|
| 1 | Repair works of Wash rooms and lorry loading chute floor area at Bagging plant of FACT CD ,Ambalamedu, Kochi. |
| 2 | Chipping & removing ceramic floor tiles/dadoing including the mortar bed/adhesive and paint layers if any on the walls in the toilet rooms and other areas if any very carefully without damaging the remaining portions and water supply items and removing the debris to places pointed out by the department. |
| 3 | Dismantling and clearing away any thickness of rubble, brick, laterite in CM including disposal of debris as per directions within a distance of 150 m. |
| 4 | Dismantling CC/RCC works including separately removing & stacking available reinforcement & clearing away the debris as per directions within a distance of 150 m. |
| 5 | Dismantling existing old sanittary fittings like wash basin, EWC,Urinal etc and removing all internal water lines and waste lines carefully without damaging the building as instructed at site from 2 toilet blocks. |
| 6 | Dismantling and removing doors with or without ventilators including removal of shutters, hinges,holdfast and all other fittings and stacking materials as per deptl.instructions |
| 7 | Cement Concretework in 1:1½:3 nominal mix using 20 mm and downgrade hard granite broken stone including all charges for cement ,mixing concrete, laying, consolidating, curing etc.complete but excluding cost of form work & reinforcement works.For foundation footings, bottom & sides of trenches, equipment foundations, plinth beams, lintels, slabs, columns & beams etc.up to 5 m from ground level. |
| 8 | Providing formwork to RCC works with necessary wooden planks, joists,runners, posts etc.including removal after completion of works-For columns/Foundation footings. |
| 9 | Labour, Material and supervision charges for cleaning the surface using wire brush followed by water in order to remove all deleterious matters including old worn out tar felt and applying water based primer / bituminous primer as suitable for the surface, providing and laying 4 mm thick “WP SHIELD APP” Polymer modified membrane with non woven polyester Matt-160 GSM, weight not less than 4 kg/Sq.m having softening point not less than 150 degree centigrade, longitudinal tensile strength not less than 650 N / 5cm tearing strength of 180 N ( P 4180 grade) by torch welding method including minimum 10 cm side over lap, finishing with solar reflective bituminous aluminum paint @ 0.10 Kg/Sq.m complete all as specified and directed by the Engineer-in-charge. |
| 10 | Cement block masonry work in CM 1:6 using good quality, approved cement blocks including charges for ,conveying, scaffolding charges etc.as per departmental instructions. |
| 11 | Cement plastering with CM 1:4,12 mm thick one coat floated hard and trowelled smooth at all levels. |
| 12 | Providing reinforcements to RCC works with MS/Tor steel rods including all charges for onveying, straightening/ uncoiling, cutting, bending, placing rods in position & tying with GI / black annealed tying wire of suitable gauge etc. complete.including cost of reinforcement. |
| 13 | Providing and fixing first quality ceramic glazed wall tiles conforming to IS :15622 (thickness to be specified by the manufacturer) of approved make in all colours,shades of any size as approved by Engineer-in-Charge for dadoing to walls cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477,inaverage 3mm thickness. followed by grouting the joints of flooring tiles having joints of 3mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg),including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 14 | Providing and laying with approvedbrand rectified Glazed Ceramicfloor tiles of size 600x600 mm ormore (thickness to be specified bythe manufacturer), of 1st qualityconforming to IS : 15622, ofapproved make, in suitable colours laid cement based high polymermodified quick-set tile adhesive(Water based) conforming to IS:15477, in average 3mm thickness.with adequate joint spacing of 3mmfollowed by grouting the joints offlooring tiles having joints of 3mm width, using epoxy grout mix of0.70 kg of organic coated filler ofdesired shade (0.10 kg of hardener and 0.20 kg of resin per kg),including filling / grouting andfinishing complete as per direction of EngineerIn-Charge |
| 15 | Waterproofing of Bathroom/ toiletfloor: i) Surface preparation by cleaningthe surface using wire brush inorder to remove all deleteriousmatters and cleaning with water jetspray (if required) includingremoving old worn out tar felt, deleterious materials etc. ii) All pipe penetration shall be sealed with polymer modified mortar(PMM). iii) Saturate the surface with clean water before application ofwaterproof coating system. Once water get dried off apply one coat of High Performance & Ultra flexible polymer modifiedelastomeric waterproofing membrane system of Fosroc-Brushbond ultrafexor equivalent system over the concrete followed a reinforcement fibre mesh over the layer of membrane. iv) Apply two coats of High Performance & Ultra flexiblepolymer modified elastomericwaterproofing membrane system over the above mentioned initial layer after sufficient curing for each layer (Total consumption requirement for all 3 coats is atleast 3kg/m2) |
| 16 | Providing and fixing PVC door of syntex or equivalant make with shutter frame made of extruded plastic section having dimension of 60 x 24 mm or nearest, paneling with single panelhollow plastic section of20 mm thick with average wall thickness of 1 mmand outer frame of door made of extruded plastic section of 48 x 40 mm or nearestincluding providing and fixing all required fittings such as stainless steel butt hinges, PVC tower bolts, PVC handles etc.complete as per manufacturers specifications. |
| 17 | Cleaning thestructural/other surface neatlyat all heights, manually with suitable tools or with high pressure water jet spray (using suitable mechanical means), and scraping if required, to remove the whole accumulateddust, rust, dirt etcas per departmental instructions. |
| 18 | Painting one coat of priming coat on plastered surface (interior/exterior)with approved quality cement primer after cleaning the surface including all cost of materials, labour etc. |
| 19 | Painting two coats with ready mixedplastic emulsion paint of approvedquality and colour specified over the priming coat already done andpaid separately after cleaning thesurface well. |
| 20 | SupplyingandfixingPVC floortrap (single or multy type) ofapproved brand 110 mm size with requiredprovision ofoutlets and inlets as per manufacturersspecifications, cutting and makinggood the walls and floors, etc. complete. |
| 21 | Supplying and fixing 125 mm (5inch) Stainless steel floorgratings (two piece) to PVC trap asper instructions at site |
| 22 | Supplying and fixing approved qualitywhite glazed vitreouschina flat back lipped front urinal of size 430x380x230 mm or nearest sizewith 1No. 15mm PVC heavy type connection and 1 No.15mm CP regulating valve of superior make, CP spreader with flush pipe fixing the urinal to wall with Stainless steel screws with plasticgrips including cutting and makinggood the walls etc. complete as per deptl instructions |
| 23 | Supplying and fixing urinal partitionwith \"flair Division plate\" of Johnsonwhite colouror equivalent |
| 24 | Supplying conveying and fitting550x400mm or nearest size wash hand basin of white glazed vitreous china approved quality with a pair of special alloy bolts for fixing the basin on walls with 1 No. 15 mm heavy type CP brass pillar tap of approved make 1no.heavy type 15mmPVC connection and 1No.15 mm CP regulating valve of superior make ,1No. 15 mmCP waste coupling,32 mm PVC waste pipe with cp learning nut 1No. etc. including cutting and making goodthe walls,etc. complete. |
| 25 | Supplying and fixing at all levels approved quality /brand European type vitreous china white glazed water closet pan with P/S trap and White/Black duro plastic seat and lid with CP brass hinges and CP rubber buffers, 10 litre capacity PVC low level flushing cistern ofapproved makewith all fittings 1No.32mm CP brass flush bend, 1No:15mm superior PVC connection heavy type ,15mm CP regulating valve,cutting and making good thewalls and floors including giving connection to sewer pipe with allnecessary specials,etc. complete as per direction at site |
| 26 | Supplyingto civil storewhite glazed Orisa pan of (Hindustan,Cera or equivalent) 580x440mm size with P/S trap includingall necessary specials,etc. |
| 27 | Supplying to civil store PVC highlevel flushing cistern of 10 Ltr. Capacity of approved make and quality with all required arrangements viz, 1 No. 32 mm PVC flush pipe with learning nut, 1 No. 15 mm superior make 15 mm GM float valve & inlet connection etc.complete. (of make CERA,JOHNSON,KHAJARIA orequivalent) |
| 28 | Supplying Angle valve with wallflange of standard range (CERA, JOHNSON or equivalent) |
| 29 | SupplyingLong body bib cock of standard range CERA/JOHNSON orequivalent type |
| 30 | Supplying to Civil store100 mm CP brass shower rose with 15 mm / 20 mm inlet and of approved brand / manufacturer |
| 31 | Suppling and fixing 600 x20 mm or nearestStainless steelheavyduty approved brand towel rod withbrackets with necessary SS screws,pastic grips etc. complete |
| 32 | Supply and fixing stain less steel hanger unit having min 3 hooks |
| 33 | Supplying and fixingHealth faucets of standard range approved by Engineer-in-Charge (CERA,JOHNSON or equivalent brand) |
| 34 | Supplying and fixing best quality SS soap dish including cost of screws, wooden plugs etc. |
| 35 | Collecting ,conveying and Disposalof building rubbish / debris /similar unserviceable, dismantledor waste materials by manual/mechanical means, includingloading, transporting, unloading toapproved areasfor filling,spreading in layers as perdirections of Engineer-in-charge(20%deduction will be made ifmeasured loose in lorries/fromstack) - For an average lead of 2km |
| 36 | Supplying and fixing Concealed Stop cock ¾ inch \"CERA/ JOHNSON/ PARRYWARE or equivalent type. |
| 37 | Supplying and fixing PVC pipesconforming to IS 4985 class III, 6kg/sq.cm pressure for lines withall required specials such as plainbends, single junctions, elbows,crosses, unions, shoes, door bends,double junctions, vent cowls, etc. with or without door including cutting masonry or concrete floors, sunshades, etc and making the holesgood after finishing the work.wherever necessary and jointing pipes with approved quality resin cement and fixing pipes with MS fixing clamps screwed on to woodenplugs embedded in masonry wherever required and painting the clamps with two coats of enamel paint over one coat primer. This includes testing of joints complete at all levels. for waste water lines 75mm or nearest outer dia. |
| 38 | Supplying and fixing PVC pipesconforming to IS 4985 class III, 6kg/sq.cm pressure for lines with all required specials such as plain bends, single junctions, elbows,crosses, unions, shoes, door bends, double junctions, vent cowls, etc. with or without door including cutting masonry or concrete floors, sunshades, etc and making the holesgood after finishing the work. wherever necessary and jointing pipes with approved quality resin cement and fixing pipes with MS fixing clamps screwed on to woodenplugs embedded in masonry wherever required and painting the clamps with two coats of enamel paint over one coat primer. This includes testing of joints complete at alllevels. for waste water lines:110mm or nearest outer diameter |
| 39 | Supplying, laying and jointing with solvent cement, Rigid PVC pipes conforming to IS 4985 Class V (10 Kg/cm2 pressure rating) for water lines with all required concealed(brass embeded) PVC specials, suchas Tees, bends, elbow, union, reducer etc. with clamps if any including necessary cutting and making good the walls, earth work if required etc.complete -25 mm OD Pipe |
| 40 | Providing man Mazdoor forlabour assistancefor emergency works which are not covered in the Schedule of work. |
