|
| 1 | Removing/taking out carefully old unserviceable worn out/components parts of the following wooden furniture and M&L for the same as listed below with new materials/components, made to finishing to receive polish all as specified, directed and shown on drawing:- |
| 2 | CHAIR EASY WOODEN (Drg No FD-229) |
| 3 | Front leg made out of 1st class hardwood all as specified. |
| 4 | Front Rail of seat frame with necessary holes for canning made out of 1st class hardwood all as specified. |
| 5 | Side Rail of seat frame with necessary holes for canning made out of 1st class hardwood all as specified. |
| 6 | Taking old worn out/damaged existing cane from chair easy wooden cleaning of caning holes without damaging the furniture & recanning of the same with white coloured new cane of 2mm width plastic half oval shape cane best qualitybeading with 4mm width plastic half oval shape cane (Godrej pattern) as shown in drawing. |
| 7 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 8 | CHAIR WRITTING (Drg No FD-280) |
| 9 | Front leg made out of 1st class hardwood all as specified. |
| 10 | Rear leg made out of 1st class hardwood all as specified. |
| 11 | Front Rail of seat frame with necessary holes for canning made out of 1st class hardwood all as specified. |
| 12 | Side Rail with necessary holes for canning made out of 1st class hardwood all as specified. |
| 13 | Back rest batten made out of 1st class hardwood all as specified. |
| 14 | Taking old worn out/damaged existing cane from chair writing cleaning of caning holes without damaging the furniture & recanning of the same with white coloured new cane of 2mm width plastic half oval shape cane best qualitybeading with 4mm width plastic half oval shape cane (Godrej pattern) as shown in drawing. |
| 15 | TABLE DINING FOR 4 PERSON OF SIZE 1200 mm x 900 mm x 760 mm (Drg No FD- 291) |
| 16 | Removing the old u/s top and S&F for new one made out of 18 mm thick particle board one side laminated exterior grade with 4mm teak wood beading all around and fixing the same on table in its original position as per drawing and providing new hard rubber shoes to the legs. |
| 17 | Removing worn out u/s leg and S&F for new legs of existing size and shape made out of 1st class well seasoned teakwood and fixing the same in its original position as per drg. |
| 18 | Removing the worn out u/s long rail of seat frame and S&F for new long rail of seat frame of existing size and shape made out of 1st class teakwood well seasoned and fixing the same in its original position as per drg. |
| 19 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 20 | PEG TABLE (Drg No FD-227) |
| 21 | Removing the existing unservicable leg from peg table andS&F for new leg made out of 1st class well seasoned teak wood of existing sizeand shape all as shown on drawing. |
| 22 | Removing the existing unserviceable broken long rail and S&F for 1st hard wood long rail 50 X 25mm all as specified & shown on drg. |
| 23 | Removing the existing unserviceable broken top of tableand S & F for new table top 18mm thick particle board commercial type (exterior grade) phynoil bonded with 1mm thick plastic laminated sheet ontop including providing 4mm thick second class hard wood beading all round table all as specified and shown on drg. |
| 24 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 25 | TABLE CENTRE (Drg No FD-274) |
| 26 | Removing the u/s broken leg and S&F for 1st class hard wood leg 45mm X 25mm all as specified & shown on drg. |
| 27 | Removing the existing unserviceable broken top and S&F for new table top 18mm thick particle board commercial type (exterior grade) phynoil bonded with 1mm thick plastic laminated sheet at the top, size of top 900mm X 450mm including providing 4mm thick second class hard wood beading all round including French polishing all as specified and shown on drg. |
| 28 | Removing the existing u/s broken top rail (shorter) and S&F for 1st class hard wood top rail (shorter) of size 50 X 25mm all as specified & shown on drg. |
| 29 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 30 | TABLE DINNING 08 PERSONS (Drg No. FD-273, 239) |
| 31 | Removing the existing unserviceable broken top and S&F for new table top 18mm thick particle board commercial type (exterior grade) phynoil bonded with 1mm thick plastic laminated sheet at the top, size as per existing including providing 4mm thick second class hard wood beading all round including French polishing all as specified and shown on drg. |
| 32 | Removing the existing unsv/broken legs of Table dining 8 persons and S&F for new legs made of 1st class hardwoodduly fixing PVC rubber shoe at the bottom of legs with mild steel screws complete all as specified and shown on drg. |
| 33 | Removing the existing unsv/broken top long rails of Table dining 8 persons and S&F for new long rails made of 1st class hardwood all as specified and shown on drg. |
| 34 | Removing the existing unsv/broken MS Right angle iron from corner of Table dining 8 persons and S&F for new mild steel angle iron with mild steel screws complete all as specified and shown on drg. |
| 35 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 36 | TABLE DINNING 06 PERSONS (Drg No. FD-273, 239) |
| 37 | Removing the existing unserviceable broken top and S&F for new table top 18mm thick particle board commercial type (exterior grade) phynoil bonded with 1mm thick plastic laminated sheet at the top, size as per existing including providing 4mm thick second class hard wood beading all round including French polishing all as specified and shown on drg. |
| 38 | Removing the existing unsv/broken legs of Table dining 06 persons and S&F for new legs made of 1st class hardwoodduly fixing PVC rubber shoe at the bottom of legs with mild steel screws complete all as specified and shown on drg. |
| 39 | Removing the existing unsv/broken top long rails of Table dining 06 persons and S&F for new long rails made of 1st class hardwood all as specified and shown on drg. |
| 40 | Removing the existing unsv/broken MS Right angle iron from corner of Table dining 06 persons and S&F for new mild steel angle iron with mild steel screws complete all as specified and shown on drg. |
| 41 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 42 | SOFA SET 05 SEATER WITH CUSHIONS (Drg No. FD-373) |
| 43 | Removing of wornout legs of 05 seater sofa and S&F for the new legs of size 35 x 70mm of 1st class hardwood . |
| 44 | Removing of wornout U/S front railslong sofa of size 35mm x 100mmin section of 1st class and S&F for new front rail of same site of 1st class hardwood. |
| 45 | Removing the old u/s wornout cushion of 100 mm thick of 40 density for single seater with cover and S&F for new cushion of 100 mm thick of 40 density for single seater cover with new tapestry cloth duly stritch with zip of best quality as approved GE. |
| 46 | Removing the old u/s wornout cushion of 100 mm thick of 40 density for three seater with cover and S&F for new cushion of 100 mm thick of 40 density for three seater cover with new tapestry cloth duly stritch with zip of best quality as approved GE. |
| 47 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 48 | TABLE DRESSING GENTS WITH MIRROR (Drg No. FD-230) |
| 49 | Taking out of existing unsv/broken top of Table dressing gents and S&F for new top of prelaminated particle board of 18mm thick one side Teak face and one side balancing white all as specified and shown on drg. |
| 50 | Removing the existing unsv/broken back of Table dressing gents and S&F for new back made of 6mm thick BWR grade plywood (05 Nos ply) duly fixed with 02 Nos of key hole all as specified and shown on drg. |
| 51 | Removing the existing unsv/broken mirror with frame incl 4mm thick back ply of Table dressing gents and S&F for new mirror frame made of second class hard wood duly fitted with 5.5mm thick new mirror alongwith 4mm thick BWR grade back plywood (03 Nos ply) all as specified and shown on drg. |
| 52 | CHARPOY IP PLY TOP (Drg No. FD/MAP-II/01) |
| 53 | Removing the existing u/s ply wood from Charpoy IP ply top and making the frame to its original position by tightening etcand S&F for new plywood (07 Nos of ply) of 12 mm thick BWR grade complete as directed by Engr. |
| 54 | Removing the u/s rubber shoes and S&F for hard rubber shoe of best quality as approved by GE all as per specified and shown on drg. |
| 55 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr |
| 56 | BED HARD PLY TOP (Drg No. FD/E6/MAP/08R) |
| 57 | Removing the existing u/s ply wood from hard bed ply top and making the frame to its original position by tightening etcand S&F for new plywood (07 Nos of ply) of 12 mm thick BWR grade complete as directed by Engineer-in-Charge. |
| 58 | Removing the u/s rubber shoes and S&F for hard rubber shoe of best quality as approved by GE all as per specified and shown on drg |
| 59 | Removing the existing u/s pre-laminated particle board of head board from bed and S&F for 18mm new pre-laminated particle board of head board as per existingas per drawing. |
| 60 | Removing the existing u/s pre-laminated particle board of foot board from bed and S&F for 18mm new pre-laminated particle board of foot board as per existing as per drawing. |
| 61 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 62 | TABLE DRESSING LADIES (Drg No. FD-252, 378) |
| 63 | Removing the existing unsv/broken drawers of Table dressing ladiesand S&F for new drawers made of 18mm thick prelaminated particle board and bottom of drawer with 6mm thick BWR grade plywood (05 Nos ply) duly fixed with Aluminium anodisedknobs 50mm all as specified and shown on drg. |
| 64 | Removing the existing unsv/broken back of Table dressing ladies and and S&F for new back of 18mm thick pre-laminated particle board one side teak face and one side balancing white including 4mm thick 2nd class hard wood beading all round complete all as specified and shown on drg. |
| 65 | Removing the existing unsv/broken top of Table dressing ladies and S&F for new top of prelaminated particle board of 18mm thick one side Teak face and one side balancing white all as specified and shown on drg. |
| 66 | Removing the existing unsv/broken side of Table dressing ladies and S&F for new side of prelaminated particle board of 18mm thick one side Teak face and one side balancing white all as specified and shown on drg. |
| 67 | Removing the existing unsv/broken mirror with 4mm thick back ply of Table dressing ladies and S&F for new mirror of 5.5mm thick suitable to the existing frame alongwith 4mm thick BWR grade back plywood (03 Nos ply) all as specified and shown on drg. |
| 68 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 69 | TABLE BED SIDE (Drg No. FD-276) |
| 70 | Removing the existing unsv/broken legs of table bed side and S&F for new legs of existing size and shape made out of 1st class well seasoned teak wook and finish the same in its original position complete all as specified and shown drg. |
| 71 | Removing the existing unsv/broken sides of Table bed side without drawer and S&F for new sides of prelaminated particle board of 18mm thick one side Teak face and one side balancing white all as specified and shown on drg. |
| 72 | Removing the existing unsv/broken top of Table bed side without drawer and S&F for new top of prelaminated particle board of 18mm thick one side Teak face and one side balancing white including 4mm thick 2nd class hard wood beading all round all as specified and shown on drg. |
| 73 | SOFA SET 04 SEATER (Drg No. FD-281, 373) |
| 74 | Removing of wornout front legs of 04 seater sofa and S&F for the new legs of size 35x70mm of 1st class hardwood complete as specified and directed. |
| 75 | Removing of wornout rear legs of 04 seater sofa and S&F for the new legs of size 35 x 70mm of 1st class hardwood complete as specified and directed. |
| 76 | Removing the old u/s wornout cushion of 100 mm thick of 40 density for 04 seater with cover and S&F for new cushion of 100 mm thick of 40 density for 04 seater cover with new tapestry cloth duly stritch with zip of best quality as approved GE. |
| 77 | CHAIR VERANDAH (Drg No FD-256) |
| 78 | Taking old worn out/damaged existing cane from chair verandah and making the frame by means of welding wherever required to bring its in original shape, cleaning of caning holes without damaging the furniture & recanning of the same with white coloured new cane of 2mm width plastic half oval shape cane best qualitybeading with 4mm width plastic half oval shape cane (Godrej pattern) as shown in drawing. |
| 79 | Removing the unservicable broken rubber shoes of chair verandah and S&F for rubber shoe of best quality as approved by GE and as specified and shown in drawing. |
| 80 | CHIAR DINNING (Drg No FD-279) |
| 81 | Front leg made out of 1st class harwood all as specified. |
| 82 | Rear leg made out of 1st class harwood all as specified. |
| 83 | Front Rail of seat frame with necessary holes for canning made out of 1st class harwood all as specified. |
| 84 | Side Rail of seat frame with necessary holes for canning made out of 1st class harwood all as specified. |
| 85 | Back Rail of seat frame with necessary holes for canning made out of 1st class harwood all as specified. |
| 86 | Short stiffener made out of 1st class harwood all as specified. |
| 87 | Back rest batten made out of 1st class harwood all as specified. |
| 88 | Taking old worn out/damaged existing cane from chair dinning cleaning of caning holes without damaging the furniture & recanning of the same with white coloured new cane of 2mm width plastic half oval shape cane best qualitybeading with 4mm width plastic half oval shape cane (Godrej pattern) as shown in drawing. |
| 89 | Removing of old u/s rubber shoes from chair dinning and S&F for new rubber shoes of best quality as approved by GE at the bottom of legs of chair dinning as specified and directed. |
| 90 | HAT STAND WITH MIRROR (Drg No FD-23(M), 233) |
| 91 | Removing of u/s or broken looking mirror from hat stand and S&F for 5.5mm thick new looking mirror of similar to the existing fixed in frame alongwith 4mmthick BWR grade back plywood (03 Nos ply) complete all as shown in drawing. |
| 92 | Removing the existing unsv prelaminated particle board of hat stand and S&F for new of prelaminated particle board of 18mm thick one side Teak face and one side balancing white of existing size duly supported with 4mm thick teak wood beading all round complete all as specified and shown on drg. |
| 93 | Removing of existing u/s peg hook and S&F for new brass peg hooks of existing size and shape with brass screws complete all as per drg. |
| 94 | SHOE RACK STEEL (Drg No. FD/E6/MAP/02R) |
| 95 | S&F for 300mm long, 3mm dia cold rolled pipes after replacement of old u/s or broken pipes complete all as per drawing. |
| 96 | S&F for 25mm dia cold rolled pipes of existing size and length including necessary welding with new parts after replacement of old u/s pipes complete all as per drawing. |
| 97 | S&F for 700mm long, 3mm dia cold rolled pipes after replacement of old u/s or broken pipes complete all as per drawing. |
| 98 | SIDE BOARD (Drg No FD-241) |
| 99 | Removing the existing unservicable leg of side board andS&F for new leg made out of 1st class well seasoned teak wood of existing sizeand shape all as shown on drawing. |
| 100 | Removing the existing knob of side board drawer and S&F for newstainless steel handle of 50mm long fixed with brass screws complete all as shown on drg. |
| 101 | Removing of existing unsv back plywood from side board and S&F for 6mm thick plywood (05 Nos ply), BWR grade as per existing size complete all as shown on drg. |
| 102 | Removing the existing unsv/broken side board shutterand S&F for new shutter made of 18mm thick prelaminated particle board (exterior grade) one side teak face and other commercial white all as shown on drg. |
| 103 | Removing the existing unservicable drawers andS&F for new drawers made out of 1st class well seasoned teak wood from knots duly french polished all as shown on drawing. |
| 104 | TABLE COMPUTER (Trade Pattern) |
| 105 | Removing of existing u/s top of table computer and S&F for new top made out of 18mm thickpre-laminated particle board (exterior grade) with beading all round all as shown in drg. |
| 106 | Removing of existing u/s pull out tray from table computer and S&F for new pull out tray made out of 18mm thickpre-laminated particle board (exterior grade) of existing shape & size and tray shall be fixed on telescopic channel. |
| 107 | Removing of existing u/s drawer of table computer and S&F for new drawer made out of 18mm thickprelam particle board exteriod grade of existing shape & size and drawer shall be fixed on telescopic channel. |
| 108 | Removing of existing u/s key board tray of table computer and S&F for new key board tray made out of 18mm thickprelam particle board exteriod grade of existing shape & size and tray shall be fixed on telescopic channel. |
| 109 | TABLE BED SIDE MAP (Drg No FD/E6/MAP/15R) |
| 110 | Removing the unservicable/broken/damaged top of table bed side and S&F for new top made out of prelaminated particle board of 18mm thick duly french polished as specified and shown in drawing. |
| 111 | Removing the unservicable handle of table bed side and S&F for new handle chromium plated made out of 75mm long, \"D\" type as approved by GE as specified and shown in drawing. |
| 112 | Removing the unservicable hard rubber from table bed side and S&F for new hard rubber to table bed side at the bottom of legs complete as specified and shown in drawing. |
| 113 | Removing the unserviceable/broken/damaged plywood from table bed side and S&F for new 6mm thick plywood (05 Nos ply), BWR grade all as specified and shown in drawing. |
| 114 | TEA POY (Drg No FD-278) |
| 115 | Removing existing u/s top of Tea poy and S&F for new top made of 18mm thick pre-laminated particle board fixed to mild steel frame with screw as specified and directed. |
| 116 | Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with high class french polish till the surface to require glossy shine finish obtain and as directed by Engr in charge. |
| 117 | ALMIRAH SMALL STEEL (Drg No FD-1032) |
| 118 | Taking out of broken door shutter and re-fixing the same existing door shutters in original position with pin type new steel hinges(02 Nos) of existing size duly welded as required including denting and painting the shutter matching the existing paint as shown in drawing as directed by the Engineer-in-Charge. |
| 119 | Removing the worn out u/s handle from the almirah and S&F for the new handle chromium plated (heavy duty) of best quality as approved by GE. |
| 120 | Removing the worn out u/s lock from almirah and S&F forwith new lock 6 lever with duplicate key ISI marked (Make:Godrej) of round shape and MS key plate as approved by GE duly fixed as shown in drawing. |
| 121 | Removing the worn out u/s leg and S&F for the new leg made out of MS sheet 1.00mm thickin its original position duly welded as required including painting the legs matching the existing paint as shown in drg. |
| 122 | M&L for preparation of external and internal surface of almirah small steel including derusting,grindingpaste putty ,sanding etc and applying two coats ofsynthentic enamal paint,with spray paint by compressor of Ist quality (Asian paints)duly colour approved by GE complete all as specified and directed by Engr in charge and shown on drawing. (Note: (i)Rusted poration shall be de-rusted and treated with one coat of red oxide primer before applying paint.(ii) Re-jointing by welding not exc.100mm in lenghth /Girth (Thickness of metal to be weld not Exc. 6mm) including one coat of synthetic enamal paint over a coat of red oxide primeron effected repaired/welded portion to match with existing) |
| 123 | ALMIRAH STEEL MEDIUM (Drg No FD- 1032) |
| 124 | All as per Srl No 24.01 but for almirah steel medium. |
| 125 | All as per Srl No 24.02 but for almirah steel medium. |
| 126 | All as per Srl No 24.03 but for almirah steel medium. |
| 127 | All as per Srl No 24.04 but for almirah steel medium. |
| 128 | All as per Srl No 24.05 but for almirah steel medium. |
| 129 | ALMIRAH STEEL LARGE (Drg No FD-1031) |
| 130 | Taking out of broken door shutter and re-fixing the same existing door shutters in original position with pin type new steel hinges(02 Nos) of existing size duly welded as required including denting and painting the shutter matching the existing paint as shown in drawing as directed by the Engineer-in-Charge. |
| 131 | Removing the worn out u/s handle from the almirah and S&F for the new handle chromium plated (heavy duty) of best quality as approved by GE. |
| 132 | Removing the worn out u/s lock from almirah and S&F forwith new lock 6 lever with duplicate key ISI marked (Make:Godrej) of round shape and MS key plate as approved by GE duly fixed as shown in drawing. |
| 133 | Removing the worn out u/s leg and S&F for the new leg made out of MS sheet 1.00mm thickin its original position duly welded as required including painting the legs matching the existing paint as shown in drg. |
| 134 | M&L for preparation of external and internal surface of almirah large steel including derusting,grindingpaste putty ,sanding etc and applying two coats ofsynthentic enamal paint,with spray paint by compressor of Ist quality (Asian paints)duly colour approved by GE complete all as specified and directed by Engr in charge and shown on drawing. (Note: (i)Rusted poration shall be de-rusted and treated with one coat of red oxide primer before applying paint.(ii) Re-jointing by welding not exc.100mm in lenghth /Girth (Thickness of metal to be weld not Exc. 6mm) including one coat of synthetic enamal paint over a coat of red oxide primeron effected repaired/welded portion to match with existing) |
| 135 | TABLE 900mm X 600mm W/O DRAWER (Drg No FD-232) |
| 136 | Removing/taking out carefully old unserviceable worn out/components parts of the following wooden furniture, and M&L for the same as listed below with new materials/components, made to finishing to receive paint including welding if necessary to bringout the new serviceable condition all as specified, directed and shown on drawing. |
| 137 | Front rail made out of 2nd class hardwood all as specified. |
| 138 | Side rail made out of 2nd class hardwood all as specified. |
| 139 | Long Stiffener made out of 2nd class hardwood all as specified. |
| 140 | Short Stiffener made out of 2nd class hardwood all as specified. |
| 141 | Leg made out of 2nd class hardwood all as specified. |
| 142 | Removing existing worn out u/s top and S&F for new one made cut of particle board 18mm thick one side laminate of size 900mm X 600mmwith teak wood beading 4mm thick all around in its original position with required screws. |
| 143 | TABLE 900x600 WITH DRAWER (Drg No FD-1008) |
| 144 | Removing/taking out carefully old unserviceable worn out/components parts of the following wooden furniture and M&L for the same as listed below with new materials/components, made to finishing to receive paint including welding if necessary to bringout the new serviceable condition all as specified, directed and shown on drawing. |
| 145 | Leg made out of 2nd class hardwood all as specified. |
| 146 | Side rail made out of 2nd class hardwood of size 25 mm x130 mm x740 mm all as specified. |
| 147 | Removing existing worn out u/s top and S&F fornew one made cut of particle board 18 mm thick one side laminate of size 900 mm x 600 mmwith teak wood beading 4mm thick all around in its original position with required screws. |
| 148 | CHARPOY GI PLY TOP (Drg No FD-220) |
| 149 | S&F for GI Charpoy Long Rail of GI Pipe 32mm bore (dia) Medium Grade duly threaded both ends upto the required Length and fitted to frame of charpoy including taking out unserviceable long rail from 3-way elbow by unscrewing, complete all as specified/as shown on Drawing/as directed. |
| 150 | S&F for GI charpoy leg made out from LONG RAIL & SHORT RAIL (Retrieved from item No 29.01 & 29.05), duly threaded one End including 2 No Mild Steel Flat Iron 20x3mmClamps and providing Mild Steel Flat iron or Washer to Bottom of Mild Steel Clamps, Welded to Leg and treated with one coat of black paint over a Coat of Red Oxide Zine Chrome Primer including taking out unserviceable LEG by unscrewing from 3 way Elbow, completed all as specified/as shown on Drawing/as directed. |
| 151 | S&F for GIelbow 3-way, ISI Marked suitable for GI Pipe 32mm Bore (dia) of GI charpoy including taking out unserviceable GI elbow from the Frame, complete all as specified/as shown on Drawing/as directed. |
| 152 | Removing the existing u/s ply wood from GI charpoy and S&F for new plywood (07 Nos of ply) 12 mm thick BWR ISI mark. |
| 153 | S&F GI Charpoy Short Rail made out from Long Rail (Retrieved from item No 29.01 here-in-before), duly Cut and Treaded Both Ends upto the required length and fitted including Taking out unserviceable SHORT RAIL by unscrewing from 3 Way Elbow, complete all as specified/as shown on Drawing/as directed |
| 154 | S&F GI check nut, ISIMarked suitable for GI Pipe 32mm Bore (dia) of GI charpoy including taking out unserviceable GI Elbow from the Frame, complete all as specified/as shown on Drawing/as directed. |
| 155 | M&L for preparation of external and internal surface of Charpoy including derusting,grindingpaste putty ,sanding etc and applying two coats ofsynthentic enamal paint,with spray paint by compressor of Ist quality (Asian paints)duly colour approved by GE complete all as specified and directed by Engr in charge and shown on drawing. (Note: (i)Rusted poration shall be de-rusted and treated with one coat of red oxide primer before applying paint.(ii) Re-jointing by welding not exc.100mm in lenghth /Girth (Thickness of metal to be weld not Exc. 6mm) including one coat of synthetic enamal paint over a coat of red oxide primeron effected repaired/welded portion to match with existing) |
| 156 | TABLE OFFICE CLERK STEEL (Drg No. FD-1004) |
| 157 | Removing the old u/s top and S&F for new one made out of 18mm thick prelaminated particle board one side laminated (exterior grade) otherside balancing white with 4mm teak wood beading all around and fixing the same on table in its original position as per drawing and providing new hard rubber shoes to the legs. |
| 158 | Removing the worn out u/s lock from table and S&F for new lock (6 lever with duplicate key) with round shape of MS key plate as approved by GE duly fixed as shown in drawing. |
| 159 | TABLE OFFICE OFFICER STEEL (Drg No. FD-1003) |
| 160 | Removing the old u/s top and S&F for new one made out of 18mm thick prelaminated particle board one side laminated (exterior grade) otherside balancing white with 4mm teak wood beading all around and fixing the same on table in its original position as per drawing and providing new hard rubber shoes to the legs. |
| 161 | Removing the worn out u/s lock from table and supply & fixing with new lock (6 lever with duplicate key) with round shape of MS key plate as approved by GE duly fixed as shown in drawing. |
| 162 | Officer Chair with Revolving Base and Black Leather(Trade Pattern of Make -Delite ) |
| 163 | Removing the u/s broken base of officer chair with revolving baseand S&F for new Revolving baseas specified & shown on drg. |
| 164 | Removing the u/s broken Hydraulic system of officer chair with revoling base and S&F fornew hydraulic system as specified & shown on drg. |
| 165 | Removing the u/s broken wheels push type of officer chair with revolving base and S&F for new wheelsas specified & shown on drg. |
| 166 | Removing the u/s broken Arms Rest of officer chair with revoling base and S&F for new arms restas specified & shown on drg. |
| 167 | Removing the old unserviceable wornout / torn out leather cloth of officer chair with revolving base and S&F for new leather clothof superior quality as approved by GE |
| 168 | Side Chairwith revolving Base and Black Leather (Trade Pattern of Make -Delite ) |
| 169 | Removing the u/s broken basesystem of side chair and supply & fixing for new revolving base as specified & shown on drg. |
| 170 | Removing the u/s broken Hydraulic system of side chair and supply & fixing for new hydraulic system as specified & shown on drg. |
| 171 | Removing the u/s broken wheels push type of side chair and supply & fixing for new wheels as specified & shown on drg. |
| 172 | Removing the u/s broken Arms Rest of side chair and supply & fixing for new arms rest as specified & shown on drg. |
| 173 | Removing the old unserviceable wornout / torn out leather cloth of sidechair with revolving base and supply & fixing for new leather cloth of superior quality as approved by GE. |
| 174 | Cafeteria chair (Trade pattern) |
| 175 | Removing the old unserviceable wornout / torn out seat leather cloth ofcafeteria chair and supply & fixing for new seat with leather cloth of superior quality as approved by GE. |
| 176 | Sofa Chair of 3 Seater with a portion of steel Frame and cushion (Trade Pattern of Make -Delite ) |
| 177 | Removing the old u/s wornout cushion of sofa chair 3 seater and supply and fixing for new cushion 100mm thick of 40 density as per existing size. |
| 178 | Removing the old unserviceable wornout / torn out leatherfrom sofa chair 3 seater and supply & fixing for new leather of superior quality as approved by GE . |
| 179 | Sofa Chair for 2 Seater with a portion of steel Frame and cushion (Trade Pattern of Make -Delite ) |
| 180 | Removing the old u/s wornout cushion of sofa chair 2 seater and supply and fixing for new cushion 100mm thick of 40 density as per existing size. |
| 181 | Removing the old unserviceable wornout / torn out leatherfrom sofa chair 2 seater and supply & fixing for new leather of superior quality as approved by GE. |
| 182 | Sofa Chair for 1 Seater with a portion of steel Frame and cushion, (Trade Pattern of Make -Delite ) |
| 183 | Removing the old u/s wornout cushion of sofa chair 1 seater and supply and fixing for new cushion 100mm thick of 40 density as per existing size. |
| 184 | Removing the old unserviceable wornout / torn out leatherfrom sofa chair 1 seater and supply & fixing for new leather of superior quality as approved by GE for single seater |
| 185 | COMPUTER CHAIR (TRADE PATTERN OF MAKE- GODREJ),MODEL NO-PCH 50021 |
| 186 | Removing the u/s broken wheels push type and S&F for push type wheels all as specified & shown on drg. |
| 187 | Removing the u/s broken Hydraulic systemand S&F for hydraulic system allas specified & shown on drg. |
| 188 | Removing the u/s broken Arms Rest and S&F for Arms rest allas specified & shown on drg. |
| 189 | Removing the u/s broken baseand S&F for base as specified & shown on drg. |
| 190 | CHAIR CB TUBULAR STEEL WITH ARM (FD-75(M)) |
| 191 | Removing the worn out u/s cleats and S&F forthe new cleats made out of flat iron 25x3x40mm duly welded in seat frame as directed by Engr-in-Charge. |
| 192 | Removing the worn out u/s seat frame and S&F for the new seat frame one of existing size made out of 1st class teak wood duly re-caning with new plastic cane 2mm thick oval shapefor general weaving and 4mm thick plastic cane for beading all around as show in drg.Wooden frame should be finished with black polish and fix in its original position with required screw |
| 193 | All as per Srl No 39.02 above but for back frame. |
| 194 | Removing the worn out u/s handle made out of second class hardwood well seasoned and providing/fixing of exisiting size and shape with required screw after finish with black polish. |
| 195 | CHAIR CB TUBULARSTEEL WITHOUT ARM (FD-75(M)) |
| 196 | Removing the worn out u/s cleats and S&F for the new cleats made out of flat iron 25x3x40mm duly welded in seat frame as directed by Engr-in-Charge. |
| 197 | Removing the worn out u/s seat frame and S&F for the new one of existing size made out of 1st class teak wood duly re-caning with new plastic cane 2mm thick oval shapefor general weaving and 4mm thick plastic cane for beading all around as show in drg.Wooden frame should be finished with black polish and fix in its original position with required screw |
| 198 | All as per Srl No 40.02 above but for chair CB steel withoutarm. |
