|
| 1 | Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness includingall labour, hire charges of all machineries etc., complete.in area of Light Jungle-By Mechanical means using Dozer and as directed by Engineer in charge of the work. |
| 2 | Tack Coat on Bituminous surfaces Providing and applying tack coat with bitumen emulsion (RS1) using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom & dusting by air compressor and spraying includingcost of allmaterials, labour, usage charges of all machinery,lead,lift, loading & unloading etc., complete, including lead for emulsion and as directed by Engineer in charge of the work. |
| 3 | Dense Graded Bituminous Macadam Grading-IIProviding and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates as per table 500-7 of specified grading premixed with bituminous binder VG-30 paving bitumen as per clause 504.3.1 complying with IS-73-2013 of specified grading, premixed with bituminous binder at 4.5 percent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects including cost of all materialsall labour, usage charges of all machinery all lead, lifts, loading, unloading stacking transporting etc., complete, including lead for bitumen, lead of mixed material , excluding cost of primer/ tack coat - 50 mm compacted thickness Grading -IIusing Bitumen 60/70 Grade(VG-30) and as directed by Engineer in charge of the work. |
| 4 | Bituminous Concrete - Grading IIProviding and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates as per table 500-7 of specified grading premixed with bituminous binder VG-30 paving bitumen as per clause 504.3.1 complying with IS-73-2013 of specified grading, premixed with bituminous binder at 5.4 per cent of mix and filler at 2% by weight of agregate, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects including cost of all materialsall labour, usage charges of all machinery all lead, lifts, loading, unloading stacking transporting etc., complete, includingt lead for bitumen,lead of mixed material, excluding cost of primer/ tack coat- 30mm compacted thickness Grading -II and as directed by Engineer in charge of the work. |
| 5 | Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 laid in layers not exceeding 250 mm thick and compacting it by mechanical means after adding water to its OMC, so as to achieve 97% compaction ofmaximum dry density and finish the surface to the required camber, grade and cross section etc., speading, grading by motor grador,consolidation by rollerincluding all lead, lifts, loading, unloading, all labour, usage charges of machinery etc., complete. (New road formation)and as directed by Engineer in charge of the work. |
| 6 | Surface Drains in Soil(New),Construction of unlined surface drains of average cross sectional area 0.40 m2 in soil to specified lines, grades, levels and dimensions to the requirement of clause301 and 309. Excavated material to be used in embankment within a lead of 1000 meters including all labour ,load ,unload, usage charges of all machinery etc,complete ,Mechanical Means and as directed by Engineer in charge of the work. |
| 7 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes, including, barricading, traffic diversion as per IRC-35, cleaning the surface of dirt, dust and other foriegn matter, demarcation at site, traffuc control,cost of all materialsall labour, lead, lifts, loading, unloading transporting etc., complete of 2.5 mm thick and as directed by Engineer in charge of the work. |
| 8 | Supplying of Solar Raised Pavement Markers made of polycarbonate molded body with circular shape, solar powered,LED self illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The marker shall support a load of 20000 kg tested in accordance to ASTM D 4280. The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0 C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinking is 1 Hz. There should be current losses of less than 20 microamperes at 2.4 V in sleepcharging mode to enhance the life of the marker and a full charge should provide for a minimum autonomy of 50 hours. The height, width and length of the marker shall not be less than 10 mm x 100 mm x 100 mm. Also, the surface diameter of the marker shall not be less than 100 mm respectively. The weight of the marker shall not exceed 0.5 Kilograms. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the engineer, including cost of all materialsall labour, lead, lifts, loading, unloading transporting etc., complete and as directed by Engineer in charge of the work. |
| 9 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of Class-C Type XI retro reflective sheeting fixed over 2 mm thick aluminium sheeting vide clause 801.3, 4mm thick Aluminium composite material sheet including lettering depending on the size of the sign fixed over back support frame of min 25 x 25 x 3mm Angle mounted on a mild steel circular pipe 65 NB 3.60mtrs high (min effective height 1.90 mtrs),3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67,including curing, cost of all materialsall labour, lead, lifts, loading, unloading transporting etc., complete and as directed by Engineer in charge of the work.B.ii 90 cm equilateral triangle |
| 10 | B.iv 60 cm equilateral triangle |
| 11 | B.viii 60 cm circular |
| 12 | B.xi 60 cm X 50 cm Rectangular |
| 13 | Providing and erecting direction and place identification retro-reflectorised sign as per IRC :67 made of High Intensity grade sheeting lause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminum composite material sheet with overall thickness of 4 mm with area exceeding 0.9 sqm fixed over back support frame of min 40 x 40 x 5 mm MS Angle mounted on two nos. of mild steel circular pipe 65 NB, 3.2 mm thicknness and 4.5 meter total height firmly fixed to the ground by means of properly designed foundation with M 25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing, including curing, cost of all materialsall labour, lead, lifts, loading, unloading transporting etc., complete and as directed by Engineer in charge of the work. |
| 14 | Providing and erecting Project Display Board of size 1.80 verticalx1.60M Horizontal made of Cold Rolled Coil Sheet 16 Guage (1.6mm thickness) sheeting sthrenghtened by welding to MS angle of size 35x35x5mm iron framework on all sides, extra cross vertical angle fixed using nuts and bolts, base of the board shall be cleaned, applying red oxide and black paint by sprayer on both sides of the board and all MS iron frameworks, background of the facing side of the board painted in traffic yellow, project information written in English/Kannada/Hindi, painting letters and numerals in black, fixed on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level and the board 2.8M from ground level as per approved drawing (Excluding cost of lettering)including cost of all materialsall labour, lead, lifts, loading, unloading transporting etc., complete and as directed by Engineer in charge of the work. |
| 15 | Reinforced cement concrete M15 Grade kilometer stone of standard design as per irc :8, fixing in position includingpainting and printing letters etc., including cost of all materials all labour, lead, lifts, loading, usage charges of machinery, unloading transporting etc, complete and as directed by Engineer in charge of the work.a)Ordinary kilometer stone (precast) |
| 16 | 200 meter stone ( precast) |
