|
| 1 | Supply, install, testing and commissioning of 16 Mtr motorised High mast shaft in two sections, internally and externally hot dip galvanised with average 70 microns, designed for 50M/Sec wind speed, comprising of raising and lowering system, 6mm dia stailess steel steel wire ropes 3 no for Lantern carriage and 2 no for winch, head frame, double drum winch with luminaire mounting arm, lanern carriage suitable to install 9 to 12 Nos luminaires in symmetrical arrangement, trailing cable, connector, integral power tool suitable for handling the total head load, , pully assembly, LED aviation obstruction light, lightning arrester spike including necessary RCC M-25 foundation as per manufacture\"s design complete all as specified and as directed by Engineer-in-Charge. Make : Crompton Cat part No. HM-1016P or equivalent in Philips, Wipro |
| 2 | Supply and fixing of LED flood light, 200W, watt 230 V, AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp and made up of pressure die cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP protction incl system efficincy >110/120LPW 10KV SPD included Energy saving, environmental friendly and general purpose lighting complete all as specified and directed Engineer-in-Charge. Make : Crompton Cat part No. LFLN-200-CDL/60-HPM or equivalent in Philips, Wipro |
| 3 | Supply and fix High Mast Panel outdoor type, suitable to take load up to 6 KW,Conforms to IS/IEC 60947-4-1,Provided with Protection Degree IP 54,Extended wide band (150 Vac - 300 Vac) coil, FRLS (Fire retardant low smoke) Internal wiring,In-built Short-Circuit Protection,Class H Insulation, 3 Phase 415 Volts AC with the following accessories:Phase : 3 Phase, 415 VoltsMax Load Capacity : 6 KWTimer type: AsronomicalContactor Rating : 32 A TPMCB Rating : 63 A TPNMake : Crompton/ Philips/Wipro |
| 4 | Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric cable, heavy duty, 1100 volt grade with stranded aluminium conductor cables of following sizes fixed in wall/ roof or laying in trenches etc., all as directed of 4 core 16 Sqmm complete all as specified and as directed.NOTE: Excavation, earth work shall be measured and paid for separately. |
| 5 | Excavation in trenches in soft/loose soil not exceeding 1.5 mtrwide and not exceeding 1.5 meter in depth for taking out and laying UG cable and getting out, excavated earth, forming bottomsurfaces to required level complete all as specified and directed. |
| 6 | Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soil complete all as specified and as directed. |
| 7 | Removing excavated soil and depositing to the sides and returning filling in including spreading leveling watering and well ramming in layers n.exc 25cm thick in soft/loose soil after cable is laid complete all as specified. |
| 8 | M&L for providing dry screened river sand as in sand cushioning to under groundcable including punning down of sand by layer complete all as specified and as directed. NOTE: Punned thickness shall be measured and paid. |
| 9 | Supply and lay unreinforced precast cable cover size 250X150X40 mm LV1 complete all as specified and as directed. |
| 10 | Earthing with Galvanized steel earth plate electrode of size 600mmX600mm, 6.00 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below the normal ground level with top edge of the plate not less than 1.5m below normal GL and connected to galvanized iron strip of size 32 x 6 mm size by means of bolts, nuts, check nuts and washers of galvanized ironsteel all as shown in Electrical Plate No.5 connecting to earthing test point, including necessary earth work in any type of soil, PCC earth chamber made in PCC 1:3:6 type C1 (using 20mm graded aggregate), common salt, charcoal, CI funnel, earth pit cover in RCC 1:2:4 type B1(using 20mm graded aggregates), with 8mm CTD bars @ 100mm c/c in both ways, including necessary form work complete including necessry test on completionincluding taking out old earthing all as specified and as directed. Note : The unit rate shall also include for excavation, earth work in hard/dense soil PCC (1:3:6) type C1 pit, RCC cover slab, GI funnel with 40 mm dia watering pipe, wire mesh, 15mm dia light grade GI protection pipe for earth lead etc., complete |
| 11 | Supply and installation of all in one solar street light with 17 watts, 3000 Lumens, 180 Lumens per watt built maintence free lithium ferro phosphate battery pack ( life- P04) with 21 AH capacity , 12 volts,35 watts solar panel module . The housing shall be made of single piece pressure die cast aluminium housing in non corrosive 500 hours NSS salt spray tested finish painting three step adjustable arm tilting option to adjust the light distribution with no additional pole support suitable for mounting on arm bracket directlyon pole top. MPPT charge controller and driver efficiency shall be greater than 90% including supply and installation of 7 metre octogonal pole made out of Hot- dip galvanization process as per IS 4759 1996. Bottom dia 130mm and top 70mm , 3mm thickness, base plate minimum 220mmx 220mm x 16mm thickness foundation bolts shall be M16 x700mm,including necessary RCC M-25 foundation and its earthwork as per manufacture\"s recommendations complete all as specified and as directed by Engineer-in-Charge.The bidder should submitt below documents along with sample of light for approval:-1) LM79 Report and virtual parameters test report from NABL Accredited Lab.2) Technical Data Sheet of Solar Street Light.3) Type Test Report of Solar Street Light.4) BIS Certificate of Battery.5) LM80 Report of LED Chip used in fixture.6) Data Sheet of LED Chip used in fixture. |
