|
| 1 | Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge |
| 2 | Dismantling old plaster / skirting carefully , raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100 m lead |
| 3 | Dismantling Aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable materials within 100 m lead as directed by the Engineer-in-charge |
| 4 | Dismantling roofing including ridges, valleys and gutter etc and stacking the material within 50 m lead |
| 5 | G.S Sheet / FRP Sheet / AC Sheet |
| 6 | Providing Asbestos cement 6 mm thick corrugated sheets (as per IS:14871) roofing up to any pitch and fixing with G.I J or L hooks, bolts and nuts 8 mm dia G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete excluding the cost of purlins, rafters and trusses corrugated sheets and including cutting to size and shape wherever requiredcomplete as directed by the Engineer-in-charge |
| 7 | Asbestos sheet roofing without ridges |
| 8 | Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels |
| 9 | Providing and constructing brick work in Cement mortar using standard bricks of approved class/ quality, make or brand in foundation and plinth including curing, raking out joints, simultaneous pointing below plinth level if specified, complete as per drawings, specifications and as directed by the Engineer-in-charge |
| 10 | Brick work in C.M 1:4 using crushed sand. |
| 11 | Providing 15 mm thick plastering using Ready mix internal plastering compound of approved make for internal faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning, scaffolding complete all as per specifications and as directed at site by the Engineer-in-charge |
| 12 | Providing and applying white cement based wall putty of approved make over concrete or Plastered surface up to 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer-in-charge |
| 13 | Providing and Painting with 1st quality acrylic washable distemper (ready made) with Two coats on new work of approved make and manufacturer and of required shade and colour, including scaffolding, preparation of the surfaces ,etc., including a coat of approved cement primer.as per manufacturer\"s specifications and as directed by the Engineer-in-charge. |
| 14 | Providing and fixing Glazed VITRIFIED floor tiles of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge. |
| 15 | Using Tiles of size 600 X 600 mm |
| 16 | Providing and fixing panelled teak wood door shutters (35 mm thick frames and 25 mm thick shutters) using second class teak wood using styles & middle rails 100 mm x 35 mm, bottom rail 200 mm x 35 mm, top rail & lock rails 150 X 35 mm and panelling with 25 mm thick best quality teak wood planks including fixing in existing door frame including ISI marked 100 mm stainless hinges with SS screws complete all as per specifications and as directed. |
| 17 | Providing wood work in frames of doors, windows, clear story openings and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing, making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the surface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge |
| 18 | Second class teak wood |
| 19 | Providing and fixing brass mortise latch and lock of approved make with 6 levers and a pair of lever Brass handles with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications. |
| 20 | Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer of approved make with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts complete as per specifications and as directed by the Engineer-in-charge. |
| 21 | Providing and fixing minimum 17 mm thick gang saw cut mirror polished granite (premoulded and prepolished) machine cut ZEBRA BLACK colour granite for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edge to give high gloss finish etc. complete as directed by the Engineer-in-chargeat all levels |
| 22 | Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealant etc. (fittings glazing and panelling shall be paid for separately) |
| 23 | Anodised Aluminium sections (Minimum anodizing thickness of 15 micron) |
| 24 | Extra for colour anodizing |
| 25 | Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of theEngineer-in-charge (Cost of snap beading shall be paid in basic item) |
| 26 | With clear float glass panes of 6.00 mm thickness |
| 27 | Providing and fixing 9 mm thick pre-laminated particle board flat pressed 3 layer or graded wood particle board conforming to IS 12823 Grade-I, Type - II in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge Prelaminated particle board with decorative lamination on both sides |
| 28 | Providing and fixing Aluminium Grill 10 mm thick \"DECO GRILLE\" make Model No. DG- 102 in natural Silver anodising of min 15 Microns with a opening size of 80 mm x 66 mm and Minimum weight of 3.13 Kg/ Sq.M including providing and fixing Suitable \"F\" / \"H\" section outer frame and mullion fixing with screws complete all as per specifications and as directed at site by the Engineer-in-Charge .Aluminium alloy shall be of 6063-T6 with Yield strength of minimum 6.5 kg/sq.mm. |
| 29 | Providingarranging in position and fixing L Shaped Work station consisting of Main tablewith side table of dimensions as mentioned belowbiult in 20 mm thk. Marine plywood including side unit, pencil tray, pullout tray, footrest. All drawers to be in plywood with 20 mm in front & 12 mm thk. in rear & sides , bottom in 6 mm thk. Plywood Internal surfaces to be laminate . Table tops, side table unit fronts & sides to be finished in 20 mm thick plywood as per drawings.The front modesty panel etc. shall be finished as per drawings & instructions of the EIC.All beadings, mouldings & exposed woodwork to be in teak woodor PVC Edge bending (As per requirement of EIC)Foot rest shall be made out of 20 mm plywood & shall be finished with approved shade and colour laminate. All TW molding and bottom of tables shall be finish in 3 coats of French polish.All the tables shall have keyboard drawers to accommodate key boards & mouse wherever necessary as per drawing.Rate include of all hardware, sliding door casters, drawers with multilock (Godrejmake) fitted on drawer channels,s.s. handles,etc .All exposed woodwork to be finished with 3 coats of melamine polishall internal surfacesfinished with 0.8 mm thick laminate the exposed surfaces shall be finished with 1.5 mm thick Laminate of approved shade & colour.etc. complete as per drawings ,specifications and directions of engineer in charge Technical Specification - Metal Tray - Tray is made of 0.9 mm thick MS Sheet CRCA. (Size: 482(W) x 270(D) x 18(H) MM). Single Extension Ball Slide assembly - 350 mm (Long) x 11.8 mm (Thk) Single extension (Stroke: 230 mm) Ball-slide Made of combination of 1.2/1.5 mm thk roll-formed CRCA Steel sheet. Mouse Tray - Optional retrofit mouse tray is provided which could be fitted at right hand or left hand as per user requirement. Mouse tray (Size 210 x 210) is made of 0.9 mm thick MS CRCA Sheet. Technical Specification- L : 225-330mm (adjustment), W : 225mm, H : 330mm (MS 14BG, Powder Coated 50-60 MICRON DFT) |
| 30 | Workstation having main table 1500 mm x 450 mm x 750 mm (contains 3 drawer storage unit at main) and side table of 1100mmx 600 mm x 750 mm (Side table contains 2 shelves with front shutter and CPU place) |
| 31 | Providing and supplying on site medium back 360degrees revolvingtype and tilting chairswith ergonomically contoured backrest ,upholstered withfoamlaminatedmeshfabric of approved colour , five legged high quality nylon base and PU twin wheelcasters having synchro mechanism with 4 position locking , seat slide mechanism with 3 D armrest . TheChairs shall be of High Resillence (H.R.) foam for optimum seating comfort with approved fabric colouretc. complete as per drawings , specificationsand directions of engineer in charge . Godrej Interio or equivalent Make Net Gallop High Performance Chair |
| 32 | Mid back |
| 33 | Providingarranging in position and fixing Low level wooden partition with aluminium framing made up of two numbers of 12mm Marine ply wood on both side & shall be finished with 1.5mm thick laminate of approved shade and colour , all beadings, mouldings & exposed woodwork to be in teak wood complete all as per |
| 34 | Providing and fixing of Hollow metal Two Hour fire rated doors (of approved ISO 9001-2000 certified Manufacturer) as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with the following specifications. The recommended fire doors shall be tested at CBRI or ARAI for maximum rating of 2 hours with vision panel. Test certificates shall be furnished for vision panels as part of the fire door assembly. Independent glass test certificates shall not be accepted. The manufacturer\"s test certificate shall cover all doors supplied shall be within the tested specimen. Deviation in specification and sheet thickness other than what is mentioned in the test certificates shall not be allowed. Proper label confirming the type of door and the hourly rating shall be mandatory. |
| 35 | Single leaved Door |
