and finished the surface suitable to receivefloor tilescomplete all as directed. |
| 35 | M & L for 75 mm thick plain cement concrete 1:4:8 type D2 using40mm graded crushedstone aggregate as insub base offloor/ foot path etc and finished the surface complete all as directed. |
| 36 | M & L for 75 mm thick plain cement conctere 1: 3 : 6type C2 using 40 mm graded crushedstone aggregateas in plinth protection finished the surface fairand even complete all as directed. |
| 37 | M & L non-skid coloured joint freeceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified. |
| 38 | M & L non-skid coloured joint freeceramic tiles matt finish7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all directed and specified. |
| 39 | All same as per item No 38 here-in-abovebut tiles of size exceeding 0.11 Sqm butnot exceeding 0.18 Sqm as in skirting but tiles laid over and including 10 mm thick screed bed in cement mortar 1:4 -do- |
| 40 | S&F vitrified ceramic tiles 10mmmm thick (square/rectangular) area of each tile exceeding0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to matchwith tiles laid over and including 20 mm thick screed bed in cement mortar 1:6 complete all directed and specified. |
| 41 | All same as per item No 40 here-in-abovebut tiles of size exceeding 0.36 Sqm as in skirting but tiles laid over and including 10 mm thick screed bed in cement mortar 1:4 -do- |
| 42 | M&L glazed ceramic coloured tiles of size 350mm x 250mmx 7mm / 450mmx350mmx7mm thick, on verticals surfaces, set and jointed inneat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to matchcompleteall directed.(Note for item Nos 37 to 42 : i) Quoted rateis deemed to be inclusive of cement screed. ii) Colour of tiles shall be got appproved before incorporation in the work) |
| 43 | M&L for factory made chequered cement concrete tiles, 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & no pigment, over & including 20mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed . (Note; Quotedrateisdeemedtobe inclusiveofcementscreed). |
| 44 | M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit laid over andincluding15 mm thick screed bedding in cement mortar 1 : 4includingRounding to edges complete. |
| 45 | All same as per item No 44here - in - above but as in dado & skirting with10 mm thick 1 : 3 cement mortar screed - do -(Note for item No 44 & 45 : i) Quoted rateis deemed to be inclusive of cement screed.) |
| 46 | M&L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified. |
| 47 | M&L for rendering 15 mm thick in CM 1:4 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified. |
| 48 | M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of alkaline resistant primer complete all as directecd. |
| 49 | M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified. |
| 50 | Hacking out old broken glass (any thickness) and size from wooden frame glazed with putty or fixed with wooden beads and removal of debris to a distance n.exc 50 mtr and depositing where directed. |
| 51 | S & F sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads in square exc. 0.5 sqm in each pane complete all as directed. |
| 52 | Fixing only 5.5 mm thick sheetglass ordinaryquality cut toany size in square / rectangular in each pane complete all as directed. |
| 53 | S&F sheet glass 4mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each panecompleteall as directed. |
| 54 | M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed. |
| 55 | Taking down old rusted / wornout 15 mm bore GI tubing after necessary disconnection & S&F new 15 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed. |
| 56 | Taking down old rusted / wornout 20 mm bore GI tubing after necessary disconnection & S&F new 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed. |
| 57 | Taking down bib tap, pillar cock, stop/angle cock, & shower rose etc for carrying out repair/ refixing the same in old position after cleaning, replacing washer, spindle and adjusting screws etc complete all as directed. |
| 58 | S&F in repairs 15mm Bib taps chromium plated fancy type cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for union.Make:Prayag 8306 or equivalent |
| 59 | S&F in repairs 15 mm bore stop valve / angle valve , cast copper alloy, chromium plated fancy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions. |
| 60 | S&F in repairs 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated,screwed down high pressure, with or without lettered‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes. |
| 61 | S&F in repairs 2 in 1 CP 15mm Bib cock doublehandlewithflange cast copperalloy , screwed for iron pipe or for union. |
| 62 | S&F in repairs brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore withprovn of over headshower & cock all as specified and as directed |
| 63 | S&F in repairsShower rose with brass chromium plated shower rose with or without swivel joints, 100mm size including fixing to steel pipe or union. Make: Cera Cat No-F7020304 or Equivalent. |
| 64 | S&F in repair32/40mm bore Low density polyyethylene (LDPE) pipes plain /corrugated of pressure rating 6 kgf/Sqcm withconnectingbracket fixedtowaste coupling forbasin/ sinkscompleteall sdirected. |
| 65 | S & F in repair PVC flush handle including connecting rod & shiphon washer suitable for 10 litre capacity PVC flushing cistern complete all as directed. |
| 66 | S&F in repairs 15mm bore bib tap standard of PTMT any colour, high pressure, screwed for iron pipe and fixed (minimum weight 90 gms) complete all as specified and as directed. |
| 67 | S&Fin repairs15mm bore Pillar tap of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 110gms). |
| 68 | S & F in repairs PVC connection pipe suitble for 15 mm bore ofpipewith PTMT nuts, 600mm long complete all as specified |
| 69 | S & F in repairs chromium plated health faucet(ABS) with 1 metre long flexible pipe suitable for 15mm bore pipe complete all as specified and directed. |
| 70 | S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wallin repars complete all as directed. |
| 71 | S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wallin repars complete all as directed. |
| 72 | S & F 110 mm bore, PVC (SWR) bends of any radius complete all as specified and directed. |
| 73 | S & F 75 mm bore, PVC (SWR) bends of any radius complete all as specified and directed. |
| 74 | S&F in repair 110 mm bore PVC (SWR) junction double (double ‘T’), equal or unequal with oval access door |
| 75 | S&F in repair 75 mm bore PVC (SWR) junction double (double ‘T’), equal or unequal with oval access door |
| 76 | S&F in repair 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed. |
| 77 | S&F in repairBall brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed |
| 78 | All same as per itemNo 77 here-in-above but 25mm bore or brass ferrule -do- |
| 79 | S&F 550 mm X 400 mm size white flat backvitreous china wash hand basin including chromium plated pillar tap (Make: CERA Cat No. S1053101/S1053102 6502) cap stain head suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitablewashers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected. |
| 80 | S&F in repairs 600mm x 450mm looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick AC building board or commercial plywood including aluminium framing and fixed to PVC rawl plugs with chromium plated brass screws and cup washers complete all as specified. |
| 81 | S&F in repairs vitreous china bowl type urinal flat back, size of 465 x 355 x 265mm (minimum) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified |
| 82 | S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etcincluding provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified. |
| 83 | S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low levelPVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag |
| 84 | S&FPVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including32 mm dia PVC flush pipeconnected to water closet with inlet, ball valve, float and handle complete all as specified |
| 85 | Disconnecting existing tanks, setting aside ( for lowering if required) for repairs, cleaning,etc and hoisting if requiredreconnecting and refixing in positing including cleaning and removing all scale and dirt,etc from tanks and from mouths of circulating pipes. ( Capacity exc 500 but n exc 1000ltrs) |
| 86 | All same as per itemNo 85 here-in-above but tank ofsize exc 250 lts but not exc 500 lts -do- |
| 87 | Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site andS&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical verticalwith close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 20 mm bore of pipe with polythene float, fixture hoisted and fixed in position where orderedand making necessary connection and testing complete all as directed. |
| 88 | Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site andS&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical verticalwith close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, fixture hoisted and fixed in position where orderedand making necessary connection and testing complete all as directed. |
