Tender For Modernization Work - OD7725/2024-2025:L-Shaped Workstation cum file storage (1800mm x 600 mm) + (1200mm x 450mm) : Providing and fixing L- Shaped Workstation as per following specifications : Modular Partition: 56 mm thickness modular partition frame work made out of 56 Aluminum partition panel minimum thickness of 1.5 mm powder coated 50 microns frame work designed to carry out electrical power and computer wiring in 2 different race ways with a separation of at least 300mm between them including necessary slots. The frame work consists of minimum two vertical upright a top horizontal section, bottom section and intermediate sections (minimum 40 mm x 30 mm) The frame structure covering and Top trim / side trim made out of Aluminum with powder coating (50 microns). All Aluminum Horizontal and vertical sections are extruded from AA 6063 American standard alloy with 12 HRC hardness of Architectural grade (IS 10259:1982) of 18 gauge minimum. The thicknesses of extruded sections vary based on its design and its point load bearing design engineering. The skinning / panels / tiles to be of 9mm thick Prelaminated particle Board (Grade II and Type-II, IS 12823: 1990; Reaffirmed 2005) till 1200mm height from the floor level for outside facia. Inside facia fabric panel with soft board with minimum 9mm thickness above table top (450 mm height). 9mm thick Prelaminated particle board panel finished with 0.8mm thick laminate from floor level to top of table top (750 mm height). The edges to be capped (as per approved design and drawing) Aluminum end trim with powder coating. Cost to include that for provision of fixing switches and the necessary cut out for the same. The height of the partition to be 1200mm. As per drawing and direction complete with all standard fittings and fixtures, leveling screws etc. Cost to include the supporting system to partitions and walls such as brackets / fasteners / joining posts / aluminum race ways 2 nos / wire management cleats / runners etc. 2 OD7723/2024-2025:L-Shaped Workstation cum file storage (1800mm x 600 mm) + (1200mm x 450mm) : Providing and fixing L- Shaped Workstation as per following specifications : Table Top: Providing and installing 600mm deep Table top made of 25mm thick pre laminated particle board Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8 mm thick laminate, all exposed edges finished with 2mm x 25mm PVC hot pressed lipping of approved profile, all of approved shade and colour. Rates are inclusive of fixing to the partition with necessary powder coated heavy duty MS brackets, cleats etc. for supporting table tops and rates shall include that for 1 nos. matching to top, ABS wire manager (standard size) per work station, complete as per drawings and direction. 3 OD7722/2024-2025:L-Shaped Workstation cum file storage (1800mm x 600 mm) + (1200mm x 450mm) : Providing and fixing L- Shaped Workstation as per following specifications : Pedestal: Providing and installing drawer boxes of size 585mm ht., 390mm width and 500mm deep, top made out of 18mm thick pre laminated particle board Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8mm thick laminate, front and sides made of 18mm thick pre laminated particle board Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005)finished in 0.8mm thick laminate and back, drawer bottom to be 6mm thick particle board with.08mm thick laminate. 2 nos. minimum 120mm high drawer and 1 minimum 275mm high filing drawer with 4 nos. Nylon Spacers 10mm ht. with single key lock mechanism / SS telescopic channels and provided with handle and necessary fixtures (heavy duty high performance) as directed. 4 OD7719/2024-2025:L-Shaped Workstation cum file storage (1800mm x 600 mm) + (1200mm x 450mm) : Providing and fixing L- Shaped Workstation as per following specifications : File storage: Providing and installing 370mm deep and 1200mm height File racks made of 1.25” aluminum powder coated section and covered with PVC laminated sheet 3mm with approved color. 5 OD7718/2024-2025:Clerical tables size 1200x600x750mm: Providing and installing 600mm deep and 1200mm length Table of size made of 25mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) and legs and bottom made out of 17mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8 mm thick laminate, Top edges finished with 2mm x 25mm PVC hot pressed lipping on approved profile, other exposed edges finished with 2mm x 17mm PVC hot pressed lipping of approved profile, all of approved shade and colour. Table having one drawer, cupboard, and pullout and CPU trolley. 6 OD7717/2024-2025:Drivers tables size 900x600x750mm: Providing and installing 600mm deep and 900mm length Table of size made of 25mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) and legs and bottom made out of 17mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8 mm thick laminate, Top edges finished with 2mm x 25mm PVC hot pressed lipping on approved profile. Other exposed, edges finished with 2mm x 17mm PVC hot pressed lipping all of approved shade and colour. Table having single drawer. 7 OD7716/2024-2025:‘L’ shaped Executive table of size 1500x750x750mm. 900x450x750mm : Providing and installing 750mm deep and 1500mm length made of 25mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) and legs and bottom made out of 17mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8 mm thick laminate, Top edges finished with 2mm x 25mm PVC hot pressed lipping and other exposed edges finished with 2mm x 17mm PVC hot pressed of approved profile, all of approved shade and color. Table having one side brawer box, pullout and CPU trolley. Side table having 2 doors with shelf. 8 OD7715/2024-2025:L’ shaped Executive table of size 1800x750x750mm. 900x450x750mm : Providing and installing 750mm deep and 1500mm length made of 25mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) and legs and bottom made out of 17mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8 mm thick laminate, Top edges finished with 2mm x 25mm PVC hot pressed lipping and other exposed edges finished with 2mm x 17mm PVC hot pressed of approved profile, all of approved shade and color. Table having one side brawer box, pullout and CPU trolley. Side table having 2 doors with shelf. 9 OD7714/2024-2025:Providing and supplying a Low back chair with ergonomic design, comfortable and aesthetically appealing. The seat shall be made of 12mm thick hot pressed commercial plywood padded with high resilience molded polyurethane foam having density 48kg/m³ in seat and having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 0.8mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine which helps to provide back support. The chair shall be supplied with polypropylene arm. 10 OD7713/2024-2025:Providing and supplying medium back revolving chair with ergonomic design, comfortable and aesthetically appealing. The seat shall be made of 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam having density 48kg/m³ in seat and having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 0.8mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine which helps to provide back support. The chair shall be supplied with polypropylene arm. 11 OD7712/2024-2025:Providing and supplying medium back Visitors chair with ergonomic design, comfortable and aesthetically appealing. The seat shall be made of 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam having density 48kg/m³ in seat and having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 0.8mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine which helps to provide back support. Frame structures using 1” round tubular with powder coated. The chair shall be supplied with polypropylene arm. 12 OD7711/2024-2025:Providing and fixing Cabin with door: Frame structure Made with 17mm 710 grade marine quality plywood(Green/century), two side covered with 9mm 710grade ply with Mica lamination. Cabin having 8mm glass with hatching sticker for windows and doors. With approved design. 13 OD7710/2024-2025:Reception table of size 1.40x60x80cm made with of 25mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) and legs and bottom made out of 17mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8 mm thick laminate, Top edges finished with 2mm x 25mm PVC hot pressed lipping on approved profile, other exposed edges finished with 2mm x 17mm PVC hot pressed lipping of approved profile, all of approved shade and color. Table having one drawer, cupboard, and pullout and CPU shelf. 14 OD7709/2024-2025:Back side paneling for Reception area Frame structure Made with 17mm 710grade marine quality plywood (Green/century), two sides covered with 9mm 710grade ply with Mica lamination. Front side panel having emblem with letter made of acrylic with golden colour letters. 15 OD7708/2024-2025:L’ shaped Executive table (for EE) of size 1800x750x750mm. 1200x450x750mm : Providing and installing 750mm deep and 1500mm length made of 25mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) and legs and bottom made out of 17mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8 mm thick laminate, Top edges finished with 2mm x 25mm PVC hot pressed lipping and other exposed edges finished with 2mm x 17mm PVC hot pressed of approved profile, all of approved shade and color. Table having one side brawer box, pullout and CPU trolley. Side table having 2 doors with shelf. 16 OD7707/2024-2025:Executive chair High back for EE - Ergonomic design, comfortable and aesthetically appealing. The seat shall be made of 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam having density 48kg/m³ in seat and having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 0.8mm thick and 300 GSM. Back of the chair having design with artificial leather as per approved design. 17 OD7706/2024-2025:Conference table of size 2.8L x 0.75W x 0.75H : Providing Conference table of 25mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) and legs and bottom made out of 17mm thick pre laminated particle board Top Grade II and Type-II (IS 12823: 1990; Reaffirmed 2005) finished with 0.8 mm thick laminate, Top edges finished with 2mm x 25mm PVC hot pressed lipping on approved profile, other exposed edges finished with 2mm x 17mm PVC hot pressed lipping of approved profile, all of approved shade and colours. 18 OD7705/2024-2025:Meeting room chair fabric upholstered netted chair : The seat shall be made of 12mm thick hot pressed commercial plywood padded with high resilience molded polyurethane foam having density 48kg/m³ in seat and having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 0.8mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ ABS mounded cover and the backrest shall be made by keeping the natural curvature of the spine which helps to provide back support. Frame structures using 1” round tubular with powder coated. The chair shall be supplied with polypropylene arm. 19 OD7741/2024-2025:Airport chair 3 seater 20 OD7721/2024-2025:Keyboard tray
