|
| 1 | Part A-Centrifugal Pump Set (Monoblock/ Coupled) |
| 2 | Rewinding of three phase squirrel cage induction motor ofMonoblock pump sets including all necessary material and of the same characteristics as original with required size of super enameled copper wire (including cost of copper wire),\"E\" class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including transportation of motor pump to and from Div/AEn/JEn store complete as per direction of engineer in charge. |
| 3 | 3 H.P. |
| 4 | 5 H.P. |
| 5 | 7.5 HP |
| 6 | 10.00 HP |
| 7 | 12.5 HP |
| 8 | 15.00 HP |
| 9 | 17.50 HP |
| 10 | 20.00 HP |
| 11 | SUPPLY & FIXING OF SPARE PARTS FOR MONOBLOCK PUMPSET (MOTOR + PUMP) |
| 12 | Connection Plates |
| 13 | up to 10 HP |
| 14 | 10 HP to 20 HP |
| 15 | Cooling Fan |
| 16 | up to 10 HP |
| 17 | 10 HP to 20 HP |
| 18 | GM/SS bush |
| 19 | Upto 10 HP |
| 20 | 10 HP to 20 HP |
| 21 | Mechanical reconditioning of Bearing sheet |
| 22 | Upto 10 HP |
| 23 | 10 HP to 20 HP |
| 24 | Mechanical reconditioning ofImpeller sheet and Key way slot |
| 25 | Upto 10 HP |
| 26 | 10 HP to 20 HP |
| 27 | Oil seal |
| 28 | Upto 10 HP |
| 29 | 10 HP to 20 HP |
| 30 | Labour charge for opening and fitting of pump sets |
| 31 | Upto 10 HP |
| 32 | 10 HP to 20 HP |
| 33 | Rewinding of three phase squirrel cage induction motor of HSC pump sets including all necessary material and of the same characteristics as original with required size of super enamelled copper wire (Including cost of copper wire) \"E\" class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including making electric connection at site of installation of motor with starter, alignment with pump setsand transportation to and fro from installation site complete as per direction of engineer in charge at site. |
| 34 | Above 15.00 HP but upto 17.50 HP |
| 35 | Above 17.50 HP but upto 20.00 HP |
| 36 | Above 20.00 HP but upto 25.00 HP |
| 37 | Above 25.00 HP but upto 30.00 HP |
| 38 | Above 30.00 HP but upto 35.00 HP |
| 39 | Above 35.00HP but upto 40.00 HP |
| 40 | Above 40.00 HP but upto 45.00 HP |
| 41 | Above 45.00 HP but upto 50.00 HP |
| 42 | Above 50.00 HP but upto 60.00 HP |
| 43 | Above 60.00 HP but upto 75.00 HP |
| 44 | Above 75.00 HP but upto 100.00 HP |
| 45 | SUPPLY & FIXING OF SPARE PARTS HSC PUMP SETS (MOTOR + PUMP) |
| 46 | Connection Plates |
| 47 | 5 HP to 20 HP |
| 48 | 20 HP to 30 HP |
| 49 | 30 HP to 50 HP |
| 50 | Above 50 HP to 100 HP |
| 51 | Cooling Fan |
| 52 | 5 HP to 20 HP |
| 53 | 20 HP to 30 HP |
| 54 | 30 HP to 50 HP |
| 55 | Above 50 HP to 100 HP |
| 56 | Fan Cover |
| 57 | 5 HP to 20 HP |
| 58 | 20 HP to 30 HP |
| 59 | 30 HP to 50 HP |
| 60 | Above 50 HP to 100 HP |
| 61 | G.M./SS Gland Guide Bush |
| 62 | 5 HP to 20 HP |
| 63 | 20 HP to 30 HP |
| 64 | 30 HP to 50 HP |
| 65 | Above 50 HP to 100 HP |
| 66 | Shaft with Sleeve Chuck Nut |
| 67 | 5 HP to 20 HP |
| 68 | 20 HP to 30 HP |
| 69 | 30 HP to 50 HP |
| 70 | Above 50 HP to 100 HP |
| 71 | Shaft Chuck Nut |
| 72 | 5 HP to 20 HP |
| 73 | 20 HP to 30 HP |
| 74 | 30 HP to 50 HP |
| 75 | Above 50 HP to 100 HP |
| 76 | G.M. Neck Ring |
| 77 | 5 HP to 20 HP |
| 78 | 20 HP to 30 HP |
| 79 | 30 HP to 50 HP |
| 80 | Above 50 HP to 100 HP |
| 81 | Bush Shaft Sleeve of G.M. |
| 82 | 5 HP to 20 HP |
| 83 | 20 HP to 30 HP |
| 84 | 30 HP to 50 HP |
| 85 | Above 50 HP to 100 HP |
| 86 | G.M. Gland Cover |
| 87 | 5 HP to 20 HP |
| 88 | 20 HP to 30 HP |
| 89 | 30 HP to 50 HP |
| 90 | Above 50 HP to 100 HP |
| 91 | S.S. Shaft (Non Magnetic) |
| 92 | 5 HP to 20 HP |
| 93 | 20 HP to 30 HP |
| 94 | 30 HP to 50 HP |
| 95 | Above 50 HP to 100 HP |
| 96 | G.M. Shaft Sleeve Check Nut |
| 97 | 5 HP to 20 HP |
| 98 | 20 HP to 30 HP |
| 99 | 30 HP to 50 HP |
| 100 | Above 50 HP to 100 HP |
| 101 | M.S. Shaft Check Nut |
| 102 | 5 HP to 20 HP |
| 103 | 20 HP to 30 HP |
| 104 | 30 HP to 50 HP |
| 105 | Above 50 HP to 100 HP |
| 106 | Cooling pipe set with nozzle & Nut |
| 107 | 5 HP to 20 HP |
| 108 | 20 HP to 30 HP |
| 109 | 30 HP to 50 HP |
| 110 | Above 50 HP to 100 HP |
| 111 | AIR Cock |
| 112 | 5 HP to 20 HP |
| 113 | 20 HP to 30 HP |
| 114 | 30 HP to 50 HP |
| 115 | Above 50 HP to 100 HP |
| 116 | JOB WORK FOR REPAIR OF PUMP MOTOR |
| 117 | Bearing Housing (rebuilding, turning & finishing) |
| 118 | 5 HP to 20 HP |
| 119 | 20 HP to 30 HP |
| 120 | 30 HP to 50 HP |
| 121 | Above 50 HP to 100 HP |
| 122 | Bearing Cap (rebuilding, turning & finishing) |
| 123 | 5 HP to 20 HP |
| 124 | 20 HP to 30 HP |
| 125 | 30 HP to 50 HP |
| 126 | Above 50 HP to 100 HP |
| 127 | Impeller Reconditioning for all type of Pump |
| 128 | 5 HP to 20 HP |
| 129 | 20 HP to 30 HP |
| 130 | 30 HP to 50 HP |
| 131 | Above 50 HP to 100 HP |
| 132 | Labour Charges for Dismantling & Assembling of Pump |
| 133 | 5 HP to 20 HP |
| 134 | 20 HP to 30 HP |
| 135 | 30 HP to 50 HP |
| 136 | Above 50 HP to 100 HP |
| 137 | Coupling with stud and rubber bush |
| 138 | 5 HP to 20 HP |
| 139 | 20 HP to 30 HP |
| 140 | 30 HP to 50 HP |
| 141 | Above 50 HP to 100 HP |
| 142 | Supply & Fixing of tyre coupling sets according torelevant IS code in Centrifugal couple pump sets of approved make Unit. This job also included re-alignment of centrifugal couple pump set after fixing of tyre coupling set as per directed by Engineer-in charge. |
| 143 | Type 14 Nos. set |
| 144 | Type 15 Nos. set |
| 145 | Type 16 Nos. set |
| 146 | Type 17 Nos. set |
| 147 | Supply and fixing Ball bearing of Various size for centrifugal/monoblock pump set of ISI Mark as per specification and approved make by EIC. |
| 148 | 6304 or equivalent size |
| 149 | 6305 or equivalent size |
| 150 | 6306 or equivalent size |
| 151 | 6307 or equivalent size |
| 152 | 6308 or equivalent size |
| 153 | 6309 or equivalent size |
| 154 | 6310 or equivalent size |
| 155 | 6311 or equivalent size |
| 156 | 6312 or equivalent size |
| 157 | 6316 or equivalent size |
| 158 | 6317 or equivalent size |
| 159 | 6318 or equivalent size |
| 160 | 6319 or equivalent size |
| 161 | NU319C or equivalent size |
| 162 | Routine maintenance of centrifugal coupled pump and motorincluding opening, cleaning, greasing and refitting / changing of ball bearing if required, gland refilling and replacing all rusted studs, replacing rubber bushes & coupling nut & bolts for coupling pulley, tightening all nut & bolts of foundation, baseplate, pump & motor etc. Checking & correcting alignment of pump & motor including necessary materials i.e. grease, nut & bolts, studs, washers, gland packing and rubber bushes etc. work done at site complete job |
| 163 | 5 HPto 20 HP |
| 164 | 20 HPto 30 HP |
| 165 | Above 30 HP and up to 50 HP |
| 166 | Above 50 HP and up to 100 HP |
| 167 | Cleaning of pump house by air blower/ vacuum cleaner or other means including removing of JALA from ceiling and walls etc. complete Job. |
| 168 | Cleaning of Electric PanelPMCC by air blower/vacuum cleaner or other means including tightening of loose connections etc. complete job. |
| 169 | Replacing of damaged/broken gland packing plate with new gland packing plate suitable for centrifugal pump shafts and nut & bolts etc. complete job. |
| 170 | 5 HP to 20 HP |
| 171 | Above 20 HP and up to 30 HP |
| 172 | Above 30 HP and up to 50 HP |
| 173 | Above 50 HP and up to 100 HP |
| 174 | Part B-Submersible Pump Set |
| 175 | Repair Rewinding of Submersible motor includes full servicing and rewinding (wherever required) as per manufacturer\"s specification and to the satisfaction of Engineer Incharge. It includes the replacement of minor parts such as bushes (oil seal bush) Nut Bolts, washers, cable seal, gland ring, vent plug, water drain plug, etc. complete job |
| 176 | Up to 3 HP V-6 |
| 177 | Above 3HP to 5 HP V-6 |
| 178 | Above 5HP to 7.5 HP V-6 |
| 179 | Above 7-5 HP to 10 HP V-6 |
| 180 | Above 10 HP to 12.5 HP |
| 181 | V-6 |
| 182 | V-8 |
| 183 | Above 12.5 HP to 15 HP |
| 184 | V-6 |
| 185 | V-8 |
| 186 | Above 15 HP to 17.5 HP |
| 187 | V-6 |
| 188 | V-8 |
| 189 | Above 17.5 HP to 20 HP |
| 190 | V-6 |
| 191 | V-8 |
| 192 | Motor opening cable jointing & refitting charges when rewinding is not required. |
| 193 | V-6 |
| 194 | V-8 |
| 195 | Providing & Replacement of G.M./S.S. Bushes for all types of motors (per set of 4Nos.) including cost of sleeves |
| 196 | V-6 |
| 197 | V-8 |
| 198 | Providing & Replacement of thrust bearing for all types of motor. It includes cost of all components connected with thrust bearing. |
| 199 | V-6 |
| 200 | V-8 |
| 201 | Replacement of thrust plate for all types of motors |
| 202 | V-6 |
| 203 | V-8 |
| 204 | Supply and fixing spare parts for repair of pump set including cost of opening refitting, servicing, and machining, if required. It also includes the cost of nut bolt, studs, washer packing, keys etc. complete. |
| 205 | Providing & fixing of GM neck rings parts on impeller. |
| 206 | Plain Type V-6 |
| 207 | Bowel typeV-6 |
| 208 | Plain Type V-8 |
| 209 | Bowel typeV-8 |
| 210 | Providing & Fixing of GM/SS bush per piece |
| 211 | Plain Type V-6 |
| 212 | Bowel typeV-6 |
| 213 | Plain Type V-8 |
| 214 | Bowel typeV-8 |
| 215 | Providing & replacement of G.M. Impeller |
| 216 | Plain Type V-6 |
| 217 | Bowel typeV-6 |
| 218 | Plain Type V-8 |
| 219 | Bowel typeV-8 |
| 220 | Providing & replacement of Nylon Impeller |
| 221 | Plain Type V-6 |
| 222 | Bowel typeV-6 |
| 223 | Plain Type V-8 |
| 224 | Bowel typeV-8 |
| 225 | Providing & fixing CI Diffuser/ guide vans per piece |
| 226 | V-6 |
| 227 | V-8 |
| 228 | Providing & fixing Gun metal Diffuser/ guide vans per piece |
| 229 | V-6 |
| 230 | V-8 |
| 231 | Providing & fixing Nylon Diffuser/ guide vans per piece |
| 232 | V-6 |
| 233 | V-8 |
| 234 | Providing & fixing Microlone Guide per piece |
| 235 | V-6 |
| 236 | V-8 |
| 237 | Providing & fixing of CI body per piece |
| 238 | Plain Type V-6 |
| 239 | Bowel typeV-6 |
| 240 | Plain Type V-8 |
| 241 | Bowel typeV-8 |
| 242 | Pump opening & fixing including machining & all finishing work for desired performance |
| 243 | Plain Type V-6 |
| 244 | Bowel typeV-6 |
| 245 | Plain Type V-8 |
| 246 | Bowel typeV-8 |
| 247 | Impeller welding & turning (if not replaced) |
| 248 | Plain Type V-6 |
| 249 | Bowel typeV-6 |
| 250 | Plain Type V-8 |
| 251 | Bowel typeV-8 |
