|
| 1 | Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land. Note: The place of disposal shall be find out by the contractor. |
| 2 | Material & labour for rendering 20 mm thick pre polymer modified ready mixed cement based plasterin two coats 12 mm thick base coat and 8 mm thick finishing/final coat.Polymer modified ready mixed cement based plaster should having minimum composition of cement & sand 1:4 using fully treated dry, well graded naturalsand conforming to IS-383 suitable for external wall plastering having low rebound properties, low water demand for curing properties, mechnical mixing with water in a matalic tray only to made good, consistency as per manufacturers specification including using richer mix for making corners and making grooves of existing size including twolegged MS pipe scaffolding complete all as specified and directed. |
| 3 | Supply only integral water proofing compound. |
| 4 | Material & labour for preparing surfaces using wire brush to remove any loose paint, dust, bitumen or grease and cleaning with high pressure water jet, check the surface for its soundness using small hammer, all cracks shall be filled with crack seal/ polymer modified cement mortar andapplying damp proof smart care waterproof coating to wall and floor surfaces complete all as per manufactures instructions through approved applicator including necessary scaffolding and safety arrangement for high rise building complete all as directed. |
| 5 | Material & labour for preparation of new plastered surfaces of wall, soffits, facia roof and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqmcomplete all as per manufactures instructions through approved applicator including necessary scaffolding and safety arrangement for high rise building complete all as directed. |
| 6 | Demolition of brick work or stone/boulder masonry, built in cement mortar, including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work & precast concrete articles including copings etc.and removing debris outside MD land complete all as specified.Note: The place of disposal shall be find out by the contractor. |
| 7 | Material & labour for brick work with sub class \"B\" bricks old size, straight or curved on plan exc 6m mean radius in cement mortar 1:4 complete all as specified. |
| 8 | Material & labour for brick work with sub class \"B\" bricks (old Size) straight or curved on plan exc 6 m mean radius and built in CM (1:4) in half brick thick wallcomplete all as specified. |
| 9 | Taking down chowkats with shutters (without taking off shutters from the frames) area n.exc 1.5 Sqm each |
| 10 | Supply & Fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specification and drawings shown in SSR Part II complete all as specified and as directed by Engr-in-Charge. |
| 11 | Supply & fixing 30 mm thick factory made solid panel PVC door shutter (Style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame as per specification and drawings shown in SSR Part II complete all as specified and as directed by Engr-in-Charge. |
| 12 | Supply & fixing aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, 300 mm long , ISI marked. |
| 13 | Supply & fixing aluminium anodised barrel tower bolts of extruded section, 200 mm length, ISI marked. |
| 14 | Supply & fixing extruded aluminium alloy handles, fabricated type, anodised 150 mm size, ISI marked. |
| 15 | Supply & fixing 100 mm long stainless steelbutt hinges medium weight with stainless steel hinge pin, bright finished. |
| 16 | Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal of debris out of MD land complete all as specified.Note: The place of disposal shall be find out by the contractor. |
| 17 | Material & labour for providing cement concrete type B1 1:2:4 (20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed blocks for holding hold fasts, bed plates, kerbs not provided, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified. |
| 18 | Dismantling plain or corrugated steel sheeting, any gauge or thickness incl Nainital or similar pattern roof coverings complete all as specified and directed. |
| 19 | S&F pre-painted hot- dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.5 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor for height of building exceeding 10 metres but not exceeding 20 metres complete all as specified and as directed. |
| 20 | S&F pre-painted hot- dip aluminium-zinc alloy metallic coated plain steel sheet, corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.5 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor for height of building exceeding 10 metres but not exceeding 20 metres complete all as specified and as directed. |
| 21 | Material & Labour for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410 -W (GdeE- 250) quality A complete all as specified and directed. |
| 22 | Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar including removal of rubbish out side MD land.Note: The place of disposal shall be find out by the contractor. |
| 23 | Material & labour 20 mm thick machine cut machine polished Granite slab (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like laid over and including 20 mm thick screed bed in cement mortar (1:4), set and jointed in neat cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match withshade of granite complete all as specified and as directed |
| 24 | Rounding to edges of stone slabs on edge, such as in steps, cooking platform and making grooves for lining and other similar work complete all as specified and directed. |
| 25 | Material & labour for PCC 1:3:6 type C2 using (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified. |
| 26 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified. |
| 27 | Material & labour for false ceiling work of aluminium anodized ceiling grid system of grid size 605mm x 605mm made out of aluminium anodised main and cross tee of size15mm x 15mm x 1.5mm thick, weighing 0.12 Kg per running metrejointed at junction/crossings with anodized aluminium angle bracket and cross tees shall be of size 40mm x 25mm x 2mm thick , weighing 0.36 Kg per running metre conforming to IS 733, IS 737 and IS 1285 fixed with sutiable mild steel, bolts nuts and washers, all as per manufacturer’s instructions complete all as specified and directed by Engineer-in-Charge.Note- PVC protected sheeting shall be used to avoid scratches, damage to the framework while fixing to ceiling. |
| 28 | Supply & fixing Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 29 | Supply & fixing 4mm thick designed non asbestos fibre cement building boards of size 600mm x 600mm fixed or laid/inserted in aluminium grid false ceiling complete all as specified. |
| 30 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing debris outside MD land complete all as specified. Note: The place of disposal shall be find out by the contractor. |
| 31 | Material & Labour for Non skid coloured ceramic tiles 7 to 8 mm thick (square/Rectanglar) area of each tiles exc 0.06 Sqm but n exc 0.09 Sqm laid in floor over and including20mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified. |
| 32 | Material & Labour for light shade vitrified ceramic tiles 10 mm thick (square /rectangular ) polished area of each tiles not exceeding 0.36 sqm, in floor laid in floor over and including15mm thick screed bed in cement mortar ( (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified. |
| 33 | Material & Labour light shade vitrified ceramic tiles 10 mm thick (square /rectangular ) polished, area of each tiles not exceeding 0.36 Sqm , as in vertical surfaces such as skirting(100mm hight) /dado etc., laid over and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement paste and pointed in white or coloured cement to match the shade of tile complete all as specified. |
| 34 | Material & Labour for coloured glazed ceramic tiles 450mm x 300mm x 7mm thick but laid on vertical surfaces such as skirting(100mm hight) /dado etc., laid over and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement paste and pointed in white or coloured cement to match the shade of tile complete all as specified. |
| 35 | Supply & Fixing in repairs 160 mm bore PVC ( SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls with dash through fastners and rain water bracketsuitable for 110mm bore pipe spacing 1.5m c/c as per CE (Navy) Mumbai TD No TD/2023/01 or laid in floor complete all as specified. |
| 36 | Supply & fixing for PVC (SWR) bends any radius 160 mm bore fixed with rubber ring joints.complete all as specified. |
| 37 | Supply & Fixing 110mm bore PVC ( SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls with dash through fastners and rain water bracketsuitable for 110mm bore pipe spacing 1.5m c/c as per CE (Navy) Mumbai TD No TD/2023/01 or laid in floor complete all as specified. |
| 38 | -Ditto- all as sper item No 37.00 above but 75 mm bore |
| 39 | Supply & fixing PVC (SWR) bends 110 mm fixed with rubber ring joints.complete all as specified. |
| 40 | Supply & fixing PVC (SWR) bends 75 mm fixed with rubber ring joints.complete all as specified. |
| 41 | Supply & fixing PVC (SWR) branch piece 110 mm single Y fixed with rubber ring joints.complete all as specified. |
| 42 | Supply & fixing PVC (SWR) branch piece 75 mm single Y fixed with rubber ring joints.complete all as specified. |
| 43 | Supply & fixing PVC (SWR) junction single (single tee) equal or unequal piece 110 mm fixed with rubber ring joints.complete all as specified. |
| 44 | Supply & fixing PVC (SWR) junction single (single tee) equal or unequal piece 75 mm fixed with rubber ring joints.complete all as specified. |
| 45 | Supply & fixing PVC (SWR) vent cowl 110 mm fixed with rubber ring joints.complete all as specified. |
| 46 | Supply & fixing PVC (SWR) vent cowl 75 mm fixed with rubber ring joints.complete all as specified. |
| 47 | Material & labour in repairsPVC (SWR) floor trap, plain with grating including jointing with solvent cement, diameter of outlet 75 mm. |
| 48 | Supply & fixing in repairs wall hung WC of size 370mm x 490mm x 365mm including UF Soft close slim seat cover hinges, fixing accessories completeincluding S trap-300mm,connecting piece and making all connections complete all as specified and directed by Engr-in-Charge . |
| 49 | Supply & fixing in repairs single piece WC with UF Soft close slim seat cover, fixing accessories set and cistern andfitting including S trap-300mm,connecting piece and making all connections complete all as specified and directed by Engr-in-Charge . |
| 50 | Supply & fixing in repairs 32 mm dia Flush pipe of Polyethylene of low or high density or PVC for low level flushing cistern |
| 51 | Taking up or down steel tubing and connections including cleaning and refixing in new or old position (walls, ceilings, floors etc) 100 mm bore pipes including providing suitable size GI clamps and fittings. |
| 52 | Taking up or down existing 15 mm bore GI water tubing complete with all fittings. |
| 53 | Taking up or down existing 20 mm bore GI water tubing complete with all fittings. |
| 54 | Taking up or down existing25 mm bore GI water tubing complete with all fittings. |
| 55 | Taking up or down existing 50 mm bore GI water tubing complete with all fittings. |
| 56 | Supply & fixing 50 mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 including all fittings such as ends, elbows, unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc.and fixed to walls, celing with suitable size saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves or laid in floors complete all as specified. |
| 57 | -Ditto- all as per item No 56.00 above but 25 mm bore |
| 58 | Supply & fixing 15 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified. |
| 59 | Supply & fixing 20mm bore GI tubing medium grade with all fittings like Tee, bend, elbow etc fixed to walls or ceilings with saddles/spacers complete all as specified and directed by Engineer-in-Charge. |
| 60 | Material & labour for rendering 20mm thick in two coats (15mm inner coat + 5mm finishing coat) on fair faces of brick work or concrete surfacesin cement mortar 1:4 mixed with integral water proofing compound @ 3% by weight of cementand finished fair and even including necessary scaffolding and safety arrangementfor high rise bldgs complete all as specified and directed by Engr-in-Charge.Note- Water proofing compoundshall be measured and paid for separately. |
| 61 | Material & labour for rendering 5 mm thick on fair faces of concrete surfaces in ceiling in cement mortar (1:3) and finished even and smooth without using extra cement complete all as specified. |
| 62 | Material & labour for preparing surfaces and applying 4mm thick texture finished plastering in CM 1:2 (Mix one part of white cement & two parts of Dholpuri clear quarts powder of 1 to 2 mm grading) with the help of hand driven machine with suitable painting to achieve stone masonary pattern or approved design and provide flush pointing with white boarder line including necessary scaffolding and safety measures to carrying out works upto triple stories Bldg complete all as per manufactures instructions ans as directed. |
| 63 | Supply & fixing 3 mm thick aluminium composite panel (Russian stone pattern or approved colour/shade)forwall cladding, beam and ceiling in circular/ rectangular or shape as per site requirment including cutting, notching, bending to shape as required jointing with silicon gel of approved colour & aluminum tubular hallow section 25 x 25 mm not exceeding 900 mm C/C on exceeding column/beam/slab to hold APC cladding complete all as per manufactures instructions ans as directed. |
| 64 | Material & labour for preparing new plastered surfaces of wall,applying one coat ofwall care putty not less than 2mm thickness and makingthe surface even and smooth using emery paperand applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified. |
| 65 | Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified. |
| 66 | Supply & fixing mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; walkj ways, railings, frame work for water tanks and similar work conforming to Fe 290 Gd E-165 all as specified . |
| 67 | Supply & fixing steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS -1161 1979 grade St-240 |
| 68 | Material & labour for rolled mild steel in framed work as in door or gate of angle or other section with gusset plates, rails, braces etc complete,drilled for fixing of steel sheeting or other covering. Doors/gates to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings( exclusive of steel sheating or other covering,running rails and guides) and hanging also fastening and fixing complete conforming to Fe-410-0 or Fe 310-0. |
| 69 | Material & labour for preparing new steel surfaces of any description n.exc 10 cm in width or girth when unconnected with other painting or and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer. |
| 70 | Material & labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) and finished even & smooth without using extra cement completed all as specified. |
| 71 | Material & labour for rendering 10 mm thick on fair faces of concrete surfaces in ceiling in CM (1:3) and finished even and smooth without using extra cement completed all as specified. |
| 72 | Material & labour for preparation of new plasteredsurface of ceiling and applying two coats of oil emulsion distemper over a coat of alkali resistant primer complete all as specified. |
| 73 | Material & labour for preparation of old decorated surfaces of wall and applying one coat of oil emulsion distemper complete all as specified and directed. |
| 74 | Material & labour for preparation of old decorated surfaces of ceiling and applying one coat of oil emulsion distemper complete all as specified and directed. |
| 75 | Material & labour for preparing old decorated surfaces of wall, soffits, facia roof and applying one coat of weather proof acrylic exterior paint (100% Acrylic) including necessary scaffolding and safety arrangement complete all as specified. |
| 76 | Material & labour for PCC 1:3:6 type C2 using (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified. |
| 77 | Material & labour for machine pressed precast concrete inter locking paver block any shape and size with grey cement and pigment conforming to IS-15658-2006 of 60mm thickness M-35 Grade, glossy finished of approved colour laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints and gently rolled with vibrator complete all as specified . |
| 78 | Material and Labour for machine pressedchequered cement coloured tiles of size 300mm x 300mm x 20mm thickmixed with grey cement and pigmentlaid over and including 15mm thick screed bed in CM 1:4set and jointed and pointed inneat cement slurry in floors including cut and polished as specified in SSR Part I complete all as specified and directed by Engineer -in-Charge. |
| 79 | Demolition of Stone sett paving of any description or thickness laid dry or laid dry and pointedand removing debris outside MD land complete all as specified. Note: The place of disposal shall be find out by the contractor. |
| 80 | Material & labour for hardcore of broken stone or boulders of gauge n. exc 63mm, deposited, spread and leveled in layers n. exc 15cm thick watered and rammed to true surface complete all as specified. |
| 81 | Material & labour for hardcore of broken stone or boulders of gauge exc 63mm, deposited, spread and leveled in layers n. exc 15cm thick watered and rammed to true surface complete all as specified. |
| 82 | Material & labour for TMT CRS bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with the clips complete all as specified . |
| 83 | Material & labour for Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. Note-Where RCC/PCC band in walls, spanning and opening, the formwork soffit only shall be paid seperately |
| 84 | Material & labour for use and waste of form work for sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves includingsupports overhangs, etc also splays between floors and beams etc for rough finished surface of concrete flat complete all as specified. |
| 85 | Material & labour for RCC ready mix concrete (design mix) RMC M-35 grade for foundation, including raft footings, foundation beams, plinth beams, bases for column etc., basement slabs, under reamed piles and mass concrete, slabs complete all as specified . |
| 86 | Material & labour for finishing surface of concrete roads, pavements, by belting complete all as specified and as directed by Engineer-in-Charge. |
| 87 | Material & labour for forming 12 mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A\",thickness of concrete slab 100 mm complete all as specified and as directed. |
| 88 | Material & labour for forming contraction (Dummy) joints 65mm deep x 10mm wide filled with pre-formed bituminous filler sealing compound, Grade ‘A\" complete all as specified and as directed. |
| 89 | Material & labour for Stone kerb of roughly squared stones (Granite or trap sand ) stone of size 20cm x 30cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar (1:6) and struck flush. |
| 90 | Material & labour for machine cut, machine polishedgranite stone slab 18-20mm thick in flooring set, bedded and jointed with white cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite stone laid over and including screed bed or bedding layer of 15 mm thick in cement mortar (1:4) complete all as specified . |
| 91 | Material & labour for machine cut, machine polishedgranite stone slab 18-20mm thickin skirting/dado set, bedded and jointed with white cement paste and pointed with white cement mixed with admixture of pigment to match the shade of granite stone laid over and including backing coat 10 mm thick on fair faces of brick or concrete surface in cement mortar (1:3) complete all as specified. |
| 92 | Supply andfixing inrepairs304 grade stainless steel decorative railing made of hollow tubes, channels, plates etc including welding, grinding, buffing, polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc of required size, on the top of floor or the side of waiste slab with suitable arrangement complete all as specified and as directed Engr-in-charge. |
| 93 | Material & labour as fixed in repair Stainless steel decorative chain of grade 304 having 8mm minimum thickness (design and pattern as approved by GE) used to connect two stainless steel postwith hooks etc. complete with and including necessary welding, buffing/ polishing and fixing complete all as specified and directed. |
| 94 | Demolition of stone / boulder masonry laid dry by hand or by mechanical and removing debris outside MD land complete all as specified .Note: The place of disposal shall be find out by the contractor. |
| 95 | Material & labour for demolition of existing roof treatment laid in lime concrete/china mosaic, any thickness including brick tiles etc. cleaning of RCC roof slab with wire brushing, washing out with water and finally remove dirt using air jet and removal of debries out of MD land complete all as specified and directed by Engineer-in-Charge. |
| 96 | Demolition of Cement concrete (unreinforced) of Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removal of debris out of MD land complete all as specified.Note: The place of disposal shall be find out by the contractor. |
| 97 | Material & Labour for PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as a leveling course / padding on RCC roof/ chajja top surfaces, laid to slope and finished fair and even complete all as specified. |
| 98 | Material & labour for apply bituminous oil based cold applied primer @ 270 to 300 gms/Sqm manufactured by the same agency as that of APP all as per manufacturers instructions and laying 5 layered water proofing treatment comprising of 3 mm thick APP ( A woollen propylene) modified membrane reinforced with 180 GSM (Gms/Sqm) of non woven polyester mat, applied by thermo fusion using LPG torch on the bottom protion of the membrane with an overlap of 100mm in both direction & Aluminium paint over it complete all as specified and directed. Note:-Company authorised applicator allowed only permissible to the concerned site). |
| 99 | Material & labour for burshing neat cement slurry with 3 Kg of cement per square meter complete all as specified and directed. |
| 100 | Material & labour for rendering 20mm thick in CM (1:4) mixed with WPC @ 3% by weight of cement on roof top surface finished even and faircomplete all as specified and as directed.Note : WPC will be measuerd and paid separately. |
| 101 | Material & labour for cement concrete tiles 250 mm x 250 mm x 22 mm thick, with grey cement and no pigment, machine pressed; set, jointed and pointed in neat cement slurry laid over and including 15 mm thick screed bed or bedding layer in cm (1:3) over water proofing treatment complete all as specifiedand directed |
| 102 | Material & labour for 25mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified. |
| 103 | Disconnection existing tanks, setting aside (or lowering if required) for cleaning etc and hoisting and reconnecting and re-fixing in the sameposition capacity exc 1000 Ltr and n.exc 10000 Ltrcomplete all as specified. |
| 104 | Taking down 25 mm bore, GI tubing including all connectionscomplete all as specified. |
| 105 | Taking down 40 mm bore, GI tubing including all connectionscomplete all as specified. |
| 106 | Supply & fixing 25 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings or laid in floors with suitable size GI clamps complete all as specified. |
| 107 | -Ditto- all as per item No 106.00 above but 40mm bore. |
| 108 | Material & labour for rendering 15 mm thick on fair faces of brickwork or concrete surfaces in CM (1:4) and finished fair and even complete all as specified. |
