|
| 1 | Tarring works |
| 2 | 3.5.2:Excavation in Soil with Dozer with lead upto 100 mExcavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. |
| 3 | 3.2:Preparation of Foundation for EmbankmentScarifying Existing Bituminous Surface to a Depth of 150 mm by Mechanical MeansScarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4. |
| 4 | OD399798/2024-2025:(OD from DAR 51.2.3)Filling with Quarry MuckFilling up low lying and water logged areas with local material/ quarry muck, spreading in layers, levelingthe top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade |
| 5 | 4.9:Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406.By Mechanical Means with 1 km lead |
| 6 | 5.1.1a:Prime Coat :- Low porosityProviding and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 |
| 7 | 5.2.3a:Tack Coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503. |
| 8 | 5.5.A.1a:Modified Penetration Macadam 50 mm thick using Bitumen S-65Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. |
| 9 | 5.2.1a:Tack Coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. |
| 10 | 5.11.1.A.2a:Mix Seal Surfacing - Manual Means - Type A - Bitumen S-65Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509By Manual Means :- Type A(II) Bitumen (S-65) |
| 11 | OD434834/2024-2025:Providing and fixing of Direction and Place Identification retro reflectorisedsigns with 7 years warranty manufactures as per IRC : 67 made of type IV micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick /aluminium composite material sheeting 4mm thick witharea exceeding not exceeding 0.9 sqm, with suitable back supporting frame of MS angle 40*40*6mm andsupported on GI pipe pole 50mmNB-2nos confirming to IS 1239firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete min size 40 cm x 40 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer andas per approved drawing and Technical Specification Clause 801 including lettering symbols etc (Derived from Mord spec 10.3.A. 2 |
