Providing Furniture For Court Building At Palghar In Talukapalghar District-Palghar.-1 Partition :- Providing and fixing low height partitions at required location having minimum 65mm thick made by using 50x50mm (finished size) Centrally Providence Teak Wood (CPTW) section framing at 600 mm center to center, covered with 6 mm marine ply requisite manufacture generally confirming to I.S. 303/I.S. 710/- 1980 on both sides. The partition shall be finished with formica laminate sheet finished lamanation pattern with or without grooves externally with necessary lipping (Bourmah Teak wood) moulding antitermite treatment to all plywood and wood work including all leads and lifts etc. complete as per Architects Drawing and instruction of the Engineer in- charge. 2 Low Height Storage - Providing & fixing on site 40 cm Deep Low Height Storage Unit at require location less than 1.35 meter height by using 19mm marine ply of requisite manufacture generally confirming to I.S. 303/IS. 710-1980 for frame, internal verticals, horizontal divisions, openable shutters, 6mm thick marine ply back, with necessary locks, handles, hardware, lipping (BTC), moulding etc. The total shall be finished with formica laminate sheet finished lamination pattern with grooves externally and two coats of french polish with anti-termite treatemtn to plywood & wood work including all leads & lifts etc. complete, as per Architects Drawing and instruction of Engineer in Charge. 3 Storage Full Height : Providing and fixing 53cm deep Cupboard type Storage Unit made out of 19mm thick marine plywood of requisite manufacture generally confirming to I.S. 710-1980 frames, internal verticals horizontal divisions, shutters and 6mm 12mm thick marine plywood for drawers with locks,handles, hardware, lipping & beading patti (BTC) etc. The shall be finished with veneer in approved pattern with grooves etc. and two coats french polish and melamine polish for all BTC moulding & lipping patties with antitermite treatment to plywood & wood work with years guarantee on requisite stamp paper including all leads & lifts etc.complete as per drawing and instruction of Engineerin-charge etc. complete 4 Supplying glass table top 8 mm thick in required size and shape including finishing the all side edges machnically smoothly etc. complete. as director Engineer in charge. 5 Supplying Table Cloth ( Sarj ) (Material supplied should be standard company) as director Engineer in charge. 6 Providing & fixing in position table for the Clerical Staff having overall size of 120x60x76 cm height made out of 19mm thick Marine Ply of the requisite manufacture generally confirming I.S.303/I.S.710-1980 top, vertical side & 6mm marine plywood requisite manufacture generally confirming to sides and 6mm marine ply bottom with necessary sliders one open shelf of 19mm thick marine ply with necessary lipping on external sides and foot rest out of 40x75 mm (finished dimension) CPTW etc. as per drawing and instructions. the external side and top shall be finished with 1mm thick laminate matt/suede/fine line finished lamination pattern with grooves all internal surfaces on table and drawer shall be internally finished with two coats of french polish with antitermite treatment. director Engineer in charge. 7 8 Staff Revolving Chair : Providing Visitor Chairs having a medium back with head rest, with a synchronized tilting mechanism with Multiple locking systems, ABS for seat, with swivel & depth. The chair shall have adjustable arm pad & option of PVC padding.The seat shall have a gas lift for height adjustment and the chair shall have a Nylon base with castors. as director Engineer in charge. 9 Visitors Chairs/Fix Chair : The seat and back are made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE:47.5 cm. (W) x 58.0cm. (H)SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) POLYURETHANE FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression.3) ARMRESTS: The onepiece armrests are injection moulded from black Copolymer Polypropylene as per order. (Material supplied should be standard company) as director Engineer in charge. 10 Double sided name plate made out of 6mm thick sun board size of 15 x 8 pasting vinyl yellow golden letter patch on both side on black patch etc. complete. 11 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. 12 Providing and laying in situ cement concrete of 1:4:8 proportion with trap/ granite/ quartzite/ gneiss metal in foundation including necessary form work, compacting and curing etc. complete. (with reversible drum type mixer with SCADA with fine agreegates of required specifications (Natural sand / VSI sand finely washed etc ) 13 Providing and laying chequered tiles of approved quality of size 30 cm x 30 cm, confirming to corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. 14 Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Numbers 15 Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 16 Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 17 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 18 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete 19 Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. 20 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. 21 Providing and applying plastic emulsion paint of approved quality, colour and shade to old surface in three coats including scaffolding, preparing the surface. (excluding primer coat) etc. complete. 22 Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: For Item One Number 15 to 18 prior approval of Superintending Engineer will be necessary 23 Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use) 24 Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top, 40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding finishing, buffing to stainless steel pipe etc. complete 27 Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/One Running Metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box 28 Providing and fixing 30mm thick PVC FLUSH L DOOR SHUTTER consisting of panel of hollow PVC profile of 20 mm thickness consisting frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mminserted inside the hollow section of stiles rails top ?and bottom rails and two 19x 19 mm MS tubes inserted horizontally inside the hollow profile section using 4/5 mm sheet using screws hollow profile shall be lipped with 10 mm (5mm x2) thick x 20 mm width on stiles and rails using solvent cement. The inner panel shall be laminated with 5mm thick termite proof waterproof plain /prelam PVC sheet using solvent cement on the both sides of the panel including stainless steel fixtures and fastening etc. Complete as per direction of Engineer incharge, manufacturers specification and drawing. 29 Providing 25 mm to 30 mm thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. b) Both side polish 30 Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish 31 Providing and fixing Shutter to wall Cupboard consisting of Teak Wood styles and Rails 25 mm thick and 75 mm wide with panel insert of 12 mm thick particle Board with one approved coloured Laminated Face on one side 1.5 mm thick, bonded with Phenol Formaldehyde Synthetic Resin including Lipping Beading. Iron oxidised fixtures and fastening and oil primer coat etc. complete. (Excluding cupboard frame). 32 Other Minerals HB Metal ,Murum 37 Test Report Density and moisture content PLYWOOD Determination of Resistance to dry heat,Determination of Moisture Content,Determination of Density,Thickness of Plywood. Tiles Flexural test Water Absorption Resistance to Wear Flooring of Natural Stone BASIC TEST OF CEMENT. Standard Consistancy, Fineness, Specific Gravity, Setting Time ( Initial & Final ), Compressive Strength, Soundness. Structural steel Standard Consistancy, Fineness, Specific Gravity, Setting Time ( Initial & Final ), Compressive Strength, Soundness.
