|
| 1 | List of EquipmentItems |
| 2 | Temperature Measurement using Thermocouple & Thermistor & RTD Kit (with Suitable number of patch cards )SPECIFICATION1. POWER SUPPLY :12 V - 0-12V, 500mA to drive digital integral activity. 5V - 0-5V 250 mA to drive Analog to digital convertor. 2. DISPLAY: Seven segment LED to display output ( DPM ) Voltage value circuitry .3. INITIAL SET KNOB - Single turn potentiometer to set initial temperature ( Room temperature ). 4. FINAL SET KNOB : Single turn Potentiometer to calibrate the instrument ( Maximum temperature )5. 3 WAY ROTARY SWITCH :To select RTD , Thermocouple, Thermistor.6. SENSORS : i) Thermocouple ii) RTD ( PT 100 ) iii) Thermistor. |
| 3 | LVDT Trainer KitSPECIFICATION(with Suitable number of patch cards )1. DISPLAY : Seven segment LED to display output Voltage values( with polarity indicator ) ( DPM Circuitry )2. Single turn Potentiometer to calibrate the instrument. 3. To studycharacteristics behaviourof LVDT in positive and negative region with respect to voltage . 4. SENSITIVITY: 10 mV/mm 5. MICROMETER Measurement system.6. LVDT( i. TYPE:Linear displacement ii.CONFIGURATION : Axial type iii. LVDTFullstroke : +10mm rangeiv. ACTUAL Displacement --> Micrometer typev. Pitch 1mm. ) |
| 4 | Arduino UNO board with IC L293D with DC motor interfacing withoptical sensor setup to measure the speed of the DC motorkitSPECIFICATION1) Arduino UNO boardATmega328 microcontroller,Input voltage - 7-12V,14 Digital I/O Pins (6 PWM outputs),6 Analog Inputs,32k Flash Memory,16MHz Clock Speed , 2) DC motorDC motor interface with Arduino with L293D motor driver.Voltage : <100 V,Power : <50 W,Power Source : DC,Speed : 10001-14000 RPM,Motor Type : 775 Motor,3)L293D Motor driverWide Supply-Voltage Range: 4.5 V to 36 VOutput Current 0.6 A Per Channel.Pin compatible with L293D.4)Optical sensorUsing imported groove optical coupling sensor, width 5mm.If it covered, it will output high level; otherwise it output low level.The working voltage of 3.3V to 5 V.Output: digital switch output(0 and 1) |
| 5 | DC Dual Variable Power Supply UnitSPECIFICATIONRange 0-30v Variation: both fine and coarse with current and voltage variation through potentiometerDisplay: Seven segment LED display to display voltage |
| 6 | Arduino sheild Board kit Ultrasonic sensor, Inductive soil Moisture sensor, Servo motor,Potentiometer, ( with Suitable number of patch cards )SPECIFICATION1. ARDUINO SHIELD BOARD:Power supply: 5-12V, Motor controller : L 298P, Drives 2DC motor or 1 stepper motor, Max current : 2A per channel or 4A max ( with external power supply ) , Current sensing : 1.65 V/A.2. ULTRASONIC SENSOR: Power supply : 3.3-5V, Operating current : 8mA, Working frequency : 50 Hz, Ranging distance : 1cm-350cm, Resolution : 1cm,Measuring angle : 15degrees,Trigger Input Pulse width: 10uS.3. MOISTURE SENSOR:Voltage rating : 3.3-5V,Output Voltage- 3V,Opearing current - 5 mA, Temperature : 0 degreeC to 40 degree C, Accuracy : ± ( 0.5 % n+1 )4.SERVO MOTOR:Operating Voltage : 5V, Torque : 2.5 Kg/cm, Operating speed : 0.1s / 60 degree C5.POTENTIOMETER: Resistance : 0-2 KΩ |
| 7 | Interfacing push button , SPST, SPDT, Limit switch with 12 V DC motor kitSPECIFICATION( with Suitable number of patch cards )1. Push button type ( to drive 12 V DC motor.i. Normally open- each oneii . Normally closed - each one) 2. SPST- On -Off toggle switch( to drive 12 V DC motor ) 3. SPDT- On -Off toggle switch to driveLoad 1 - 12 V DC motor1 to drive Load 2 - 12 V DC motor2 4. LIMIT SWITCH- to drive 12 V DC motor 5. 12 VDC Motor - 2 Power supply.- 12 V DC , 500 mA to drive DC motors |
| 8 | Interfacing Transistor and relay with 12 V DC motor kit( with Suitable number of patch cards )SPECIFICATION1. Transistor - BJT(BC 107 )2.Relay :i. NO (Normally Open )ii. NC (Normally Closed ) Coil Voltage rating- 12 V DC Swiching circuitVoltage & Current rating- 12V DC , 500 mA3. 12 V DC motor- 2 Power supply 12V DC , 500 mA to drive DC motors |
| 9 | 3 PhaseInductionMotor,ForwardReverseControlswitchand Clamp Meter (with suitable no of patch cards)SPECIFICATIONOne HP- 3 Phase Squirrel cage Induction motor |
| 10 | 440V , 10 A 3 Phase DOL STARTER KIT with Forward / Reverse control switch 1. 3⌀ DOL Starter(To drive 3⌀ Squirrel cage Induction motor) 2. I/P 3 phase connectivity pins 3. O/P 3 phaseconnectivity pins4. Forward / Reverse control switch 3 Phase AC DOL Starter kit with Forward / Reverse Control switch test kit ( with Suitable number of patch cards ) - |
| 11 | Clampmeter -(TONGUE TESTER ) |
