|
| 1 | Dismantling of Brick tiles or terracing tiles, single layer on roofs. |
| 2 | DemolitionMud in roofs, any thickness, including plastering includingsweeping clean and washing down with water to remove dust, etc and disposal of all debristo out side MOD land complete complete all as specifed & directed. |
| 3 | Demolition of existing treatment likePCC padding including APP membrrane/plastering and leeping complete and disposal of all debristo out side MOD land complete all as specifed & directed. |
| 4 | M&L for Cutting grooves in brick wall, 75 mm wide and 65mm deep and shaping horizontal face of grove with cement mortar 1:3 complete all as specified and directed. |
| 5 | M&L for providingplain cement concrete, type B-1, 1:2:4(using 12.5 mm graded stone agg) as in roof kerbs, padding, Gola, rounded or chamfered on edges orfor leveling complete all as specified and directed. |
| 6 | M&L providing and applying the plaster with single component ready to use repair mortar capable of applying 20mm average thickness in single layer and finishing with trowel with a bond coat : SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area complete. {Make: SMART CARE REPAIR MORTAR (ASIAN PAINTS) / RENDEROC SP-40 (FOSROC) / MONOTOP F122 THEXO TROPIC (SIKA)}.Note : (a) All materials shall be procured directly form manufacturer or their authorised dealer.(b) The application shall be executed on any type of surface and on horizontal/Vertical areas. (c) Full quantity of repair mortar shall be entered in MB as \"NOT TO BE ABSTRACTED\". |
| 7 | M&L for roof treatment with polymeric membrance (APP based) with non woven polyster mat as reinforcement with following:- (a) M&L for cleaning the new plastered surface and providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.30 Ltr/Sqm on dry and clean surface.(b) M&L for providing & laying APP based polymeric membrane of 4 mm thickness of weight of 3.0 Kg/Sqm with non woven polyster fibre as reinforcement on primed surface by torch application with 15 cm end over laps & 10 cm side over laps (overlaps to be thermo fused by flame) and applying one coat of hot blown bitumen 85/25 @ 0.70 Kg/Sqm all as directed.Notes:(a) The work shall be executed through authorised applicator of manufacturer only.(b) Authrised Applicator shall be approved by GE before starting of work.(c) All materials shall be procured directly form manufacturer or their authorised dealer. (d) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a periodof Eight yearsin favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.(e) Full quantity of APP, bitumenous primer and bitumen 85/25 grade shall be entered in MB as \"NOT TO BE ABSTRACTED\". |
| 8 | Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid over and including 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including providing skirting upto 150 mm height along the parapet walls in the same manner. |
| 9 | M&L for Two coat of Aluminium paint over a coat of primer on APP membrance any description, over 10cm in width or girth,not otherwise described complete all as specified and directed. |
| 10 | Demolition of brick work built in cement mortar complete all as specified and directed |
| 11 | M & L for brick work with sub-class B brick straight or curved on plan built in cement mortar 1 : 6 complete all as specified and directed |
| 12 | Taking down cement plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc |
| 13 | M&L rendering 15mm thick in Cement Mortar 1:4 on fair faces of brick or concrete, external surfaces of walls finishedand even & fair complete all as specifed & as directed. |
| 14 | M&L rendering 15mm thick in Cement Mortar 1:6 on other than fair faces of brick surfaces of walls complete all as specifed & as directed. |
| 15 | M&L 5mm thick plastering in Cement Mortar 1:3 finished even and fair on brick & Concrete surface of ceilings complete all as specifed & as directed. |
| 16 | M&L for preparingthe newly plastered wall surface then applying2mm thick wall care putty followed by two coat of oil bound distemperover one coat of interior primer complete all as specified and directed. |
| 17 | M & L for complete removal of existing treatment from old decorated wall surface by scrapping with electric regmal machine/hand scrapper then applying 2mm thick wall care puttyfollowed by two coats of Oil bound distemper over one coat of interior primer of any tint on walls complete all as specified and directed. |
| 18 | M&L for two coat of oil bound distemper including prepration of new ceiling surface over one coat of interior primer and 1 mm thick wall care putty complete all as specified and directed. |
| 19 | M & L for complete removal of existing treatment from old decorated ceiling surface by scrapping with electric regmal machine/hand scrapper then applying 1mm thick wall care puttyfollowed by two coats of Oil bound distemper over one coat of interior primer of any tint on ceilingcomplete all as specified and directed. |
| 20 | Material & Labour for preparation of new surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 21 | M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 white cement: 1/2 coarse sand : 2 white marble stone chipping 10mm nominal size with colour compound) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed. (Note: Payment for providing grooves shall be made separately). |
| 22 | Forming groove of uniform size 15 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and directed. |
| 23 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets/wall panelling, any thickness, including cover fillets and frame worketc completeall as specified and as directed. |
| 24 | S&F Gl powder coated frame work, grid size 605x605mm, for seamless ceiling, comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, complete all as specified and as directed. |
| 25 | S&F G.I. Hangers, 6 mm dia,(up to 1200mm length) adjusting level, fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size, 60mm long and expansion hold fasteners 12.5mm dia 40mm long or ss clamp required size and shape . complete all as specified and as directed by Engr-in-Charge. |
| 26 | S&F 4.00 mm thick Non asbestos fibre cement building boards (E board) designer Pattern fixed or laid/ inserted to timber/GI/Aluminium frame work with screws complete all as specified and as directed. |
| 27 | M&L Solid PVC Wall Panelling consisting of 5 mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5mm thick PVC Sheet fillet of width 35mmfor wall panelling inclusive of fixing frame as per specification and drawing coplete all as specified and directed. |
| 28 | Dismantling floor hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and as directed. |
| 29 | M&L Vitrified Dark shade tiles 8-9mm thick (square/ rectangular) , area of each tiles not exc 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed. |
| 30 | All as per item No.29 here-in-before but on vertical surfaces over and including 10 mm thick plaster in cement mortar 1:4 complete all as specified and as directed. |
| 31 | M & L for Non-skid Coloured Ceramic tiles 7 to 8 mm thick (Square/rectangular)area of tileexc 0.11 Sqmbut not exceeding 0.18 Sqm in floors, set and jointed in neat cement to match the shade over and including 15 mm thick screed bed in CM 1 : 6 complete all as specified and as directed. |
| 32 | M & L for ColouredGlazed ceramic tiles in vertifical surface 600 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in colour cement to match over and including 10 mm th rendering in CM 1:4 complete all as specified and as directed. |
| 33 | Dismantling of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortarin floor, aprons etc and including disposal of all debrisexc 1.5 KMtr not exc 5 Km. |
| 34 | M&L 20 mm thick machine cut kota stone flooring laid over and including screed bed or bedding layer mortar 20mm thick in cement mortar 1:6 for laying floor finished jointed and pointed with grey cement slurry mixed with pigments to match the shads incl rubbing and polishing upto mirror image complete all as specified and as directed. |
| 35 | M&L 20 mm thick machine cut kota stone in riaser of steps,skirting/dado and pillar laid over and including 10 mm thick rendering coat in cement mortar 1:4 incl rubbing and polishing upto mirror image complete all as specified and as directed.. |
| 36 | M&L for 18-20 mm thick of approved shade granite stone (Zed Black) (superior Quality) slab (table rubbed and polished as in floors, jambs,steps,cooking platform,window cills & mouling on edge etc and the like, over & incl 15 mm thick screed in CM 1:4 incl pointed in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed |
| 37 | M&L for guniting of spalled/corroded reinforced cement conc surface,i.e column, beam, slab, chajja, comprising of chipping of spalled and loose conc; cleaning rust form reinforcement by sand blasting;scrubbing down conc surface with wire brushes; cleaning with water; allowed to dry and applying a layer antirust chemical of fosroc or equivalent on all exposed reinforcment followed by a layer of bonding coat of approved epoxy adhesive on complete exposed surfaces of conc to be gunited; applying two layers of guniting over steel welded wire mesh having 5mm dia of wire and aperture 50mm, total thickness of gunite not exc 60mm thick (average thickness) in cement mortar 1:2 using PPC 53 grade weight cement duly mixed with polycrete admixture @2%by weight of cement or as per manufactuerer\"s instruction and finally applying cement plaster over guinitesurfaceof required thickness to give even uniform and smooth finish conforming to proper geometrics incement mortar(1:3) to match with the existing suface as in sides and soffits etc of slabs, chajjas,fins. fascias, parapets,lintels,columns& beams etc with and incl necessary scaffolding, shuttering at any height, chases to brick work or RCC members etc, complete all as specifed and all as directed.Note-GI wire shall be insert into RCC member by doing hole then injectHILTIHIT RE 500 into the hole before guniting. |
| 38 | Taking down chowkhat or frame without taking off shutters of any description exc 1.5 sqm and n-exc 4 sqm each complete all as specified and directed. |
| 39 | Taking down chowkhat or frame without taking off shutters of any description not exc 1.5 sqmeach complete all as specified and directed. |
| 40 | Taking down shutterexc 1 sq. m and n exc 2 sq. m each complete all as specified and directed. |
| 41 | Taking down shutterexc 1 sq. m and n exc 2 sq. m each and refixing in same opening complete all as specified and directed. |
| 42 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mmprelam PVC sheetreinforced with MS Square tube, supplying & fixing in opening as per specification. |
| 43 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing. |
| 44 | S&F 35 mm thick, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. |
| 45 | S&F 35 mm thick glazed & Skelton shutter of 2nd class hard wood open rebated & prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/wire mesh etc size of members of shutters as SSR Part-I (2010),section 8,clause 8.24 (a)all as specified and directed . |
| 46 | S&Fin repair of 18/19 mm thick PVC moulded solid board one side prelam for Cup Board shutter including PVC frame with self incl provision of fixing arrangement /fixing & fixtures magnetic catches, piono hinges, knob etc) complete all as specifed and as directed |
| 47 | S&F in repairbox type Cup Board for kitchen made out of 18/19mm thick PVC moulded solid board, one side prelaminated to side, back, self and shutter, full size fitted under/ above the kitchen cooking platform and other platform including provision of all fixing arrangement /fitting & fixtures (magnetic catches, piano hinges, knob, SS Screws etc) complete all as specified and as directed. |
| 48 | S&F aluminium window as per TD DrgNo CEDZ/TD-316 with following specification : (i) Outer frame of size 40mmx114mm with 1.mm thickness, corner 45 degree cut & aluminium welded (ii) Centre mullion of size 40mm x65mm (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3 mm thickness 45 degree cut mechanically joint with 6mm allen key boult clamp with 5mm clear glass both side EPDM rubbe gasket metal body hand layer type single point lock, aluminium kobra hinges 2 No per shutter. (iv) 12mm ss 202 grade round bar . (v) Welded wiremesh sutter (2 Nos)of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges,PVC magnet & necessary fitting and locking arrangement . (vi) Entire window shall be power coated with pure polyster coat of any shde as approved by GE. (vii) Window shall be installed with silicone complete all as specified and directed by Engineer in-Charge. |
| 49 | S&F aluminium window as per TD DrgNo CEDZ/TD-316 with following specification : (i) Outer frame of size 40mmx114mm with 1.mm thickness, corner 45 degree cut & aluminium welded (ii) Centre mullion of size 40mm x65mm (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3 mm thickness 45 degree cut mechanically joint with 6mm allen key boult clamp with 5mm clear glass both side EPDM rubbe gasket metal body hand layer type single point lock, aluminium kobra hinges 2 No per shutter. (iv) 12mm ss 202 grade round bar . (v) Welded wiremesh sutter (2 Nos)of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be power coated with pure polyster coat of any shde as approved by GE. (vii) window shall have provision of for installtaion of window AC/ Desert cooler and provision of window galls shutter, wiremesh, grill and necessary fittings and locking arrangement for subject portion will be modified as per ground requirement during the execution as per directions of Engr-in-Charge. (vii) Window shall be installed with silicone complete all as specified and directed by Engineer in-Charge. |
| 50 | S&F aluminium ventilator with outer frame 40mmx114mm with 1.3mm thickness corner 45 degree cut & aluminium welded centre mullion size 41mmx65mmx1.3mm thick partly glazed /guazed including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,MS wire mess, 3mm thick sheet glass etc, provision for fixing the exhaust fan complete all as specified and directed. |
| 51 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples or powder coated aluminium beading complete all as specified and directed. |
| 52 | S&F in repair Galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staple complete all as specified and directed. |
| 53 | S&F 150 mm Aluminium handles, cast type anodised complete all as specified and directed. |
| 54 | S&F 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified. |
| 55 | S&F 200mmaluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified. |
| 56 | S&F 300mm longMild steel sliding door bolts, plate type,stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. |
| 57 | M&L for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed. |
| 58 | M&L for Onecoats of synthetic enamel painton old woodenSurfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed. |
| 59 | M&L for two coats of synthetic enamel paint over a coat of Red oxide primer on new Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed. |
| 60 | M&L for Onecoats of synthetic enamel painton old Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed. |
| 61 | Taking up or down 25mm bore steel tubingand connections, including cleaning for refixing or removal to store |
| 62 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store |
| 63 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store |
| 64 | Supplying and laying of CPVC 32 mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors all as specified complete with fitting as required. |
| 65 | Supplying and laying of CPVC 25 mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors all as specified complete with fitting as required. |
| 66 | Supplying and laying of CPVC 20mm OD pipes SDR 11 &including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including cutting chases for concealed water tubing and making good in CM 1:3including brass fittings (elbow/adoptor/tee etc) of all pointcomplete all as specified and directed. |
| 67 | S & F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) white with ‘P’ or ‘S” trap,any pattern including Seat Cover (excluding flushing cistern and flush pipe) |
| 68 | S & F in repair 10 LtrPVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets. |
| 69 | S&F in repairOne piecewhite Wash Basinwith full Pedestal fo size 560 x 415 x 820 mm complete all as specified and directed. (Make : Prayag Cat No : 4602 or equivalent in Cera/Prayag/Hindware) |
| 70 | S&F in repair 15mm bore Angle cock/ stop valve with flange, fancy type, chromium plated screwed dowen, high pressure, with fancy handle, screwed end for iron pipe or for union for 15mm bore steel tubin complete all as specifed and directed. (Make: Jaquar/Marc/Kohler) |
| 71 | S&F in PVC connection 15mm bore with Brass nuts of length 600mm |
| 72 | S&F in repair Waste coupling32mm bore dia of PTMT half threaded for WHB & Sink complete all as specified and directed. |
| 73 | S&F in repair Corrugated Waste Pipe32 mm dia for urinal complete all as specified and directed. (Make : Prayag Cat No327 or equivalent in Polytuf/ Jindal Polymer) |
| 74 | S&F in repair Corrugated Waste Pipe32 mm dia for WHB & Sink complete all as specified and directed. (Make : Prayag Cat No327 or equivalent in Polytuf/ Jindal Polymer). |
| 75 | S&F in repair facny type CP Bib Cock 15mmlong body with flangecomplete all as specified and directed. (Make: Prayag Cat No : 6508 or equivalent in Jaquar/ Marc/ Kohler) |
| 76 | S&F in repair 15 mm CP WHB mixer complete all as specified and directed. (Make: Jaquar/Marc/Kohler) |
| 77 | S&F in repairCP Soap Dishincluding chromium plated brass screws and plastic cleats complete all as specified and directed. (Make : Prayag Cat No : BA-05 or equivalent in Jaquar/Marc/Kohler) |
| 78 | S&Fin repair Chromium plated health faucet Faucet (1mtr Braided Tube) with Hook and including two way tap complete all as specified and directed. (Make: Jaquar/Marc/Kohler) |
| 79 | S&Fin repair PEG Set 6 (Zinc) complete all as specified and directed. |
| 80 | S&F in repair CP Towel Rail 600mm longfixed with and including Chromium plated brass screws and plastic cleats complete all as specified and directed.(Make : Prayag Cat No : BA-01or equivalent in Jaquar/Marc/Kohler) |
| 81 | S & F in repair glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long (Make: Jaquar/Marc/Kohler) |
| 82 | S&Fin repair corner Glass Shelf300mm (with brass brackets)complete all as specified and directed. (Make : Prayag Cat No : BEA-44 or equivalent in Jaquar/Marc/Kohler) |
| 83 | S&F in repair sink with out drainage board made of 1mm thick stainless steel, kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 84 | Supply & fix in repair 15 mm concealed stop valve chromium plated fancy type with elegant knob screwed down high pressure complete including CP long shank and cup all as specified and as directed. (Make: Jaquar/Marc/Kohler) |
| 85 | S & F in repair 80 mm dia CP Overhead Shower complete with arm. (Make : CERA Cat No : F7020310AB or equivalent in Jaquar/Marc/Kohler) |
| 86 | Dismantling water tanks exc 250 & n exc 500ltr capacity and removing to store. |
| 87 | S&F 750 ltr Rotational moulded Polyethylene water storag tank three layered (Cylindrical vertical with closed top) hoisted and fixed in position including fittings for CPVC pipe all as specified and directed. |
| 88 | S&F in repair 32 mm Ball Valve for 32mm OD CPVC pipecomplete all as specified and directed. |
| 89 | S&F in20mm bore dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwedfor iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms) |
| 90 | Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) anddisposal of all bldg materials to out side MoD land as per NGT guide line complete all as specified & directed. |
| 91 | Demolition of Chajjas (other than ground floors), beams, staircases, landing/shelfand similar suspended work. |
| 92 | M & L for RCC (Nominal Mix) type B1 1:2:4 using 20 mm graded stone aggregate as in Chajja including necessary formwork complete all as specified and directed. |
| 93 | M & L for Cement concrete type C1:3:6 using 40 mm graded aggregate as in surface channels and drains Complete all as specified and directed. |
| 94 | M &L for TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 95 | M&L 75 mm thickPCC 1:3:6, type C1, using (20mm graded aggregate) as in Plinth protection and finished the surface fair & even without using extra cement, laid in panel , including filling the joints with sand mixed with bitumen in 1:1 ration complete all as specified and directed. |
| 96 | S&F in repair WPC (Wood Polymer Composite) Jali 24mm thick of required size comprising of virgin PVC resin ofK Value 58-60 (Suspension Grade), Calcium Carbonate and natural fibers (wood Powders/rice husk/wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded with having minimum density not less than 650 kg/cbm, having good screw holding capacity Minimum comprosing of 50 N/mm2, Modulus of elasticity 850 N/mm2 and resistance of speed of flame of Class A Category with property of being termite/ borer free water/ moisture proof and fire resistance. For WPCJalli to be fixed with necessary supporting length of angle iron at vertical as well as horizontal at Bldg face/ Back at any height to be fixed with 40 x 40x6 mm GI L frame fixed with 10mm wall Anchor Boltfastener Rust Proof to wall (size of sigle L frame portion Less than 1.2x1.2m ) including painting of frame.Note:- Note : The unit rate quoted by contractor includes cost of Angle iron frame with fixing arrange ment at any height and deisign as per direction of Engr-in- Charge. |
| 97 | Dismantling wrought irom or mild steel work of any description not otherwise provided for. |
| 98 | M & L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks ,cooler stand, chowkat, Chajja and similar work conforming to Fe.290.Gde-E-165 |
| 99 | M&L forcement concrete type B1 1:2:4 using 20mm graded stone aggregateas in coping,kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates complete all as specified and directed.. |
| 100 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) |
| 101 | PVC (SWR) 75 mm borepipes single socketed in any length with rubber ring joints fixed to walls |
| 102 | S&F PVC (SWR) 75 mm bore pipe single socketed, in anylength with rubber ring jointes , laid in trenches or in floor complete all as specified and directed. |
| 103 | S&F PVC (SWR)110 bore pipe single socketed, in anylength with rubber ring jointes , laid in trenches or in floor complete all as specified and directed. |
| 104 | S&F PVC (SWR)110 bore pipe single socketed, in anylength with rubber ring jointes ,fixed to wall complete all as specified and directed. |
| 105 | S&F PVC (SWR) floor trap 75 mm dia, plain with grating including jointing with solvent cement complete |
| 106 | S&F 75mm borePVC (SWR) vent cowl |
| 107 | S&F 110 x 75 mm PVC (SWR) reducers |
| 108 | S & F SS clamps heavy duty of 25 mmx 3 mm thick fixed by 8mm fastener for fixingPVC Pipe of 75 mm boreto wall or roof copletet all as specified and directed. |
| 109 | S & F SS clamps heavy duty of 25 mmx3 mm thick fixed by 8mm fastener for fixingPVC Pipe of 100 mm boreto wall or roof copletet all as specified and directed. |
| 110 | S&F 110 mmPVC (SWR) junction single,(Single T) equal or unequal with access door. |
| 111 | S&F75mmPVC (SWR) junction single, (Single T) equal or unequal with acces door. |
| 112 | S&F 110 mm bore PVC (SWR) bends any radius |
| 113 | S&F75 mm bore PVC (SWR) bends any radius |
| 114 | Cutting and taking outplants, tree roots from Md Accn bldgs in any position and height and treated with necessary chemical/acid to avoid for this growth and making good the disturbed portion with PCC 1:2:4 type BO including finishing etc complete all as directed and specified. (Note: The cost of scaffolding required for repairs is deemed to be in the quoted rate by the Contractor). |
