Construction Of Indoor Stadium Complex In Ward No. 23 At Medininagar
Tender Value
4.73 Crore
Estimated cost
Bid Submission
14 Feb 2025
0 days left
EMD
4.73 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
medininagar → Jharkhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
construction Of Indoor Stadium Complex In Ward No. 23 At Medininagar
BOQ
| Sl. No. | Item Description |
| 1 | Item Description |
| 2 | Earthwork in excavation in foundation trenches in ordinary soil(vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 m includingall lifts, levelling , ramming the foundation trenches, removing roots of trees, serbs all complete as per approved design, building specification & direction of E/I. |
| 3 | Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and 1.5M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume) |
| 4 | Providing designation 75B one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 8 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 9 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing andreinforcementwith 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 10 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but, excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for : Weather shade, Chajjas, corbels etc., including edges |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 18 | Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral-staircases |
| 19 | Providing TMT reinforcement of following dia rods as per approved design and drawing including carriage of M.S. rods of (Straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.( i.) 8 mm dia (19 %of total reinforcement) |
| 20 | 10mm dia(17%of total reinforcement) |
| 21 | 12mm dia(17%of total reinforcement) |
| 22 | 16 mm dia(17 % of total reinforcement) |
| 23 | 20 & 25 dia(30 %of total reinforcement) |
| 24 | Providing and mixing liquid integral water proffing compound in conctrete of plaster as manufacturer specification and as per direction of engineer in charge. Brand. Sika plastocrate plus, MYK proff WP 10, Fosroc- Conplast x 4211C, Dr.Fixit, Pidiproff LW+ or Equivalent |
| 25 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mmdia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing. |
| 26 | Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressedwith earth obtained from excavation foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 27 | Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume). |
| 28 | Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 29 | Providing 25 mm thick damp proof course with cement concrete M-200 with nominal mix of (1:1½:3) with approved quality of stone chips of 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including, screening, shuttering and mixing cement concrete in mixer with 5% cico or any other approved water proofing compound and placing in position, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.. |
| 30 | Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\" x 4.5\" x 3\") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 31 | Providing 112mm thick reinforced designation Flyash brickwork in C.M. (1:4) in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 32 | Extra brick work for each consecutive floor above first floor including watering and scaffolding all compleat as per direction of E/I |
| 33 | Providing 12mm thick cement plaster (1:6)with clean coarse sand of F.M. 1.5 and including cost of screening, curingwith all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I |
| 34 | Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I. |
| 35 | Extra for plaster work exteriour surface for each consecutive floor above first floor including cost of scaffolding ect all complete as per direction of E/I |
| 36 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 37 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete. |
| 38 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 39 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 40 | Providing and laying Double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less then 0.08% and conforming to IS: 15622/ISO 13006 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 Coarse sand0, jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with wite cement and matching pigments etc, complete Size of tiles 600 x 600 mm. |
| 41 | Granite stone slab colour black, Cherry/Ruby Area of slab upto 0.50 sqm |
| 42 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000 mm |
| 43 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 1000x1000 mm |
| 44 | 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class teak wood |
| 45 | Supplying, fitting and fixing good quality ,well dressed and well seasoned sal wood work in chuakhat in doors, window skylights, fanlights and C/W celetialwindowopenings,including wedge over all clamps complete including application oftwo coats of wood prese- |
| 46 | Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes |
| 47 | Providing and fixing PVC igid form sheet 1mm thick on existing door shutters (bthroom and WC doors) using synthetic rubber basedadhesive |
| 48 | Supplying, fitting and fixing steel gate with 16mm dia M.S bars at 15cm centres with spear shaped top ends projected 225mm beyond frame fitted on 40x40x6mm M.S. Angle frame of size 60x60x6mm including cost of fabrication, providing necessary locking arrangements with haskel and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying priming coat of red lead over steel work, taxes all complete as per drawing, specification and direction of E/l. |
| 49 | Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l. |
| 50 | Supplying, fitting & fixing M.S. Grill made of 20x6mm flat as per approved design and drawing aproperly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.@window area x 15 kg/sq.m. |
| 51 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron |
| 52 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness |
| 53 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 54 | Prividing French spirit polishing over new wooden surface to give desired texture and gloss with apporoved make and shade of ready mixed french polish including preparing the surface sfter cleaning removing dirt |
| 55 | Providingprimer onecoat of red lead paint of approvedmake over steel surface including preparing the surface after cleaningremoving dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification direction of E/I. |
| 56 | Providing 2 coats of Synthetic Enamel Paint of approved shade and make over steel surface grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I. |
| 57 | Water proofing for old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flextble material brush, roller or spray for water proofing coating per manufacturer Specifications with following steps :-(a)surface preparation .-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing (loose paint / coating, and cement laitance by cleaning with compressed air water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage leakage. On identification of seepage cement grouting to be donewith non shrink expanding admixture of Sika India Pvt.L.td.) MYK Schomberg / Dr Fixiti/ Fosroc or equivallent. Providing and reparing of all Corner and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150Mrn X 150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic pc?\" lymer of Sika/ Fosroc/MYK Schomberg/Dr1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent.,Befor \"Chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an |
| 58 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 59 | Covering of treated surface with PCC:-providing 25 mm thick Cement Concrete M20 (1:1:5:3) maintaining slope in alternate 2 mtx 2mt panels With approved quality of stone chips of 20mm to 6 mm size graded andCleaned sand of F.M.2.5 to 3 including screening, shuttering, and mixing Cement concrete in mixer with admixture of integral water proofing and Placing in position, striking curing, taxes and royalty all complete as per Building specification and direction of E/I. Panels that has been left should Be casted next day. There should be 6 mm gap between panels .brand-Sika _ plastocrate plus, MYK proof WP 10, Fosroc- ConplastX 421 ic Dr Fixit Pidiproof LM+ same as water proffing area |
| 60 | Providing & fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. Single socketed pipes. 110mm dia |
| 61 | Providing & fixing on wall face unplasticised- PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion Bend-110 mm |
| 62 | Shoe - 110mm |
| 63 | Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plgs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 64 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. SAME AS CEILINGPLASTER AREA |
| 65 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 66 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 67 | Providing two coats of oil bound distemper of approvedmake & shadeover a coat of cement primerovernewsurface including preparing the plastered surface by rubbing, smooth with pumic stone or fine sand paper, aplying putty wherever required,scaffolding , washing of flores and taxes etc. all complete as per building specification direction of E/I. |
| 68 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 69 | Extra for providing edge moulding to 18mm thick marble stone counters,Vanities etc. over Item No. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work |
| 70 | Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l. |
| 71 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. Total area till Brick Drain |
| 72 | Providing and fixing stone slab with table rubbed, edges rounded and polished,of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. |
| 73 | Cairage Of Meterial Earth1 Km |
| 74 | Sand (10) KM |
| 75 | Aggregate 10 KM |
| 76 | Brick(7+1) KM |
| 77 | Fly Ash Brick 15 KM |
| 78 | MS. Fabricator Work |
| 79 | Labour Charge & Fitting Goods |
| 80 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 81 | Providing brick flat soling all complete |
| 82 | Providing P.C.C. (1:2:4) in subbase all complete |
| 83 | Providing 75A Brick work in foundation all complete |
| 84 | Providing 125mm thick brick work in partition all COST |
| 85 | Providing 1.5mm cement punning all cost complete |
| 86 | Supplying C.I. Cover 600X450MM (Wt. 25 kg) - 4 nos. |
| 87 | Making soak pit 2.5M diameter 3. Metre deep with |
| 88 | Providing P.C.C.M150 in normal mix of(1:2:4) in foundation with approved quality of stone metal grade II (50mm to 25mm size) clean coarse sand toF.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I |
| 89 | Providing R.C.C.M 200 (1: 1.5: 3) in foundation and plinth with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and directionof E/I |
| 90 | Providing R.C.C.M 200 (1: 1.5: 3) in Band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and directionof E/I |
| 91 | Providing designation 75A brick work inC.M (1: 6) in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 92 | Providing two coat of snowcemof approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I. |
| 93 | Extra for earthwork in hard soil as per specification and direction of E/I |
| 94 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 95 | Wall (any thickness) including attached pilasters, butteress,plinth abd string couress etc. |
| 96 | Providing designation 75B work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints of screening materials, scaffolding, ranking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 97 | Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge: |
| 98 | Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.Group-C |
| 99 | Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size of GI box etc as required. |
| 100 | Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required. |
| 101 | Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiringalong with earth wire with thefollowing sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required .2x1.5 Sqmm + 1x1.5 sq.mm earth wire(for Single Separate 5A socket from nearest switch board) |
| 102 | 2x2.5 Sqmm + 1x2.5 sqmm earth wire (for switch board circuit). |
| 103 | 4x6 Sq.mm + 2x6 Sq.mm earth wire. ( to be used a smain for Light TPN DB.) |
| 104 | 4x10 Sq.mm + 2x10 Sq.mm earth wire. ( to be used as main for Power TPN DB.) |
| 105 | TV cable in Existing Conduit:-Supplying and drawing, co-axial TV cable RG-6 grade copper conductor, PE insulated with PVC sheath in the existing surface/ recessed steel / PVC conduit asrequired. |
| 106 | S/F PVC Conduit:Supplying and fixing of following sizes of Rigid 2 mm thick PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for 20 mm |
| 107 | S/F Modular type Switch / Socket:- Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections butexcluding modular plate etc as required. (tobe used in switch board with 5/6 amps, one way modular switch |
| 108 | 5/6 amps, 3 pin modular socket |
| 109 | TV antenna socket outlet |
| 110 | S/F Modular type electronic fan regulator:- Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plateetc as required. |
| 111 | S/F Modular blanking plate:- Supplying and fixing of the existing modular plate and switch box excluding modular plate etc, as required. |
| 112 | S/F Modular boxes, base and cover plate:- Supplying and fixing following size /modules G.I. box along with modular base and cover plate for modular switches in recess etc. as required 1 or 2 modules (78mmx78mmx45mm) |
| 113 | 6 modules (78mmx140mmx50mm)(to use 2 No. 5/6A sockets & 2 no. 6 A Switch) |
| 114 | S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required. |
| 115 | S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as |
| 116 | S/F Ceiling Rose:- Supplying andfixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 117 | Erection on incandescent light fitting :- Erection of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS amps per fitting, complete with all accessories including connectionetc as required. |
| 118 | ITC fluorescent fitting directly on surface:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 119 | ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required. |
| 120 | ITC Exhaust Fan upto 450 mm sweep:- installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage,including connection, testing, commissioningetc as required. |
| 121 | DISTRIBUTION BOARD & MCB/RCCB S/F SP MCB DB:-Supplying and fixing following way,SP&N MCB distribution board of sheet steel for 240 Volts on surface /recess complete with tinned copper bus bar, neutral busbar, earth bar, detachable gland plate, interconnections, phophatized and powder coated painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). 8 Way Double Door |
| 122 | S/F TP MCB DB: Supplying and fixing following way,three pole and neutral sheetMCB distribution board, 415 volts on surface/recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). 8 ways (4+24) Double Door. (horizontal type) |
| 123 | S/F \"C\" series MCB:-Supplying and fixing 240 volts, \"C\" series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required. 6/32A Single Pole |
| 124 | 40A DP MCB (To use as incomer for all SP MCB DB) |
| 125 | 50/63A TPN (To use as incommer for all TPN D.B.) |
| 126 | P/F MV Danger Notice Plate:- Providing and fixing M.V. danger notice plate of 200mmX150mm, made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in the single red colour on front side as required. |
| 127 | Earthing with G.I. Earth plate 600mm x 600mm x 6mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal and salt as required). |
| 128 | Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required. |
| 129 | Providing and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc, as required. |
| 130 | Supplying and laying 25 mm x 5 mm G.I. strip at 0.50 meter below ground as strip earth electrode including connection/termination with G.I. nut, bolt, spring, washer etc, as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm) |
| 131 | Providing and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc as required. |
| 132 | Providing and fixing 25mm x 5mm copper strip on surface or in recess for connection etc. as required. |
| 133 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required. |
| 134 | Providing and fixing 4.00mm dia copper wire on surface or in recess for loop earthing etc, as required. |
| 135 | Earthing with G.I. Earth pipe 4.5 mtr long. 40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal and salt as required). |
| 136 | LV / MV CABLE LAYING Laying of one number PVC insulated and PVC seathed /XLPE power cable of 1.1 KV grade of size not exceeding 35 sq.mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. |
| 137 | Laying of one number PVC insulated and PVC seathed /XLPE power cable of 1.1 KV grade of size not exceeding 35 sq.mm but not exceeding 95 sq.mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. |
| 138 | SITC of floowing rating LED Street lighting luminarie with pressure die cast housing and toughtened glass cover (IP 66 protection) inexisting pole/ pipe for supply voltage 100-270V AC, 50Hz. Luminarie shell be confirm to IS:10322 patr-5/ Section-3 and shell be complete with all neccssary accessories as required.Make:- Jaquare / Havells/ Wipro/Baja. 90/100W LED Street light |
| 139 | SITC of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughtened glass cover (IP 66 protection) in existing pole/ pipe for supply voltage 100-270V AC, 50Hz. Luminarie shell be confirm to IS:10322 part-5/ Section-5 and shall be complete with all neccssary accessories as required.Make:- Jaquare / Havells/ Wipro/Baja. 200W LED Flood Light |
| 140 | SITC of floowing rating reccess/ surface mounted LED Round/ square shape Down light luminarie with pressure die cast housing for singal phase supply voltage. Luminarie shall be confirm to IS:10322 part- 5/second-2 or IEC:62722 with all neccssary accessories as required. As per the standard cataloge item.Make:-Jaquare / Havells/ Wipro/Baja. 12W LED Round Down light (Surface) |
| 141 | 15/16W LED Round Down light (Reccess) |
| 142 | Supply of surface/ pendent mounted with chain Batten type LED 4ft Tube light fitting with Housing & cover made up of CRCA sheet steel. Cover is fixed to the housing by means of 2 Nos. bolt with engineering plastic head along with 1 nos LED tube of 20/22W Each of luminous efficacy of efficacy >110 Lm/W. Make:- Jaquare / Havells/ Wipro/Baja. |
| 143 | SITC of following rating LED Post top lamp made in die cast aluminium housing with decorative clear/ opal acrylic diffuser on existing pipe including connection with 1.5sq.mm. copper conductor etc all complete as required.As per the standard cataloge item.Make:-Jaquare / Havells/ Wipro/Baja. 40/45W LED Post top lamp clear |
| 144 | SITC of following rating approved make LED Bollard fitting with rectangular shape of height 600 to 850mm power input 8/9Wall with die cast aluminium housing opel with PC diffuser, IP:65/54 protection, confirming to IS:10322 part 5 etc all complete as required. (excluding plinth charge)Make:-Jaquare / Havells/ Wipro/Baja. |
| 145 | FANS & Exhaust FANS Supply, Installation, testing and commissioning of following, size ceiling fan 3 Blades confirming to IS : 374 : 2019 including wiring the down rods of standard length (up to 30cm) with 1.5 sq.mm. FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required. 1200mm (48\") BLDC 5star rating 32W Ceiling Fan |
| 146 | Supply, fitting and fixing of Special type bulk head fittings complete set with 9W LED.Make:- Jaquare /Havells/ Wipro/Baja. |
| 147 | Supply of double LED Tube light Fitting made of diacast aluminium housing 2x20W LED Bettle Tube light sritable for surface or suspended mounded suitable for 230V, 50 Hz, single phase supply etc all complete as required,complete with electronic diver and LED etc., including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. Efficacy is 100 lm/W.temperature (5700K ± 355K. The Average life of 50000 burning hrs @L70 & Lumen maintenance as per L70 (Confirming to I.E.C. 62722)Make:- Havells/Philips/Crompton/Wipro.(Make :-Philips-/Havells / Equivallent inBajaj / Wipro.). |
| 148 | Supply and Transportation of AC 230/250 Volts, 50Hz,300mm sweepExahaustFans including providing nuts- bolts, mounting frame and other required accessories etc. (For toilets) Make:- Bajaj /Crompton/ Havells . |
| 149 | Air Circulator Turbo Wall Fan :- Supply, fitting, fixing and testingof Air Circulator Turbo Wall Fan 450mm 230V/1440rpm heavy duty with metal blade along with front metal net and proper stand to be installed in the wall of main auditorium hall. Make:- Havells/Bajaj/ Crompton. |
| 150 | Supply of100 Watt Suspennded type industial COB LED highbay light with aluminium die cast heat sink(Make :-Philips-/ Havells / Equivallent inBajaj / Wipro.). |
| 151 | Providing and fixing of PVC/XLPE indulated PVC sheathed heavy duty , aluminium armoured cable of grade 1.1KV as per IS 1554 (Part-1), etc. as required. Make:- Havells / Finolex / Polycab/KEI. 2 Core 6 Sq.mm. XLPE Al. Ar. Cable 1.1kV. |
| 152 | 4 Core 10 Sq.mm. XLPE Al. Ar. Cable 1.1kV. |
| 153 | 3.5 Core 50 Sq.mm. XLPE Al. Ar. Cable 1.1kV. |
| 154 | Supplyof 7 Meter Height Octagonal Hot Dip Galvanized pole (BOP 7030) with top dia 70mm bottom dia 130mm & made of 3 mm thickj sheet, base plate dimensions 200x200x12mm (L X B X T) including suitable sizes offoundation bolts all complete as required. (Without ARM) Make:- RR Ispat/ Transrail/ Valmount/Bajaj. |
| 155 | Installation, Testing and commissioning of 7 Meter Height Octagonal Hot Dip Galvanized pole with suitable Tools and Plants, wiring ofLuminaires with all materials and construction of shallow foundation, with M25 grade concrete considering safe soil bearing of 10T/mtrs Sq. |
| 156 | Supply fitting, fixing of Double Arm (1.5 Mtr. Long) suitable for 70 mm Top.Make:- RR Ispat/ Transrail/ Valmount/Bajaj. |
| 157 | Supply of Conical pole of height 3 mtr with top dia 75 mm ,bottom dia 105+_5 mm , sheet thickness 3 mm and base plate 200 x200x 12 mm with PU painted in different colour as required. Top.Make:- RR Ispat/ Transrail/ Valmount/Bajaj. |
| 158 | 3000VA sin€ wave inverter input AC renge-100v to 300V AC, wide- 90V to 300V AC, standard - 180V to 260V AC, DC range - 10.5 to 14.2 efficiancy- 80%, protection-overload, Short circuit,Make:- Microtek/v- GUARD |
| 159 | Trolly for Double tubular Battery,Make:- Microtek/v- guard |
| 160 | 200Ah tubular Lead acid battery with 36 month replacement guaranty. IS:1652:1991,Make:-Excide/Microtek |
| 161 | 2 Tr. 5 Star Split A.C (Inverter Type) I91391-part- II,Make-CATEGORY \"B\" (Mitsubishi heavy industries and O\"GENERAL) |
| 162 | Copper Tube of size1/4\" for spilt ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation. |
| 163 | Copper Tube of size5/8\" for spilt ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation. |
| 164 | 5 KVA wall mounted automatic voltage stablizer from range 140 V to 280 V. |
| 165 | Outdoor stand for 2.0 Tr. Split AC. |
| 166 | 50 KVA Silent D.G. Set :- 50KVA DG set with AMF Panel IS/IEC - 60034-1, IS:1460, IS:13018 :- Cost of 50 KVA DG set with AMF Panel |
| 167 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 1 run of Cable |
| 168 | Supplying and fixing 20 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 amps \"C\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 169 | Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps \"C\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 170 | 1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required. 2 X 6 sq. mm (19mm) |
| 171 | 4 X 10 sq. mm (25mm) |
| 172 | 3½ X 50 sq. mm (35mm) |
| 173 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc. as required 100 mm dia |
| 174 | 4 pole MCCB 200 A,16 kA with fixed thermal magnetic setting. |
| 175 | 4 pole MCB 40 A,10 kA with fixed thermal magnetic setting. |
| 176 | 4 pole MCB 63 A,10 kA with fixed thermal magnetic setting. |
| 177 | 40 A,DP |
| 178 | 300 amp 415 V heavy duty three phase with neutral bus bar chamber. |
| 179 | 200 amp,4 Pole 415 V ,Change Over |
| 180 | Supply and fixing fabricated Feeder pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dustand vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator, with 40mm X 40mm X 5mm angle iron stand and complete in all respect etc and must be CPRI approved panel manufactures. (But without RYB LED lamp, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears, PCC work etc.) |
| 181 | Electronic timer-on delay/off delay for 0 to 30sec. |
| 182 | Auxiliary contactor (1NO +1NC) of following rating 32amp IS/IEC/60947-4-1 |
| 183 | Indicator switch R/Y/B |
| 184 | 3 Way 4 pole selector switch |
| 185 | Digital Volt Mtr (0-500 Volt) 3 Phase class 0.5 |
| 186 | Digital Amp Mtr (0-500 Volt) 3 Phase class 0.5 |
| 187 | C.T Coil of C.T ratio200/5 IS :2705 part -3 |
| 188 | 50mm x 5 mm copper tape (2.30 kg/mtr) |
| 189 | 20mm x 3 mm copper tape (0.533 kg/mtr) |
| 190 | 10 SQ MM ISI Marked FRLS PVC insulated , single core copper conductor cable |
| 191 | 6 SQ MM ISI Marked FRLS PVC insulated , single core copper conductor cable |
| 192 | 2.5 SQ MM ISI Marked FRLS PVC insulated , single core copper conductor cable |
| 193 | 1.5 SQ MM ISI Marked FRLS PVC insulated , single core copper conductor cable |
| 194 | Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (Without MCB/RCCB/ISOLATOR). 6 Ways double door |
| 195 | 40A TPN MCB |
| 196 | Supply and Transportation of 1200mm Sweep, double ball-bearing, 2 canopy ceiling fan without regulator including connection with 1.5 sq mm copper wire, down rod all accessories as required. Make :- Bajaj / Crompton / Havells. |
| 197 | S/F BUSBAR CHAMBER :- Providing and fixing following capacity 2 pole /4 pole ON/OFF Load Changeover switches with side handle operation in sheet enclosure inexisting metal board incuding driling holes in metal board making connection earthing the body etc as required. 100 Amps,4 Pole |
| 198 | S/F sheet metal ON/OFF Load Changeover:-Providing and fixing following capacity 2 pole /4 pole ON/OFF Load Changeover switches with side handle operation in sheet enclosure inexisting metal board incuding driling holes in metal board making connection earthing the body etc as required.100 Amps,4 Pole |
| 199 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc |
| 200 | Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of \"Hindustan\" \" Parry\" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l. |
| 201 | Providing and fixing C.P. brass bib cock of approved conforming to IS 8931 : 15 mm nominal bore |
| 202 | Providing and fixing C.P.brass long body bib cock of approved quality conforming to standard and weight not less thain 690gms.:15 mm nominal bore. |
| 203 | Providing and fixingPTMT Soap Dish Holder having length of 138 mm breadth 102 mm, height of 75mm with concealed fitting arrangements, Weighing not less then 106 gms. |
| 204 | Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings. |
| 205 | Providing and fixing C.P. extentsion Nipples 15mm size with 12” BSP threads, 70mm length and 30 mm bredth and weight not less than 18gms |
| 206 | Providing and fixing Mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing.Circular shape 450 mm dia |
| 207 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever require :Falt back wash basin size 630X450 mm with a single 15mm C. P. pillar tap. |
| 208 | Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole |
| 209 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length |
| 210 | Providing And fixing 32 mm waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 211 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL/ SUPREME) Concealed work including cutting chases and making good the wall etc. 15mm dia |
| 212 | 20mm dia |
| 213 | Exposed on Wall 25mm dia |
| 214 | 32 mm dia. |
| 215 | 40mm dia |
| 216 | Supllying and matarials with lobour for construction inspection chamber of designation class 75b brick deep 600x450 internal diamention having 250mm wall thickness in cement morter(1:6)including 12mm cement plaster (1:4)with punning on inside and cement plaster (1:6)with 600x450mm G.I. cover with frame (weight not less than 36k.g)in foundation and refilling all complete as per specification and direction of E/I. |
| 217 | Providing and fixing C.P. brass Stop Cock (concealed) of standard designand of approved make conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings. |
| 218 | Providing and placing on terrace (at all floo levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and marking necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank. |
| 219 | Providing and fixing c.p. towel Rail complite with brackets fixed to wooden cleats with c.p.brass screws with concealed fitting arangement of approved qualite colour and make.(Mark or equipment) |
| 220 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 221 | provding and laying of 110mm dia. P.V.C. pipe for outlet of water to outlet drain including all accessories ,I.e lubricants, solventcement, clamp, ring, sockets etc.(SUPREME S.W.R.) |
| 222 | provding and laying of 75 mm dia. P.V.C. pipe for outlet of water to outlet drain including all accessories ,I.e lubricants, solventcement, clamp, ring, sockets etc.(SUPREME S.W.R.) |
| 223 | i) 110 mm Door Tee (Supreme) P.V.C. |
| 224 | ii) 110 mm Plain Bend (Supreme) P.V.C. |
| 225 | iii) 110 mm Door Bend (Supreme) P.V.C. |
| 226 | iv) 110 mm 45 degree offset(Supreme) P.V.C. |
| 227 | vi) 110 mm Plain Trap (Supreme) P.V.C. |
| 228 | i) 75 mm Door Tee (Supreme) P.V.C. |
| 229 | ii) 75 mm Plain Bend (Supreme) P.V.C. |
| 230 | iii) 75 mm Door Bend (Supreme) P.V.C. |
| 231 | iv) 75 mm 45 degree offset(Supreme) P.V.C. |
| 232 | vi) 110 mm Plain Trap (Supreme) P.V.C. |
| 233 | Suppling all materisls labour and tools and equipment for drilling 200x150mm dia bore well in any kind of sell rock by using D.T.H supper rig machine and bell hammer tecjnology inclusive of mabillisation de meblizationof rigs air compressor all accesseries tools and plant labour etc. all complete job includingtransportation charge etc. From 0.0M to 50.0 M belew G.L |
| 234 | From 50.0 M to200.00 M belew G.L |
| 235 | supplying all naterialals labour and in serting M.S pipe 200mm internal dia (Made with 6mm thick M.S plate )casing pipe for protecting the bore holein over burden up to hard surface depth inclouding scaling all expencitrue and grouting casing pipe etc. all complete job as per direction of E/I. |
| 236 | Cleaning Flushing and devloping of drilled hole for testing the discharge of water development of bore well by continueous flow of water bu using heavy compresser upto satisfaction of E/I. To get uninterrupted flow of water free from sand and soil etc. |
| 237 | Supplying and fitting M.S cap over 200mm dia casing pipe as per direction of E/IFor safety of drilling bore including providing of guard for safety of the same till returned final. |
| 238 | Cost of supply of submersible pump set ( 2 HP) ata head of Less 20 m of total Depth Borewell single phase sutitable of 6\" Tube well all complete job. |
| 239 | Supplying complete panneal boarad with all accessories (starter 1 no, vot meter 1 no, amp meter 1 no,100 amp kit kat( male & female) all complete job. |
| 240 | Cost of 4mm 2 flate copper cable finolex make for lowering the pump & connection upto pannel bord with all complete job. |
| 241 | 2no heavy duty clamp 40mm dia duitable for pipe with all complet job. |
| 242 | Supplying & lowering 40mm da column PVC pipe with all complete job. |
| 243 | Shed Arae (GI Colour Coated Roofing Sheet Make Jindal & Hollow Pipe Size 50x100 mm As Per Design) |
| 244 | Providing & injecting chemical emulsion for pre- construction Anti termite treatment and creating a chemical barrier under and all around the column pits wall treanched basement excavation top surface of plinth filling junction of wall and floor along the external perimeter of building with apporoved chemical as per IS coad as per specification and direction of E/I |
| 245 | pandanus |
| 246 | Heliconia metallica |
| 247 | Sygizium small |
| 248 | Red note plant |
| 249 | spider lily |
| 250 | Murayya exotica |
| 251 | Ficus panda |
| 252 | Areca palm |
| 253 | foxtail plam |
| 254 | spathodia |
| 255 | lagestromia |
| 256 | Delonix regia |
| 257 | Tabebuia rosea |
| 258 | Cassia fistula |
| 259 | Maxican grass |
| 260 | 5 LAYER SPORTS FLOOR WITH 3MM(+/-.5 MM) CUSHION LAYER |
| 261 | Basketball pole ploe made of 6\" dia pipe with 2.2 meter projection and basketball board transparent acrylic imported 20mm thik size 180cm x 105cm with dunking ring net and fram ring is bolted through the backboard into the main frame construction for extra strength and durability sude of branded MRF expoxy paint (B.B.6.2.2.20) (Pair) |
| 262 | Made of 3\" X 4\" mild Steel pipe height adjustable with inside special ratchet system for tightning the net This enables perfect tension control for the net Use of branded MRF Epoxy Paint (Pair 15120) |
| 263 | Supply and fixing HSE-SAS-15 Ltr (Vertical) Geyser - do- -do- all complete |
| 264 | Hand shower (health faucet) with 1 meter do- -do-all complete job |
| 265 | Providing & Fixing of Sink Mixer Swim Make Jaquar |
| 266 | Providing and fixing ball valve (full brass, KEC / APAR/ ZOLLOTO make) all complete . B)32mm nominal bore, |
| 267 | Bobbin Wound Filter Dia 900 With 02\" MPV & 03 Pcs Unions |
| 268 | Filter Media-Sand (In Killograms) |
| 269 | Automatically Offline Chlorine Feeder- 04 Kg Bucket |
| 270 | Chlorine 90% Granuals 50 Kg Drum |
| 271 | 27 m3 Nano Tech UV-C & Ozone NT-UV87-T |
| 272 | Floor Inlet ABS |
| 273 | Main Drain Frame 300 mm * 300 mm |
| 274 | Suction Inlet-Vacuum |
| 275 | PVC Wall Conduits 300 mm |
| 276 | Adjutable Standard Body Jet |
| 277 | Spa Air Controller |
| 278 | Spa Suction Drain |
| 279 | Pneumatic Press Button |
| 280 | Pneumatic Switch |
| 281 | Spa Plastic Tube In Meters |
| 282 | Air Blower 2.2 kw |
| 283 | SS Ladder 2 Step AISI 304Handrails Dia 42 mm |
| 284 | SS Ladder 3 Step AISI 304Handrails Dia 42 mm |
| 285 | SS Ladder 4 Step AISI 304Handrails Dia 42 mm |
| 286 | Ball Valve 50 mm Dia |
| 287 | Ball Valve 63 mm dia |
| 288 | Ball Valve 75 mm Dia |
| 289 | Non Returning Valve Dia 50 mm |
| 290 | Non Returning Valve Dia 63 mm |
| 291 | Non Returning ValveDia 75 mm |
| 292 | Vaccum Head 18\" Alumuniam Vacuum Head With 04 Wheels |
| 293 | Vaccum Hose 1.5\" - 30m |
| 294 | Telescopic Pole 6.0M Long |
| 295 | Curved Brush |
| 296 | Deep Leaf Net |
| 297 | Test Kit |
| 298 | Selfpriming Pump 3HP /Single phase (02 Working + 01 Stand By) |
| 299 | Selfpriming Pump 3HP /Single phase (02 Working)- Jacuzzi |
| 300 | SS 304 U/W RGB LED Light 36 W/12V In Steel (12 * 3W)- Wall Mounted |
| 301 | Cable Conduit |
| 302 | Junction Box in ABS |
| 303 | SMPSIncluding RGB Remote & Pannel Including 04 Core Wire |
| 304 | Supply & Installationof uPvc Pipes & All Fittings |
| 305 | Supply & Installation of Control Panel and Cables |
| 306 | Installation, Testing & Commissioning Of Swimming Pool Eqipment |
| 307 | Consultancy and Supervision of the Pool Civil Project |
| 308 | Cabling Tray & Piping Tray With Angle At Plant Room |
| 309 | Add 18% GST |
| 310 | Labours Cess 1 % |
AI Tender Summary
Tender Timeline
Feb 06, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 14, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 15, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender