|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete. |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. |
| 6 | Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 7 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). |
| 8 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 9 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 10 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). |
| 11 | 12 mm cement plaster of mix :1:4 (1 cement : 4 coarse sand) |
| 12 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 13 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 14 | Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. White sand stone |
| 15 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : Red sand stone - exposed face fine dressed with rough backing.30 mm thick |
| 16 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. |
| 17 | Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. |
| 18 | Steel work in built up tubular ( round , squre orrectanguler hollow tubes etc.) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approvedsteel primer , including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. |
| 19 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 20 | 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. * Red sand stone |
| 21 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 22 | Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge. |
| 23 | P/F of 4050 mm dia granite polished spheres with base plate of granite |
| 24 | Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign material etc. and lining out complete.New work (Two or more coats) |
| 25 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 26 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 27 | Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 28 | Precasting and placing in position 125 mm dia Bollards 600 mm high of required shape including providing M.S. Pipe Sleeve 50 mm dia 300mm long in the Bollard and M.S. Pipes 40 mm dia and 450mm long with 150x150x6mm M.S. plate welded at bottom and embedded 150mm in cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources), including necessary excavation of size 250x250x450mm deep for the same in bitumen/concrete pavement at specified spacing |
| 29 | Supply and fixing of Glass Fiber Reinforced Concrete ( GFRC ) Produced in accordance with PRE CAST INSTITUTE ( U.S.A) MANUAL 128 EDN 4 , conforming Jaali in approved size pattern , Design , thickness and colourMade by MRK GRC or Equivalent .The Jaali should be made from 53 grade white portland cement manufactured by J.K cement or equivalent having minimum compressive strength of 40 N / m Sqm , quartz, fine silica sand . \, Alkali resistant Glass Fiber manufactured by Nipon or Sant Gobin or owens corning or equivalent , super plasticizers and polymers manufactured by BASF , Sika MYK Schomburg or equivalent . The material casting should take place in Synthetic Rubber / FRP Mould manufactured by Reckli or equivalent . The Fixing of Jaali should be dry fixing i.e to be done with GI fastners , dash fastners , self - scerw and pins on MS frame or wall / RCC .Providing and Fixing Large Free standing GRC ColumnSize4500 mm * 450mm * 450 mm Including loading unloding cartage all complete as per approved by Consultant and Enginneer in Charge ( Aor) |
| 30 | Supplying and stacking of good Earth at site including royalty and carriage upto 5 Km complete ( earth measured in stacks will be reduced by 20 %for payment) The PhValue of Good earth Should be 5.50 to 8.50 only . |
| 31 | Prepration of beds for hedging and shrubbery byexcavating 60 cm deep and trenching the excavated base to a further depth of 30 cm , refilling theexcavating 60 cm deep and trenching the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 ( 8 parts of stacked volume of earth after reduction by 20 % : one partof stacked volume of slugde or manure after reduction by 8%) flooding with water, filling with earth if necessary ,watering and finally finedressing , leveling etc. including stacking and disposal of materialsdeclared ,unserviceable and surplus earth by spreading and leveling asdirected, with a lead of 50 m, lift up to 1.5 m complete ( cost of sludge , manure of extra earth to be paid for separately) |
| 32 | Digging of holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in ratio of 2: 1 by volume ( 2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8% ) flooding with water , dressing including removel of rubbish and surplus earth , if any withall leads and lifts ( cost of manure, sludge or extra good earth if needed to be paid for separately )*Holes 90 cm dia , and 90 cm deep |
| 33 | Supplying and stacking of well decomposed cow dung manure at site including royalty, carriageloading, unloading with all lead and lift.( manure measurment in stackes will be reduced by 8% for payment) |
| 34 | Providing & laying Selection no. 1 grass truf with earth 50 mm to60 mm thickness of existing ground prepared with proper level and ramming with required tooles wooden and than rolling the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly , as per direction of officer in charge |
| 35 | Supplying best quality Specimentrees ofspecies with their specification- mentioned bleow which are healthy and completly free from all diseses , ready for transplanting with approprate cuts and set in gunny begs / propylene begs as the case may be including labour , loading , unlodingby mechinical or manual means including cartage |
| 36 | Ornamental & Flowering Trees |
| 37 | Bauhinia blakeana- Specimen Ht 10\" Girth 4\" |
| 38 | Callistemon Citrinus - Bottle Brush - SpecimenHt 12\"Girth 6\" |
| 39 | Plumeria alba/ obtusa - Specimen Ht 10\" / Girth 10\" |
| 40 | Tabebuia argentea - Yellow- SpecimenHt 12\" /Girth 10\" |
| 41 | Tabebuia Palmeri - Specimen Ht 12\"/Girth 6\" |
| 42 | Terminalia Mantaly Green - Specimen Ht 12\"/Girth 8\" |
| 43 | Dombeya wallichii |
| 44 | Topiary &Balls & Conifers |
| 45 | Ficus Retusa Topairy well developed with fresh & healthy 5 to 6 big ball specific size and shape 180 to 210cm ht in 40 cm Cement Pot |
| 46 | Topairy plant of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht. plant, in 35 cm Cement Tray /Cement Pot |
| 47 | Syzygium Myrtifolium |
| 48 | Bougainvillea Single Stem - Ball Specimen Ht 3\"/Dia 3\" |
| 49 | Yucca Elephentipes -Multi Stems Ht 7\" - 8\" |
| 50 | leucophyllum -Ht 2\" |
| 51 | Radermachera Ht 7\" |
| 52 | Palms & Cycads And Bamboo |
| 53 | Ravenala MadagascariensisHt - 12\" |
| 54 | Supply of best quality Shrubs grown in pots / poly bags of Species with their specification - mentioned below, which are healthy and completely free from all disease, ready for Transplanting, inclusive of Labour, Loading, Unloading by Manual means and Cartage. All plants to be approved before planting by Officer -in Charge.The minimum Height of Plants to be 30 cms to 60 cms depending on the Species. |
| 55 | Ornamental Shrubs |
| 56 | Cestrum nocturnum (Raat ki Rani) of height 60-75 cm. with 4-5 branches in bag of size 25 cm |
| 57 | Gardenia jasminoides of height 45-60 cm. with 3-4 branches in earthen pot of size 20 cm |
| 58 | Providing and stacking of New VaritesHibiscus FiveColursHt 3\" |
| 59 | Ixora Singaporensis Mix |
| 60 | Lantana Camara Depressa |
| 61 | Supply of best quality House Plants, Hedges & Ground cover, Succulents Bulbs & Rizomes,Reeds & Grasses and Acquatic Plants - grown in pots / poly bags of Species with their specification - mentioned below, which are healthy and completely free from all disease,ready for Transplanting, inclusive of Labour, Loading, Unloading by Manual means and Cartage. All plants to be approved before planting by Officer -in Charge.The minimum Height of Plants to be 15 cms to 90 cms depending on the Species. |
| 62 | House Plants, Hegdes & Ground Cover |
| 63 | Providing and stacking of Asparagus marrie, well developed 15 to 20 leaves, full of branches and foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
| 64 | Cuphea chinensis of ht. 20-30 cm full of branches and healthy foliage in 15 cm size of Earthen Pot / Plastic Pot. |
| 65 | Dianella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot / Plastic Pot. |
| 66 | Wadelia trilobata,full of leaves in 15 cm size of Earthen Pot / Plastic Pot |
| 67 | Providing and stacking of Ficus long Island of height 15 cm to 20 cm, full of branches and foliage in 20 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge. |
| 68 | Providing and stacking of Clerodendrum inerme having ht. 25 cm to 30 cm multi branched in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
| 69 | Pandanaus Variegata( Golden New varites) |
| 70 | Rhoeo Spathacea Compacta |
| 71 | Lantana SellowianaPP |
| 72 | Succluents , Bulbs & Rizome |
| 73 | AgaveMix Varieties |
| 74 | Furcaria Variegated hybrid well developed with fresh & healthy foliage 20 and above attractive leaves in 35 cm Cement Pot. |
| 75 | Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in earthen pot of size 20 cm . |
| 76 | Reeds & Grasses and Aquatic Plants |
| 77 | Pennisetum Foxtrot - Fountain Grass |
| 78 | Pennisetum Setaceum - Red Switch Grass |
| 79 | Plantation of Trees, Shrubs , and Hedge at site i/c watering of un serveiceable materials as per direction if officer in charge ( excluding cost of plant & water) |
| 80 | Trees Plant |
| 81 | Shrubs Plant |
| 82 | Hedge Plant / Ground cover |
| 83 | Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department and other T & P material/articles shall be provided by the contractor) and as per direction of officer in charge. * Trees for 1200 no (beyond 8 year Slow & beyond 6 Fast growing group)*For 24 Months ( 1900 Tressx 24 Months ) |
| 84 | Complete maintenance of shrubs (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. * For 24 Months ( 6400Shrubs x 24 Months ) |
| 85 | Cutting of Hedge/Edge including removing of cut material, cleaning, hoeing of hedge/edge bed watering, manureing and applying insecticides and fungicides etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge.*For 24 Months ( 7724 Sqm Hedgex 24 Months ) |
| 86 | Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, edge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide, lawn mover and brush cutter with fuel & other T & P material/ articles shall be provided by the department. *Open spaces Per Sqm/ (1Mali for 3.00 Acre). |
| 87 | Providing and wartering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts asper direction of officer-in-charge. *For 24 Months (3 Tanker Per Day x 24 Months /730 Day) |
| 88 | Providing of Pvc pipes ( IS 4985- 88) and fiittings & Accessories like tees elbow bends junctions Reducer etc. as required / directed at site |
| 89 | PVC Pipe 63mm OD-6kg/cm2 |
| 90 | PVC Pipe 40mm OD-6kg/cm2 |
| 91 | Providingof pop up sprinkler 4\"\" with flow shut off device (4\"\" pop up height from bottom to centre of discharging nozzle) from (9 to 14 Mtr Radius) with in-stem pressure regulator (PRS),Flow shut off feature, Check Valve, Slip Clutch Mechenism complete with required nozzle. Make - Hunter USA |
| 92 | Providingof swing joint3/4\"\" with PP clamp saddle with chromed nut bolt & nitrile rubber gasket.Make - Hunter USA |
| 93 | Spray pop up sprinkler 4\"\"- bdoy with pressure-activated, co-moulded soft elastomer wiper seal, (5 to 7 Mtr Radius)with check valve, wiper seal, flow sheet complete with required nozzle.Make -Hunter USA |
| 94 | Providing of Various Valves with required Fittings &Tapping PP Clamp Saddles with Chromed Nut Bolt &Nitrile Rubber Ring . |
| 95 | PVC butter fly valve 140mm (4\"\") PN 10 Make - Harit / Netafim |
| 96 | PVC ball valve 63mmPN 16 Make - Harit / Netafim |
| 97 | 2\"\" double acting air cum vacum release valve heaving inbuilt surge protection with GM valve. Make - Harit / Netafim |
| 98 | Quick coupling hydrant valve 3/4\"\" with five sets of key & sweilve elbow. Make - Harit / Netafim |
| 99 | Round valve box 10\"\" Make - Harit |
| 100 | Non return valve 6\"\" Make - Harit |
| 101 | Header assembly 4\"\"/6\"\" for each filter & pump saction made of galvanized pipes or PVC Sch 80 pipe fittings. Make - Harit / Netafim |
| 102 | Glyserene fillrd pressure gauge 2\"\" dia Make / Netafim |
| 103 | Level Control Valve - Hydulic Diapham PE Valve with External Float 4\"Make - Harit / Netafim |
| 104 | SandSeparator - Vortex Technology -10 Bar Operating Pressure , Polymeride with Sand evacution Tank with Flish Valve - Hydrulic Type with ControllerMake - Harit / Netafim |
| 105 | TR Concrete bench Supply of concrete bench as per approved design casted in FRP mould for uniform surface straingthness and appropriate edge precasted with M-25 concrete mix appropriate reinforcement, the other surface to be coated with sealer. |
| 106 | Providing and fixing of Signage / logo UPSIDA of Size 5000x1300x230 mm height approx in Red sand Stonefinished as per attached drawing/image and placing on finished platform as attached drawing without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 107 | Providing and fixing of Sarswati Sclpture of Size 8000mm height approx in 4700x3600 mm Red sand stonefinished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 108 | Providing and fixing of Yoga sculptures of Size 3500 mm height approx in 4500 x300 mm Red sand stone finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 109 | Providing and fixing of Yoga sculptures of Size 1800 mm height approx in 1500 x300 mm Red sand stone finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 110 | Providing and fixing of BookSculptures of Size 6100 mm height approx in 4600 x115mm Red sand stone finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 111 | Providing and fixing of Decorative Column of Size 5000 mm height approx in 900 x 900 mm Red sand stone finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 112 | Providing and fixing of MeditationSculptures of Size 4800 mm height approx in 3100 x300 mm Red sand stone finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 113 | Providing and fixing of MeditationSculptures of Size 3100 mm height approx in 3000 x300 mm Red sand stone finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 114 | Providing and fixing of Decorative Poleof Size 4300 mm height approx in 800 x 800 mm Red sand stone finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 115 | Providing and fixing of Mandala Art Sculptures of Size 4000mm height approx in 4500 x300 mm Red sand stone finished as per attached drawing and placing in position without damaging the edges complete as per instruction from consultant and Engineer-in-charge. |
| 116 | Supply & Fixing of Locable DUO Dustbin . Outer cabinet of dustbin will be made 3 mm thick FRP material of overall size 406 X 813 X 813 mm with Top open able . The dustbin will be containing 2Nos inner bucket of 60 Lt . Capacity each thebucket will be LLDPE material . The iuter body will be customized with Noida logo ECO Vinyle material only in front side of dustbin . The dustbin will be grouted with H shape bracket and 150 mm long dash fastner at site . |
| 117 | MS Frame: Supply, fabrication of MS frame consisting of M.S. pipes, base plates & normal anchors. The frame shall be welded and grinded to smooth finish as per drawing. 1-Painting- The MS frame shall be cleaned of girt/grim andoil/grease deposit. The frame shall be sand papered to remove rust. The frame shall be painted with PU primer tofinish. After primer the frame, NC putty shall be applied over the frame and it will be wet sand papered to a smooth glossy finish. The ready surface will be painted 2 coats of PU paint 2 -Fabric: Providing & fixing of Fabric- Fabric Ferrari 902 over frame includingwire rope and plates. The fabric will be welded to shape and pattern. The joint shall have weld width of 40mm.The joint will have a homogeneous welded of 40 mm The fabric shall be installed, tensioned using atensioning device and shall not sag at any point. the fabricwill be fixed on the frame with fixing accessories like aluminium section with powder coated top covers, self drilling screws. |
| 118 | Electrical Works |
| 119 | Supply of10 watt Mino spike light for building facade. Fixture to be made of MS alloy in 10W LED engine with a beam of 36 degree togiveaspecifiedcoveragetolit.ThediffuseristoughenedClearglassof6mmthicknesswithopticalreflectortoreduceglare controlled, Silicone clear gasket, SS fasteners. This luminaire contains built-in LED modules. Lifespan of the luminaire > 60,000 hours at40°C.Driverefficiency>80%,powerfactor>0.90,Operatingtemp.-15°Cto+50°C.THD<15%,and complete in all respects as per directions of engineer I/C having make of Philips/Bajaj/Vak/Mayfair/havells/Twinkle/K-Lite/ VS Energy |
| 120 | Supply of9W uplight for building facade.Fixture to be made of Die-Cast aluminium alloy housing 316 grade stainless steel front ring. Fixture with a beam of 24 degree to give a specified area coverage to lit. The diffuser is toughened Clear glass lens to desired illumination, Silicone clear gasket, SSfasteners. Thisluminaire containsbuilt-in LED modules.with monkey protection Lifespan of the luminaire > 60,000 hours at 40°C. Driver efficiency >80%, power factor >0.90, Operating temp. -15°C to +50°C.THD <15%,and complete in all respects as per directions of engineer I/C having make of Philips/Bajaj/Vak/Mayfair/havells/Twinkle/K-Lite/ VS Energy |
| 121 | Supplyof linearflexiblestriplightforbuildingfacade whichiscomposed withLed inseriesjacketedby aninner plastic extrusion with IP 67 encapsulation in a tube. It is used to illuminate the overall boundary of the monuments with round or arc shape in 10W per mtr, color temperature 3000K, 12VDC driver. Led strip to be mounted with the help of clips and complete in all respects as per directions of engineer I/C having make of Philips/Bajaj/Vak/Mayfair/havells/Twinkle/K-Lite/ VS Energy |
| 122 | Supply of decorative Coloumn light in 4000mm height it is fabricated from aluminum extrusions or MS with precisely cut pattern for sophisticated illuminated presentation. Base is made of galvanized die cast aluminium .Diffuser is made of UV stabilized clear or opal PMMAISsuitablefor60WLED,IP65in3000k.and complete in all respects as per directions of engineer I/Chavingmakeof Philips/Bajaj/Vak/Mayfair/Havells/Twinkle/K-Lite/VS Energy/ VS Energy |
| 123 | Supply ofdecorative signage Coloumn light in 4000mm height it is fabricated from aluminum extrusions or MS with precisely cut pattern for sophisticated illuminated presentation. Base is made of galvanized die cast aluminium .Diffuser is made of UV stabilized clearoropalPMMAISsuitablefor40WLED,IP65in3000k.complete in all respects as per directions of engineer I/Chavingmakeof Philips/Bajaj/Vak/Mayfair/havells/Twinkle/K-Lite/ VS Energy |
| 124 | Supply and fixing following capacity of automaticstreet light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting ofTSO100serieswithcontactors,HRCfuses,isolatingswitchmetering instrument& instrument boxwithCTsetc. in caseofTPN, complete in all respect as per UPPWD Sch. No. 807(f) (ii) 40 A TPN |
| 125 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc ccomplete in all respects as per UPPWD Sch. No.501(J) 25 sq. mm 3-1/2 core . |
| 126 | Supply and laying and fixing of 50 mm dia GI pipe trench less through manual Boggi Method including trenchimg 90 cm deep and refilling etc as per jon no ED SHC (93) dated 10/05/2023 |
| 127 | Supply, installation, testing and commissioning of Cable termination with glands and lugs in the electrical panel with all necessary accessories as per Job No ED1(84) Dated 14.08.2024 |
| 128 | Supply, installation, testing and commissioning of Chemical Earthing for panels per Job No ED1(84) Dated 14.08.2024 |
| 129 | operation ,maintenace and cleaning and regular keep up for(1+2) years of the entire systems of gates |
