|
| 1 | ITEM NO. 1: EXCAVATION FOR FOUNDATION IN EARTH, SOIL OF ALL TYPES, SAND, GRAVEL AND SOFT MURUM, INCLUDING REMOVING THE EXCAVATED MATERIAL UP TO A DISTANCE OF 50 M. BEYOND THE BUILDING AREA & STACKING AND SPREADING AS DIRECTED, DEWATERING, PREPARING THE BED FOR THE FOUNDATION AND NECESSARY BACK FILLING, RAMMING, WATERING INCLUDING SHORING AND STRUTTING ETC. COMPLETE. (LIFT UPTO 0.00 TO 1.50M.) BY MANUAL MEANS |
| 2 | ITEM NO. 2: EXCAVATION FOR FOUNDATION IN HARD MURUM INCLUDING REMOVING THE EXCAVATED MATERIAL UPTO DISTANCE OF 50 METRES BEYOND THE BUILDING AREA AND STACKING AND SPREADING AS DIRECTED, DEWATERING, PREPARING THE BED FOR THE FOUNDATION AND NECESSARY BACK FILLING, RAMMING, WATERING INCLUDING SHORING AND STRUTTING ETC. COMPLETE. (LIFT UPTO 1.50 M) BY MANUAL MEANS |
| 3 | ITEM NO. 3: EXCAVATION FOR FOUNDATION IN HARD MURUM AND BOULDERS INCLUDING REMOVING THE EXCAVATED MATERIAL UP TO A DISTANCE 50 METRES, BEYOND THE BUILDING AREA AND STACKING AND SPREADING AS DIRECTED, DEWATERING, PREPARING THE BED FOR THE FOUNDATION AND NECESSARY BACK FILLING, RAMMING, WATERING INCLUDING SHORING AND STRUTTING ETC. COMPLETE. (LIFT UPTO 1.5M.) BY MECHANICAL MEANS |
| 4 | ITEM NO. 4: EXCAVATION FOR FOUNDATION IN SOFT ROCK AND OLD CEMENT OR LIME MASONRY FOUNDATIONS INCLUDING REMOVING THE EXCAVATED MATERIAL UPTO A DISTANCE OF 50 METRES BEYOND THE BUILDING AREA AND STACKING AS DIRECTED, INCLUDING DEWATERING, PREPARING THE BED FOR THE FOUNDATION AND NECESSARY BACK FILLING WITH AVAILABLE EARTH/MURUM, RAMMING ,WATERING INCLUDING SHORING AND STRUTTING ETC. COMPLETE. (LIFT FROM 1.5M TO 3.0 M.) BY MECHANICAL MEANS |
| 5 | ITEM NO. 5: PROVIDING SOLING USING 80 MM SIZE TRAP METAL IN 15 CM. LAYER INCLUDING FILLING VOIDS WITH CRUSHED SAND/GRIT, RAMMING, WATERING ETC. COMPLETE. |
| 6 | ITEM NO. 6: PROVIDING AND LAYING CAST IN SITU/READY MIX CEMENT CONCRETE IN M-10 OF TRAP/ GRANITE/ QUARTZITE/ GNEISS METAL FOR FOUNDATION AND BEDDING INCLUDING BAILING OUT WATER, STEEL CENTERING, FORMWORK, LAYING/PUMPING, COMPACTING, ROUGHENING THEM IF SPECIAL FINISH IS TO BE PROVIDED, FINISHING IF REQUIRED AND CURING COMPLETE, WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE ( CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 7 | ITEM NO. 7: PROVIDING PRECONSTRUCTIONAL ANTITERMITE TREATMENT AS PER I.S. 6313 (PART-II) BY TREATING THE BOTTOM SURFACE AND SIDES OF EXCAVATION AT THE RATE OF 5 LITRES OF EMULSION CONCENTRATE OF 1.0 PERCENT OF CLOROPHYRIFOS PER SQUARE METER OF SURFACE AREA COVERING 10 YEARS GUARANTEE ON BOND PAPER. |
| 8 | ITEM NO. 8: PROVIDING PRECONSTRUCTIONAL ANTITERMITE TREATMENT AS PER I.S. 6313 (PART-II) TREATMENT BY TREATING THE BACKFILL IN IMMEDIATE CONTACT WITH FOUNDATION AT THE RATE OF 5 LITRES OF EMULSION CONCENTRATE OF 0.5 PERCENT OF CLOROPHYRIFOS PER SQUARE METRE OF VERTICAL SURFACE AREA COVERING 10 YEARS GUARANTEE ON BOND PAPER. |
| 9 | ITEM NO. 9: PROVIDING PRECONSTRUCTIONAL ANTITERMITE TREATMENT AS PER I.S. 6313 (PART-II) BY TREATING THE TOP SURFACE OF PLINTH FILLING AT THE RATE OF 5 LITRES OF EMULSION CONCENTRATE AT 1.0 PERCENT OFCLOROPHYRIFOSPER SQUARE METRE OF SURFACE AREA COVERING TEN YEARS GUARANTEE ON BOND PAPER. |
| 10 | ITEM NO. 10: FILLING IN PLINTH AND FLOORS WITHAPPROVEDEXCAVATED MATERIAL IN 15CM. TO 20CM. LAYERS INCLUDING WATERING AND COMPACTING ETC. COMPLETE. |
| 11 | ITEM NO. 11: FILLING IN PLINTH AND FLOORS WITH CONTRACTORSMATERIAL/BROUGHT FROM OUTSIDE AND APPROVED BY ENGINEER INCHARGEIN LAYERS OF 15CM. TO 20CM.INCLUDING WATERING AND COMPACTION ETC. COMPLETE. |
| 12 | ITEM NO. 12: PROVIDING AND LAYING CAST IN SITU/READY MIX CEMENT CONCRETE M-25 OF TRAP / GRANITE /QUARTZITE/ GNEISS METAL FOR R.C.C. WORK IN FOUNDATIONS LIKE RAFT, STRIP FOUNDATIONS, GRILLAGE AND FOOTINGS OF R.C.C. COLUMNS AND STEEL STANCHIONS ETC. INCLUDING BAILING OUT WATER, STEEL CENTERING, FORMWORK ,COVER BLOCKS, LAYING/PUMPING, COMPACTION AND CURING ROUGHENING THE SURFACE IF SPECIAL FINISH IS TO BE PROVIDED (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL) ETC. COMPLETE, WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/ CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE ( CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 13 | ITEM NO. 13: PROVIDING AND LAYING CAST IN SITU/READY MIX CEMENT CONCRETE M-25 OF TRAP / GRANITE /QUARTZITE/ GNEISS METAL FOR R.C.C. COLUMNS AS PER DETAILED DESIGNS AND DRAWINGS OR AS DIRECTED INCLUDING STEEL CENTERING, FORMWORK, COVER BLOCKS COMPACTING AND ROUGHENING IF SPECIAL FINISH IS TO BE PROVIDED AND CURING ETC. COMPLETE. (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL).WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/ CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE ( CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 14 | ITEM NO. 14: PROVIDING AND LAYING CAST IN SITU/READY MIX CEMENT CONCRETE IN M-25 OF TRAP/ GRANITE/ QUARTZITE/ GNEISS METAL FOR R.C.C. BEAMS AND LINTELS AS PER DETAILED DESIGNS AND DRAWINGS OR AS DIRECTED INCLUDING STEEL CENTERING, FORMWORK, COVER BLOCKS, LAYING/PUMPING, COMPACTIONAND ROUGHENING THE SURFACE IF SPECIAL FINISH IS TO BE PROVIDED AND CURING ETC. COMPLETE. (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL).WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/ CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE (CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 15 | ITEM NO. 15: PROVIDING AND LAYING CAST IN SITU/READY MIX CEMENT CONCRETE M-25 OF TRAP/ GRANITE / QUARTZITE/ GNEISS METAL FOR R.C.C. SLABS AND LANDINGS AS PER DETAILED DESIGNS AND DRAWINGS INCLUDING STEEL CENTERING, FORMWORK, COVER BLOCKS, COMPACTION, FINISHING THE FORMED SURFACES WITH CEMENT MORTAR 1:3 OF SUFFICIENT MINIMUM THICKNESS TO GIVE A SMOOTH AND EVEN SURFACE OR ROUGHENING IF SPECIAL FINISH IS TO BE PROVIDED AND CURING ETC. COMPLETE.(EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL).WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/ CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE ( CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 16 | ITEM NO. 16: PROVIDING AND LAYING CAST IN SITU/READY MIXCEMENT CONCRETE M-25 OF TRAP/ GRANITE/ QUARTZITE/ GNEISS METAL FOR R.C.C. CHAJJA AS PER DETAILED DESIGN AND DRAWINGS INCLUDING STEEL CENTERING, FORMWORK, COVER BLOCKS, LAYING/PUMPING, COMPACTING AND ROUGHENING THE SURFACE IF SPECIAL FINISH IS TO BE PROVIDED AND CURING COMPLETE. (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL). WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/ CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE (CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 17 | ITEM NO. 17: PROVIDING AND LAYING CAST IN SITU/READY MIX CEMENT CONCRETE IN M-25 OF TRAP/ GRANITE/ QUARTZITE/ GNEISS METAL FOR R.C.C. PARDI OF REQUIRED THICKNESS INCLUDING STEEL CENTERING, FORMWORK, COVER BLOCKS, LAYING/PUMPING, COMPACTING AND ROUGHENING THEM IF SPECIAL FINISH IS TO BE PROVIDED AND CURING COMPLETE. (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL).WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/ CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE ( CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 18 | ITEM NO. 18: PROVIDING AND LAYING CAST IN SITU/READY MIX CEMENT CONCRETE IN M-25 OF TRAP / QUARTZITE /GRANITE /GNEISS METAL FOR R.C.C. WAIST SLAB, AND STEPS OF STAIRCASES AS PER DETAILED DESIGN AND DRAWINGS OR AS DIRECTED INCLUDING STEEL CENTERING, PLYWOOD/ STEEL FORMWORK, STEEL PROPS, LAYING/PUMPING, COMPACTION, FINISHING UNEVEN AND HONEYCOMBED SURFACE WITH C.M. 1:3 OF SUFFICIENT MINIMUM THICKNESS TO GIVE A SMOOTH AND EVEN SURFACE OR ROUGHENING THE SURFACE IF SPECIAL FINISH IS TO BE PROVIDED AND CURING ETC. COMPLETE. (EXCLUDING EINFORCEMENT, INCLUDING COVER BLOCK).(NEWLY LAID CONCRETE SHALL BE COVERED BY GUNNY BAG, PLASTIC, TARPAULIN ETC.) WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/ CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE ( CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 19 | ITEM NO. 19: PROVIDING AND LAYING CAST IN SITU/READY MIX CEMENT CONCRETE IN M-20 OF TRAP/ GRANITE/ QUARTZITE/ GNEISS METAL FOR R.C.C.COPING TO PLINTH OR PARAPET AND SILL OF DOORS AND WINDOWS MOULDED AS PER DETAILED DRAWINGS OR CHAMFERED AS APPROVED BY THE ENGINEER INCLUDING STEEL CENTERING, FORMWORK, COVER BLOCKS, LAYING/PUMPING, COMPACTING , CURING , FINISHING AND ROUGHENING THEM IF SPECIAL FINISH IS TO BE PROVIDED AND CURING COMPLETE. (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL).WITH FULLY AUTOMATIC MICRO PROCESSOR BASED PLC WITH SCADA ENABLED REVERSIBLE DRUM TYPE MIXER/ CONCRETE BATCH MIX PLANT (PAN MIXER) ETC. COMPLETE. WITH FINE AGGREGATE (CRUSHED SAND VSI GRADE FINELY WASHED ETC) |
| 20 | ITEM NO. 20: PROVIDING AND FIXING IN POSITION TMT - FE - 500 BAR REINFORCEMENT OF VARIOUS DIAMETERS FOR R.C.C. PILE CAPS, FOOTINGS, FOUNDATIONS, SLABS, BEAMS COLUMNS, CANOPIES, STAIRCASE, NEWELS, CHAJJAS, LINTELS PARDIS, COPINGS, FINS, ARCHES ETC. AS PER DETAILED DESIGNS, DRAWINGS AND SCHEDULES. INCLUDING CUTTING, BENDING, HOOKING THE BARS, BINDING WITH WIRES OR TACK WELDING AND SUPPORTING AS REQUIRED COMPLETE. |
| 21 | ITEM NO. 21: PROVIDING FLY ASH BRICK MASONRY WITH CONVENTIONAL / I.S. TYPE FLY ASH BRICKSIN C.M. 1:6 IN FOUNDATION AND PLINTH INCLUDINGBAILING OUT WATER MANUALLY STRIKING JOINTS, RACKING OUT JOINTS WATERING AND SCAFFOLDING ETC. COMPLETE. |
| 22 | ITEM NO. 22: PROVIDING FLY ASH BRICK MASONRY WITH CONVENTIONAL/ I.S. TYPE BRICKS IN CEMENT MORTAR 1:6 IN SUPERSTRUCTURE INCLUDING STRIKING JOINTS, RAKING OUT JOINTS, WATERING AND SCAFFOLDING ETC. COMPLETE |
| 23 | ITEM NO. 23: PROVIDING INTERNAL CEMENT PLASTER 20MM THICK IN SINGLE COATS IN CEMENT MORTAR 1:4 WITHOUT NEERU FINISH, TO CONCRETE, BRICK SURFACE, IN ALL POSITIONS INCLUDING SCAFFOLDING AND CURINGETC.COMPLETE. |
| 24 | ITEM NO. 24: PROVIDING AND APPLYING PLASTER WITH PLASTER OF PARIS IN 6MM THICKNESS TO PREVIOUSLY PLASTER SURFACE IN ALL POSITION INCLUDING PREPARING THE SURFACE SCAFFOLDING ETC. COMPLETE. |
| 25 | ITEM NO. 25: PROVIDING AND APPLYING PLASTER / WALL PUNNING WITH PLASTER OF PARIS ( WITH PLASTER OF PARIS MATERIAL OF AMBUJA / MOR CHAP OR EQUIVALENT MAKE ) IN 10 TO 13 MILLIMETER THICKNESS TO PREVIOUSLY PLASTERED SURFACE / OR ON NEWLY BRICK SURFACE ( EXCLUDING ROUGH CAST PLASTER ) IN ALL POSITION INCLUDING PREPARING AND FINISHING THE SURFACE SCAFFOLDING ETC.COMPLETE. |
| 26 | ITEM NO. 26: PROVIDING SAND FACED PLASTER EXTERNALLY IN CEMENT MORTAR USING APPROVED SCREENED SAND, IN ALL POSITIONS INCLUDING BASE COAT OF 15 MM THICK IN CEMENT MORTAR 1:4 USING WATERPROOFING COMPOUND AT 1 KG PER CEMENT BAG CURING THE SAME FOR NOT LESS THAN 2 DAYS AND KEEPING THE SURFACE OF THE BASE COAT ROUGH TO RECEIVE THE SAND FACED TREATMENT 6 TO 8 MM THICK IN CEMENT MORTAR 1:4 FINISHING THE SURFACE BY TAKING OUT GRAINS AND CURING FOR FOURTEEN DAYS SCAFFOLDING ETC.COMPLETE. |
| 27 | ITEM NO. 27: PROVIDING AND FIXING CHICKEN MESH OF 22 GAUGE, WITH ABOUT 30 CM. WIDTH AT THE JUNCTION OF R.C.C MEMBERS AND BRICK WORK, OF APPROVED QUALITY INCLUDING FIXING MESH IN POSITION BY NECESSARY DRILLING IN CONCRETE /B.B.MASONRY AND OR TYING BY BINDING WIRE ETC. COMPLETE. |
| 28 | ITEM NO. 28: PROVIDING GROOVE TO REQUIRED SIZE AT SPECIFIED LOCATION AS DIRECTED BY ENGINEER, AT JUNCTION OF BRICK MASONRY WALL AND R.C.C BEAMS OR COLUMN, AT JUNCTION OF COMPOSITE MASONRY, INCLUDING SCAFFOLDING, FINISHING, CURING ETC. COMPLETE… |
| 29 | ITEM NO. 29: PROVIDING AND LAYING VITRIFIED MATT FININSH TILESHAVING SIZE 590 MM TO 605 MM X TO 605 MM OF 8 TO 10 MM THICKNESS AND CONFIRMING IS. 15622-2006 (GROUP BLA) OF APPROVED MAKE, SHADE AND PATTERN FOR FLOORING IN REQUIRED POSITION LAID ON A BED OF 1:4 CEMENT MORAR INCLUDING NEAT CEMENT FLOAT, FILLING JOINTS, CURING AND CLEANING ETC. COMPLETE. A) FLOORING |
| 30 | ITEM NO. 30: PROVIDING AND LAYING VITRIFIED MIRROR / GLOSSY FINISH TILESHAVING SIZE 590 MM TO 605 MM X 590 MM TO 605 MM OF 8 TO 10 MM THICKNESS AND CONFIRMING TO IS. 15622-2006 ( GROUP BLA) OF APPROVED MAKE, SHADE AND PATTERN FOR FLOORING IN REQUIRED POSITION LAID ON A BED OF 1:4 CEMENT MORTAR INCLUDING NEAT CEMENT FLOAT, FILLING JOINTS, CURING AND CLEARINGETC. COMPLETE.B) SKIRTING |
| 31 | ITEM NO. 31: PROVIDING AND LAYING TELEPHONE BLACK / AMBA WHITE / CADBURYBROWN / RUBY RED / OCEAN BROWN GRANITE STONE OF 18 TO 20 MM THICK FOR DOOR FRAME/ DADO/ WINDOW BOXING ETC. ON C.M. 1:6 INCLUDING FILLING JOINTS WITH POLYMER BASE FILLER NOSING THE SHARP EDGES WHEREVER NECESSARY, CURING,ETC. COMPLETE. |
| 32 | ITEM NO. 32: PROVIDING SILLS OF REQUIRED MATERIAL 20MM TO 25MM THICK, ON A BED OF CEMENT MORTAR 1:4 INCLUDING CEMENT FLOAT, FILLING JOINTS WITH NEAT CEMENT SLURRY, CURING, POLISHING, ROUNDING EDGES, CLEANING COMPLETE. B) GRANITE |
| 33 | ITEM NO. 33: PROVIDING AND FIXING MACHINE CUT MACHINE POLISHED 18 MM TO 20 MM THICK TELEPHONE BLACK / AMBA WHITE / CAT BARY BROWN / RBI RED / OCEAN BROWN GRANITE STONE FOR TREADS AND RISERS OF STEPS AND STAIRCASES OF APPROVED COLOUR AND SHADE WITH ROUNDED MOULDING AND THREE GROOVED LINE FOR THE TREADS ON BED OF 1:4 CEMENT MORTAR INCLUDING FLOAT FILLING JOINTS WITH NEAT CEMENT SLURRY CURING POLISHING AND CLEANINGETC. COMPLETE. |
| 34 | ITEM NO. 34: PROVIDING AND FIXING FRAME WITH / WITHOUT VENTILATOR OF SIZE AS SPECIFIED WITH COUNTRY CUTTEAK WOODFOR DOORS AND WINDOWS INCLUDING CHAMFERING, ROUNDING, REBATING, IRON HOLDFAST OF SIZE 300MM X 40MM X 5MM WITH OIL PAINTING, ETC. COMPLETE |
| 35 | ITEM NO. 35: PROVIDING AND FIXING SOLID CORE FLUSH DOOR SHUTTER IN SINGLE LEAF 32 MM THICK DECORATIVE TYPE OF EXTERIOR GRADE AS PER DETAILED DRAWINGS APPROVED FACE VENEERS 3 MM THICK ON BOTH FACES OR AS DIRECTED, ALL NECESSARY BEADS, MOULDINGS AND LIPPING, WROUGHT IRON HOLD FASTS, CHROMIUM PLATED FIXTURES AND FASTENINGS, WITH BRASS MORTISE LOCK, CHROMIUM PLATED HANDLES ON BOTH SIDES, AND FINISHING WITH FRENCH POLISH ETC. COMPLETE. |
| 36 | ITEM NO. 36: PROVIDING AND FIXING FIBER GLASS REINFORCED POLYSTER DOOR SHUTTER 30 MM THICK AS PER IS 14856 (2000) (REAFFIRMED 2006) WITHOUT VENTILATOR INCLUDING CHROMIUM PLATED FIXTURES AND FASTENING WITH CHROMIUM PLATED HANDLES ON BOTH SIDES, ETC COMPLETE. |
| 37 | ITEM NO. 37: PROVIDING AND FIXING MILD STEEL GRILL WORK FOR WINDOWS, VENTILATORS ETC. 20 KG/SQM AS PER DRAWING INCLUDING FIXTURES, NECESSARY WELDING & PAINTING WITH ONE COATS OF ANTICORROSIVE PAINT & TWO COATS OF OIL PAINTING COMPLETE. |
| 38 | ITEM NO. 38: PROVIDING AND FIXING IN POSITION (AS PER 1868 / 1982) ALUMINIUM SLIDING WINDOW OF THREE TRACKS WITH RECTANGULAR PIPE 95 X 38.10 X 0.90 MM AT WEIGHT 0.637 KG/RMT. WITH WINDOW FRAME BOTTOM TRACK SECTION 92 X 31.75 X 1.30 MM AT WEIGHT 1.070 KG/RMT.. TOP AND SIDE TRACK SECTION 92 X 31.75 X 1.30 MM AT WEIGHT 0.933 KG/RMT. THE SHUTTER SHOULD BE OF BEARING BOTTOM 40 X 18 X 1.25 MM AT WEIGHT 0.417 KG/RMT. INTER LOCKING SECTION 40 X 18 X 1.10 MM AT WEIGHT 0.469 KG/RMT. AND HANDLE AND TOP SECTION 40 X 18 X 1.25 MM AT WEIGHT O.417 KG/RMT. AS PER DETAILED DRAWINGS AND AS DIRECTED BY ENGINEER-IN-CHARGE WITH ALL NECESSARY ALUMINIUM SECTIONS FIXTURES AND FASTENINGS SUCH AS ROLLER BEARING IN NYLON CASTING AND SELF LOCKING CATCH FITTED IN VERTICAL SECTION OF SHUTTER INCLUDING 5 MM THICK PLAIN GLASS AND ALUMINIUM MOSQUITO NET SHUTTER WITH STAINLESS STEEL JAIL WITH ALL REQUIRED SCREWS AND NUTS ETC, COMPLETE.WITH POWDER COATING WITHOUT BOX |
| 39 | ITEM NO. 39: PROVIDING AND FIXING COLLAPSIBLE STEEL GATE IN ONE / TWO LEAVES WITH HOT ROLLED VERTICAL CHANNELS OF 18 X 9 X 3 MM MINIMUM SIZE, CROSSINGS OF M.S. FLATS OF SIZE 18 X 5 MM T OR E SECTION FOR RUNNER OF MINIMUM 40 X 6 MM SIZE FOR FLANGE, M.S. FLAT FOR TOP RUNNER OF MINIMUM SIZE 40 X 12 MM WITH ROLLER WHEELS CONFIRMING TO GRADE F.G. 150 FITTED WITH SNAP HEADED RIVETS OF MINIMUM SIZE 6 MM MAX. SPACING OF VERTICAL CHANNELS BE 100 MM ENCLOSED GATE POSITION AND CLEAR SPACE OF 150 MM BETWEEN TWO SETS OF CROSSINGS WITH HOLD FASTS, STOPPERS, SPACES, HANDLES, LOCKING ARRANGEMENT AND ONE COAT OF RED LEAD PRIMER & OIL PAINTING ETC. COMPLETE. (I.S. 10521-1983). |
| 40 | ITEM NO. 40: PROVIDING AND APPLYING PRIMING COAT ON CONCRETE/ MASONARY/ ASBESTOS CEMENT PLASTERED SURFACES INCLUDING SCAFFOLDING IF NECESSARY, PREPARING THE SURFACE BY THOROUGHLY CLEANING OIL, GREASE, DIRT AND OTHER FOREIGN MATTER AND SAND PAPERING AS REQUIRED ETC. COMPLETE. |
| 41 | ITEM NO. 41: PROVIDING AND APPLYING PLASTIC EMULSION PAINT OF APPROVED QUALITY, COLOUR AND SHADE TO OLD SURFACE IN THREE COATS INCLUDING SCAFFOLDING, PREPARING THE SURFACE. (EXCLUDING PRIMER COAT) ETC. COMPLETE. |
| 42 | ITEM NO. 42: PROVIDING AND APPLYING ONE COAT OF SEAL CEMENT PRIMER OF APPROVED MANUFACTURE AND SHED INCLUDING SCAFFOLDING PREPARING THE SURFACE BY CLEANING DIRT AND OTHER FOREIGN MATTERS, SCRAPPING IF NECESSARY INCLUDING SCAFFOLDING ETC. COMPLETE. |
| 43 | ITEM NO. 43: PROVIDING AND APPLYING TWO COATS OFEXTERIOR ACRAYLIC EMULSION PAINT CONFIRMING TO CORRESPONDING I.S. OF APPROVED MANUFACTURE AND OF APPROVED COLOUR TO THE PLASTERED SURFACES INCLUDING CLEANING ,PREPARING THE PLASTER SURFACE, APPLYING PRIMER COAT ,SCAFFOLDING IF NECESSARY , AND WATERING THE SURFACE FOR TWO DAYS ETC COMPLETE. |
| 44 | ITEM NO. 44: PROVIDING CEMENT BASED WATER PROOFING TREATMENT TO TERRACES (INDIAN WATER PROOFING OR ALIKE) WITH BRICK BATS LAID IN REQUIRED SLOPE TO DRAIN THE WATER FOR ANY SPAN AFTER CLEANING THE BASE SURFACE. APPLYING A COAT OF CEMENT SLURRY ADMIXED WITH APPROVED WATER PROOFING COMPOUND AND LAYING THE BRICK BATS ON BOTTOM LAYER IN C.M.1:5 ADMIXED WITH APPROVED WATER PROOFING COMPOUND FILLING UP TO HALF DEPTH OF BRICK BATS, CURING THIS LAYER FOR 3 DAYS, APPLYING CEMENT SLURRY OVER THIS LAYER JOINTS OF BRICK BATS WITH C.M.1:3 ADMIXED WITH APPROVED WATER PROOFING COMPOUND AND FINALLY TOP FINISHING WITH AVERAGE 20 MM. THICK LAYERS OF SAME MORTAR ADDED WITH JUTE FIBER AT 1 KG PER BAG INCLUDING FINISHING THE SURFACE SMOOTH WITH CEMENT SLURRY ADMIXED WITH APPROVED WATER PROOFING COMPOUND. MARKING FINISHED SURFACE WITH FALSE SQUARES OF 300MM X 300 MM. MAKING THE JUNCTIONS AT THE PARAPET ROUNDED AND TAPERED TOP FOR REQUIRED HEIGHT, WITH DRIP MOULD AT THE JUNCTION OF PLASTER AND PARAPET AND CURING AND COVERING 10 YEARS GUARANTEE AGAINST LEAKPROOFNESS ON COURT FEE STAMP PAPER OF RS. 500/- INCLUDING PONDING TEST ETC. COMPLETE. |
| 45 | ITEM NO. 45: PROVIDING AND FIXING P.V.C. RAIN WATER PIPES OF 110MM OUTER DIAMETER AND HAVING WALL THICKNESS OF 2.2 TO 2.7 MM CONFIRMING TO I.S. 13592-1992 INCLUDING PROPER RAINWATER RECEIVING RECESS WITH P.V.C. PLUG, BEND, NECESSARY FITTINGS, SUCH AS, OFFSETS, SHOES, INLUDING FIXING THE PIPE ON WALL USING APPROVED WOODEN CLEATS PROJECTING 25MM TO 40MM FROM FACE OF WALL A FIXING WITH CLIPS OF APPROVED QUALITY AND NUMBER ,FILING THE JOINT USING RUBBER GASKET WITH SOLVENT CEMENT AND PROPERLY RESTING THE SHOE OF PIPES ON C.C. OR MASONRY BLOCKS, INCLUDING NECESSARY SCAFFOLDING AND MAINTENANCE FOR 3 YRS FOR ANY LEAKAGES OR DISLOCATIONS OF PIPES. ALL THE P.V.C. FITTINGS AND ADDITIONAL 2 PIECE SOCKET CLIPS SHALL BE GOT APPROVED FROM ENGINEER IN CHARGE ETC. COMPLETE. (THE CONTRACTOR SHALL GIVE 3 YRS GUARANTEE BOND FOR PAYMENT) |
| 46 | ITEM NO. 46: PROVIDING AND FIXING MAT FINISH STAINLESS STEEL (OF 302 GRADE ) RAILING WITH TOPPIPE OF 50 MM DIA. AND VERTICAL PIPE OF 38 MM DIA AT 0.60 M C/C OR AS REQUIRED AND HORIZONTAL PIPES OF 25 MM DIA IN THREE ROWS, ALL PIPES OF 2 MM THICK INCLUDING BUFFING,FABRICATING FIXTURES AND FASTENING INCLUDING PIPE BASE OF APPROPRIATE DIAMETER AND BALL BASE OF 75 MM DIA ABOVE NEWEL POST OF 75 MM DIAMETER ETC. COMPLETE (PRIOR APPROVAL OF SAMPLE AND BRAND BY EX.ENGINEER IS NECESSARY BEFORE USE)…. |
| 47 | ITEM NO. 47: PROVIDING AND LAYING MACHINE CUT MACHINE POLISHED KOTA STONE FLOORING 25MM TO 30MM THICK AND REQUIRED WIDTH IN PLAIN/ DIAMOND PATTERN ON BED OF 1:6 C. M. INCLUDING CEMENT FLOAT, FILLING JOINTS WITH NEAT CEMENT SLURRY, CURING, POLISHING AND CLEANINGETC. COMPLETE. |
| 48 | ITEM NO. 48: PROVIDING AND FIXING 40MM DIAMETER AND 1.5MM THICK STAINLESS STEEL HAND RAILING IN S.S.304 GRADE INCLUDING FABRICATING ,FIXTURES, ERRECTING , NECESSARY WELDING , GRINDING , FINISHING, BUFFING TO STAINLESS STEEL PIPE ETC. COMPLETE |
| 49 | ITEM NO. 49: PROVIDING AND LAYING ROUGH SHAHABAD STONE FLOORING 25MM TO 30MM THICK AND OF REQUIRED WIDTH IN PLAIN/ DIAMOND PATTERN ON A BED OF 1:6 C.M. INCLUDING CEMENT FLOAT, STRIKING JOINTS, POINTING IN CEMENT MORTAR 1:3 CURING AND CLEANINGETC. COMPLETE. |
| 50 | ITEM NO. 50: DISMANTLING STONE MASONRY IN LIME OR CEMENT MORTAR INCLUDING STACKING THE MATERIALS AS DIRECTED WITH ALL LEADS, LIFTS ETC. COMPLETE. |
| 51 | ITEM NO. 51: PROVIDING PATTI/ BAND 100MM WIDE ON PLASTERED SURFACE 12 MM TO 15 MM THICK IN C.M. 1:3 LINE AND LEVEL INCLUDING NEAT FINISHING SCAFFOLDING CURING ETC. COMPLETE. |
| 52 | ITEM NO. : 52 PROVIDING AND FIXING TOILET SET FOR DIFFERENTLY ABLED PERRSONS CONSIST OF FLOOR MOUNDTED WHITE VITROUS CHINA WATER CLOSET INCLUDING 6 LITRE CAPACITY WHITE VITREOUS CHINA FLUSHING CISTERN WITH RAISED SOFT-PUSH BUTTON, WHITE VITREOUS CHINA WASH BASIN OF SIZE 46 x 36 CM AND ONE ON SS 304 HINGED RAIL 76 CMS & THREE NO SS 304 OF (GRAB BAR) 60 CMS ALL INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS WHEREVER REQUIRED, SEAT COVER, CISTERN & WASH BASIN FITTINGS, NUTS, BOLTS AND GASKET ETC COMPLETE OF MAKE HINDWARE (MATRIX SERIES 70002)/ CERA OR EQUIVALENT AS PER THE DIRECTION OF ENGINEER IN CHARGE (INO51-63, PGNO 369) (STATE SSR) ITEM SPEC. (AS DIRECTED BY ENGINEER IN CHARGE) |
| 53 | ITEM NO. : 53 PROVIDING AND LAYING IN WALLS/ CEILINGS/ FLOORS 80MM DIA MEDIUM GRADE HAVING EMBOSSED AS ISI MARK GALVANISED IRON PIPES OF 8.57 KG/ METRE NECESSARY FITTING REMARKING GOOD THE DEMOLISHED PORTION WITTH FITTING TRENCHES AND WITH PRIMER OF ANTI-CORROSIVE OIL PAINT, 2 COATS COMP. INCLUDING NECESSARY SCAFFOLDING AND REMOVING EXISTING PIPE LINE IF NECESSARY AND CONVEYING AND STACKING THE SAME IN PWD CHOWKY OR AS DIRECTED ETTC. COMP (INO43-07, PGNO 287) (STATE SSR) ITEM SPEC. (BD.V.5 PAGE NO. 551) |
| 54 | ITEM NO. : 54 PROVIDNG AND LAYING IN TRENCHES 50MM DIA MEDIUM GRADE HAVING EMBOSSED AS ISI MARK GALVANISED IRON PIPES? OF 5.17 KG/ METER NECESSARY FITTING REMAKING GOOD THE DEMOLISED PORTION WITH FILLING TRENCHES AND WITH PRIMER OF ANTI-CORROSIVE OIL PAINT, 2 COATS INCLUDING REMOVING EXISTING PIPE LINE IF NECESSARY AND CONVEYING AND STACKING THE SAME IN PWD CHOWKY OR AS DIRECTED ETC. COM. (INO41-23, PGNO 269) (STATE SSR) ITEM SPEC (BD.V.5 PAGE NO. 551) |
| 55 | ITEM NO. 55: PROVIDING , LAYING & FIXING ,JOINTING SUPREME ECO- DRAIN 110 MM SN 8 NU- DRAIN UPVC PIPES OR OF EQUIVALENT MAKE, MANUFACTURE AS PER EN 13476 OR EQUIVALENT AS PER I.S.15328 WITH FITTINGS SUCH A BENDS, TEES, COUPLER, ETC, JOINTING WITH RUBBER LUBRICANT INCLUDING NECESSARY EXCAVATION, TRENCH REFILLING WITH SELECTIVE EXCAVATED MATERIAL ETC. COMPLETE. |
| 56 | TEM NO. 56: PROVIDING , LAYING & FIXING ,JOINTING SUPREME ECO- DRAIN 160 MM SN 4 NU- DRAIN UPVC PIPES OR OF EQUIVALENT MAKE, MANUFACTURE AS PER EN 13476 OR EQUIVALENT AS PER I.S.15328 WITH FITTINGS SUCH A BENDS, TEES , COUPLER, ETC, JOINTING WITH RUBBER LUBRICANT INCLUDING NECESSARY EXCAVATION, TRENCH REFILLING WITH SELECTIVE EXCAVATED MATERIALETC. COMPLETE. |
| 57 | ITEM NO. 57: PROVIDING AND FIXING IN POSITION UPVC ULTRA VIOLET STABILIZED 110 MM OUTER DIAMETER COWL DOME CONFIRMING TO I.S.-4985 INCLUDING MAKING JOINTS WITH SOLVENT CEMENT ETC. COMPLETE |
| 58 | ITEM NO. 58: PROVIDING AND CONSTRUCTING BRICK MASONRY INSPECTION CHAMBER 60CM X 45CM X 90CM INCLUDING 1:4:8 CEMENT CONCRETE FOUNDATION 1:2:4 CEMENT CONCRETE CHANNELS HALF ROUND G.S.W. PIPES, BRICK MASONRY, PLASTERING FROM INSIDE AND WITH FRAME FIXED IN CEMENT CONCRETE WITH R.C.C. COVER MEDIUM DUTY 140 KG WITH FRAME ETC COMPLETE. |
| 59 | ITEM NO. 59: PROVIDING AND CONSTRUCTING BRICK MASONRY INSPECTION CHAMBER 90CM X 45CM X 90CM INCLUDING 1:4:8 CEMENT CONCRETE FOUNDATION 1:2:4 CEMENT CONCRETE CHANNELS HALF ROUND G.S.W.PIPES, BRICK MASONRY, PLASTERING FROM INSIDE AND WITH FRAME FIXED IN CEMENT CONCRETE WITH R.C.C. COVER MEDIUM DUTY 140 KG WITH FRAME ETC COMPLETE. |
| 60 | ITEM NO. 60: PROVIDING AND FIXING WHITE GLAZED EARTHENWARE WASH HAND BASIN OF 63CM X 45CM SIZE INCLUDING COLD WATER PILLAR TAP/COLD AND HOT WATER PILLAR TAP BRACKETS, RUBBER PLUGS AND BRASS CHAIN, STOP TAP AND NECESSARY PIPE CONNECTION INCLUDING P.V.C. WASTE PIPE AND TRAP UP TO THE OUTSIDE FACE OF THE WALL. |
| 61 | ITEM NO. 61: PROVIDING AND FIXING 15CM X 10CM SALT GLAZED STONEWARE GULLY TRAP IN CEMENT CONCRETE 1:4:8 OUTSIDE THE BUILDING INCLUDING CAST IRON GRATING IN THE SINK, CONNECTING GLAZED STONEWARE PIPE, BRICK MASONRY CHAMBER WITH CAST IRON LID AND CAST IRON GRATING FOR THE GULLY TRAP. |
| 62 | ITEM NO. 62: PROVIDING AND FIXING 450MM X 550MM SIZE SUPERIOR TYPE BELGIUM MIRROR WITH 16MM DIA. NICKEL PLATED TOWEL ROD ETC. COMPLETE. |
| 63 | ITEM NO. 63: PROVIDING AND FIXING 1ST CLASS WHITE GLAZED EARTHENWARE ORISSA TYPE W.C. PAN 580 MM DIA INCLUDING P OR S TRAP CAST IRON SOIL AND VENT PIPE UPTO THE OUTSIDE FACE OF THE WALL (1:5:1 0) CEMENT CONCRETE BEDDING 15 MM THICK, 10 LITER P.V.C. FLUSHING CISTERN WITH ALL NECESSARY PIPE CONNECTION ETC. COMPLETE. |
| 64 | ITEM NO. 64: PROVIDING AND FIXING H.D.P CONTAINER SYNTEX OR ALIKE ONE PIECE MOULDED WATER TANK MADE OUT OF LOW DENSITY POLYTHYLER AND BUILT CORRUGATION INCLUDING OF DELIVERY UP TO DESTINATION HOISTING AND FIXING OF ACCESSORIES SUCH AS INLET, OUTLET OVERFLOW OF ALL TANKS CAPACITY ABOVE 1000 TO 20,000 LITRES. |
| 65 | ITEM NO. 65: PROVIDING AND FIXING 75 MM DIA STABILISER PIPE/ P.V.C. SOIL VENT/WASTE PIPE AND WITH NECESSARY FIXTURES AND FITTING SUCH AS BENDS, TEES, SINGLE JUNCTIONS, SLOTTED VENT, CLAMPS ETC. COMPLETE |
| 66 | ITEM NO. 66: PROVIDING AND FIXING ON WALLS/CEILING/FLOOR 20 MM DIA. CPVC PIPE WITH NECESSARY FITTINGS, REMAKING GOOD THE DEMOLISHED PORTION ETC. COMPLETE. INCLUDING REMOVING EXISTING PIPE LINE IF NECESSARY AND CONVEYING AND STACKING THE SAME IN PWD CHOWKY OR AS DIRECTED ETC. COMPLETE. |
| 67 | ITEM NO. 67: PROVIDING AND FIXING ON WALLS/ CEILING/ FLOOR 25 MM DIA. CPVC PIPE WITH NECESSARY FITTINGS, REMAKING GOOD THE DEMOLISHED PORTION ETC. COMPLETE. INCLUDING REMOVING EXISTING PIPE LINE IF NECESSARY AND CONVEYING AND STACKING THE SAME IN PWD CHOWKY OR AS DIRECTED ETC. COMPLETE. |
| 68 | ITEM NO. 68: PROVIDING AND FIXING ON WALLS /CEILING/ FLOOR 40 MM DIA. CPVC PIPE WITH NECESSARY FITTINGS, REMAKING GOOD THE DEMOLISHED PORTION ETC. COMPLETE. INCLUDING REMOVING EXISTING PIPE LINE IF NECESSARY AND CONVEYING AND STACKING THE SAME IN PWD CHOWKY OR AS DIRECTED ETC. COMPLETE. |
| 69 | ITEM NO. 69: PROVIDING AND FIXING 10 CM PVC NAHANI TRAP WITH GRATING ETC. COMPLETE. |
| 70 | ITEM NO. 70: PROVIDING AND FIXING C.P.TWO WAY BIB COCK JAQUAR MAKE OR EQUIVALENT CONTINENTAL (CAT.NO. CON-041) INCLUDING NECESSARY SOCKETS/UNION NUT ETC. COMPLETE. |
| 71 | ITEM NO. 71: PROVIDING AND FIXING EUROPEAN TYPE WALL-HUNG WHITE WATER CLOSET OF PARYWARE / HINDWARE WITH PUSH VALVE CONCEALED TYPE WITH COVER PLATE 32MM SIZE OF JAQUAR MAKE SERIES FLV-1095 INCLUDING SOIL PIPE ,VENT PIPE UP TO OUTSIDE FACE OF WALL ,100MM DIA. G.I. PLUG BEND INLET PIPE ALL FITTINGS, CUTTING& MAKING GOOD WALLS, FLOORS ETC. COMPLETE. |
| 72 | ITEM NO. 72: PROVIDING AND FIXING BOARD DISPLAYING INFORMATION, SUCH AS \"NAME OF WORK, TENDER COST, NAME OF CONTRACTOR, WORK COMPLETION AND LIABILITY PERIOD ETC\", HAVING RECTANGULAR SHAPE OF 1.20M X 0.90M SIZE MADE OUT 18 GAUGE (1.25MM) THICK MILD STEEL SHEET PAINTED WITH ONE COAT OF ZINC CHROMATE STOVING PRIMER AND TWO COATS OF ENAMEL PAINT ON FRONT SIDE AND GREY STOVE ENAMEL ON BACK SIDE AND BORDER / MESSAGES / SYMBOLS ETC. WITH APPROVED COLOUR SHADE PAINT COMPLETE, ON M.S.ANGLE OF SIZE 35 X 35 X 3 MM FRAME WITH PROPERLY CROSS BRACED M.S. ANGLES OF SIZE 35MMX35MMX3MM DULY PAINTED INCLUDING TWO M.S. ANGLE IRON POSTS OF SIZE 65 MM X 65 MM X 6 MM, 3.65 M LONG PAINTED WITH ALTERNATE BLACK AND WHITE BANDS OF 25 CM WIDTH INCLUDING ALL FIXTURES ETC.AND FIXING THE BOARDS IN 1:4:8 CONCRETE BLOCK OF SIZE 60 CM X 60 CM X 75 CM INCLUDING, EXCAVATION, REFILLING, TRANSPORTATION, AND LABOUR ETC COMPLETE. SPEC. NO. AS DIRECTED BY ENGINEER IN CHARGE |
| 73 | ITEM NO. 73: PROVIDING DETAILED LAYOUT PLAN OF AREA IN SCALE 1:500 INCLUDING CARRYING OUT CONTOUR SURVEY & DETAILED ENGINEERING PLANE TABLE SURVEY WITH THE HELP OF 20\"\". THE DOLOMITE AREA MEASUREMENT OF THE PLOT AND STRUCTURES, TREES, OVER HEAD LINE AND UNDER GROUND SERVICE AMENITIES WITHIN THE AREA, WITH TRIAGULAR METHOD AND GIVING DETAILES OF THE STRUCTURES, SUCH AS TOTAL AREA, TYPE OF BUILDING & DISTANCE FROM ALL CORNERS TAKING TRIAL PIT 0.5X0.5X2.00 M.-2NOS. PER ACRE AND COLLECTION OF RECORD FROM CITY SURVEY / D.I.L.R. AUTHORITIES AND AUTHENTICATION. THE PLAN SHALL BE TRACED ON 75 MICRON POLYSTER FILM AND SHALL BE SUBMITTED ALONG WITH THREE AMONIA PRINTS. THE CONTOUR LEVELS SHALL BE MARKED AT 0.5. METER INTERVALS. NOTE:- THE ITEMS INCLUDES- 1)TRAVERSING WORK WITH THEODOLITE AND STEEL TAPE. 2) LEVELLING GRID WORK OF THE TERRAIN. 3)DETAILED ENGINEERING SURVEY AND CONTOURING WORK OF THE TERRAIN.4)PLOTTING WORK.5)COLLECTION OF RECORD.A) UP TO 1 ACRE |
| 74 | ITEM NO. 74: PREPARATION OF AUTOCAD DRAWING WITH COLOUR PRINT FOR BUILDING / BRIDGE / ROAD/ CD WORKS IN REQUIRED SIZE ETC. COMPLETE. - A-0 SIZE |
| 75 | ITEM NO. 75: PROVIDING AND CONSTRUCTING DUCTILE IRON CIRCULAR MANHOLE 45 CM DIA. AT TOP 90 CM AT BOTTOM UP TO 1.80 METER TO 2.70 METER DEPTH INCLUDING EXCAVATION, LAYING 1:4:8 CEMENT CONCRETE BEDDING 15 CM THICK BURNT BRICK MANSONRY WITH 1:1 CEMENT MORTAR PLASTER 25 MM THICK INSIDE AND OUTSIDE 20 MM (1:3) DUCTILE IRON HEAVY TYPE COVER WITH RING 125 KG IN WEIGHT. HIGH STRENGTH. MORE LIFE AND DURABILITY, GOOD ANTISKID GRIP, SUITABLE TO HEAVY THEATRIC LOADING, LIGHT WEIGHT CASTING AFTER COST BENEFITS FOR TRANSPORTATION REFILLING ETC. AS PER REQUIREMENT. WITH PRIOR APPROVAL OF CONCERNED SUPERITENDING ENGINEER. |
| 76 | ITEM NO. 76: CLEARING GRASS AND REMOVAL OF RUBBISH UP TO A DISTANCE OF 50 METRES OUTSIDE THE PERIPHERY OF THE AREA . |
| 77 | ITEM NO. 77: EXCAVATION FOR ROADWAY IN EARTH, SOIL OF ALL SORTS, SAND, GRAVEL OR SOFT MURUM INCLUDING DRESSING SECTION TO THE REQUIRED GRADE, CAMBER AND SIDE SLOPES AND CONVEYING THE EXCAVATED MATERIALS WITH ALL LIFTS UPTO A LEAD OF 50M. AND SPREADING FOR EMBANKMENT OR STACKING AS DIRECTED. |
| 78 | ITEM NO. 78: SUPPLYING HARD MURUM/ KANKAR AT THE ROAD SITE, INCLUDING CONVEYING AND STACKING COMPLETE. |
| 79 | ITEM NO. 79: SPREADING HARD MURUM/ SOFT MURRUM/ GRAVEL OR KANKAR FOR SIDE WIDTH COMPLETE |
| 80 | ITEM NO. 80: COMPACTING THE HARD MURUM SIDE WIDTHS INCLUDING LAYING IN LAYERS ON EACH SIDE WITH VIBRATORY ROLLER INCLUDING ARTIFICIAL WATERING ETC. COMPLETE. |
| 81 | ITEM NO. 81: PROVIDING AND ERECTING CHAIN LIN FENCING 1.6M HEIGHT WITH G.I. CHAIN LINK OF SIZE 50 X 50MM 8 GUAGE THICK AND FIXED 75MM ABOVE GROUND LEVEL ON VERTICAL M.S. ANGLE OF 40 X 40 X 6 MM SIZE INCLUDING EXCAVATING PITS FOR FOUNDATION AND EMBEDDED IN CC BLOCK OF 1:4:8 MIX OF SIZE 450 X 450 X 670MM AT 1.75 M C/C WITH IRON BAR 16MM DIA AS HOLD FAST INCLUDING WELDING LINK WITH ANGLE FRAME AT 30CM C/C WITH NUTS AND BOLTS AND HORIZONTAL MS ANGLES AT TOP AND BOTTOM OF 25 X 25 X 5MM SIZE AND VERTICAL M.S. FLAT 35 X 5MM AND 25 X 5MM HORIZONTAL INCLUDING CROSS SUPPORT OF 40 X 40 X 6MM ANGLES BOTH SIDES AT EVERY CORNER OR BENDS EMBEDDED IN CONCRETE BLOCKS OF 1:4:8 OF SIZE 450 X 450 X 670MM INCLUDING 3 COATS OF OIL PAINTING ETC. COMP. (INO46-39, PGNO 298) (STATE SSR) ITEM SPEC. (AS DIRECTED BY ENGINEER IN CHARGE) |
| 82 | ITEM NO. 82: PROVIDING AND LAYING CAST IN SITU/ READY MIX CEMENT CONCRETE M-15 OF TRAP/ GRANITE/ QUARTZITE/ GNEISS METAL FOR COPING TO PLINTH OF PARAPET MOULDED OR CHAMFERED AS PER DRAWING OR AS DIRECTED INCLUDING STEEL CENTERING, PLYWOOD/ STEEL FORMWORK COMPACTING, ROUGHENING THEM IS SPECIAL FINISH IS TO BE PROVIDED, FINISHING UNEVEN AND HONEYCOMBED SURFACE AND CURING ETC. COMP. THE CEMENT MORTAR 1:3 PLASTER IS CONSIDERED FOR RENDERING UNEVEN AND HONEYCOMBED SURFACE ONLY, NEWLY LAID CONCRETE SHALL BE COVERED BY GUNNY BAG, PLASTIC, TARPAULIN ETC. (WOODEN CENTERING WILL NOT BE ALLOWED) WITH FINE AGGREGATE (CRUSHED SAND VSI GRADE FINELY WASHED ETC.) (INO24-16, PGNO 177) (STATE SSR) ITEM SPEC. (BD.E.3/PAGE NO. 288/ I.S. 456 (2000)) |
| 83 | ITEM NO. 83: PROVIDING AND FIXING 50MM DIA MEDIUM CLASS G.I. PIPE GATE WITH WICKET GATE OF APPROVED DRAWING WITH ALL FIXTURES & FITTINGS IN TWO LEAVES WITH STRONG HOLD FAST EMBEDDED IN C.C. BLOCK AT TOP & BOTTOM WITH LOCKING ARRANGEMENT INCLUDING CUTTING, BENDING, MAKING HOLES AND WITH ONE COAT OF PRIMER ETC. COMP. (INO23-05, PGNO 173) (STATE SSR) ITEM SPEC. (AS DIRECTED BY ENGINEER IN CHARGE) |
