Tender For Special Repair And Maintenance Of Marine Work Shop And Office At Kadmat
Tender Value
Ref. Documents
Estimated cost
Bid Submission
17 Feb 2025
0 days left
EMD
16580
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kadmat → Lakshadweep
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Special Repair And Maintenance Of Marine Work Shop And Office At Kadmat
BOQ
| Sl. No. | Item Description |
| 1 | Surface dressing of the ground including removing vegitation and in equalities not exceeding 15cm deep and disposal of rubbish lead up to 50 metres and lift up to 1.5 metres |
| 2 | Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan)ncluding dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m All kinds of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc layers not exceeding 20cm plinth, sides of foundations etc layers not exceeding 20cm and watering lead up to 50 mtr and lift up to 1.5 metres |
| 4 | Providing and laying cement concrete 1: 4:8 ( 1 cement: 4 M.Sand: 8 granite chips ) foundation and plinth.Stone aggregate 40mm nomonal size including cost of cement,Labour Rate( Granite chipes &M.sand issued by the department) |
| 5 | Reinforced cement concrete work in well-steining, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stoneggregate 20 mm nominal size) |
| 6 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All kind of work upto plinth level :1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 7 | Centring and shuttering including strutting, propping etc. And removal of form for :Suspended floors, roofs, landings, balconies and access platform |
| 8 | Centring and shuttering including strutting, propping etc. and removal of form for :Well steining |
| 9 | 12mm cement plaster 1:3 (1cement :3 metal sand) finished with floating coat of neat cement |
| 10 | 6mm cement plaster to ceiling 1:3(1cement :3 metal sand) |
| 11 | P/F 2HP Pumbset with all accessariysanddirection of engineer(Labour) |
| 12 | Providing and fixing nominal guage PVC Pipe of approved quality compleate with special flang compression type fittings including trenching and re filling etc. External work32mm dia |
| 13 | Providing and fixing 30 mm thick panelled, glazed or panelled and glazed shutters for doors windows and clerestory windows including anodised aluminium butt hinges with necessarycrews. First class Karimaruthu or equivalent |
| 14 | Providing and fixing karimaruthu wood or equivalent 25 mm squre wooden bars at required spacing in wooden frames of windows and clerestory windows |
| 15 | Providing and fixing anodised Aluminium tower bolt (barral type) anodised transparent or dyed to required color and shade with bolts , nuts and screws etc complete |
| 16 | Providing and fixing anodised Aluminium handle anodised transparent or dyed to required color and shade with bolts ,nuts and screws etc complete. |
| 17 | Providing and fixing anodised Aluminium hooks and eyes anodised transparent or dyed to required color and shade with bolts , nuts and screws etc complete. |
| 18 | Supplying and fixing rolling shutters of approved make, made of required size M.S.laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters .2 80x1.20 mm M.S. laths with 1.20 mm thick top cover |
| 19 | Providing and fixing ball bearing for rolling shutters |
| 20 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: |
| 21 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m² |
| 22 | Providing ridgesin C.G.S. sheet roofing for making opening of area exceeding 40 sq. decimeter for chimney stacks, sky light etc.:1.00 mm thick |
| 23 | Painting Wood work with Deluxe Multi surface paintto give an even shade.Two or more coats applied on @0.90ltr/10 sqm) over under coat of primer applied @ 0.75 ltr/10 sqm of approvednd manufacture (Berger/Birla or equivalent) |
| 24 | Painting Steel work with Deluxe Multi surface paintto give an even shade.Two or more coats applied on @0.90ltr/10 sqm) over under coat of primer applied @ 0.80 ltr/10 sqm of approved and manufacture |
| 25 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. Complete |
| 26 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade One or more coats on old work |
| 27 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade One or more coats on old work |
| 28 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 29 | Renewing glass panes and refixing existing wooden fillets:Float glass panes of thickness 4 mm |
AI Tender Summary
Tender Timeline
Feb 11, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 17, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 17, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender