Tender For Remaining Repair And Finishing Work In Aashray-3 Of Sulabh Awas Yojana Under Sharda Nagar Yojana - Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. DSR No. 2.6.1 2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size). DAR No. 4.1.8 3 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) DAR-2023/ 5.1.2 4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand) DAR No. 6.4.1 5 Painting or vanishing on iron works in small areas or new wood work with one coat of ready mixed priming paint & Two coat of approved superior quality ready mixed paint of clear synthetic varnish including supply of all materials, labour and T&P etc. required for proper completion of work. Paint to be used shaould confirm to the (ISI no. 103 1950 SI 641+642) 6 12 mm thick cement plaster of mix : 1:4 (1 cement: 4 coarse sand) DSR No.13.4.1 7 Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 8 Finishing walls with premium acrylic smooth exterior paint with Silicone additives of required shade new work (Two or more coats applied @1.43lte/10 sqm over and including priming coat of exterior primer applied @2.20 kg/10sqm) (apex Ultima, Weather coat all guard) asian, berger DSR. 13.47.1 9 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctionsof walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofingcompound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. With average thickness of 120 mm and minimum thickness at khurra as 65 mm. DAR No. 22.7.1 10 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS: 15622, of approved make, in all colours, shades, except White, lvory, Grey, Fume Red Brown, laid on 20 mm thick cement Mortar 1:4 (1 cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.30 kg/sqm including pointing the joints with white cement and matching pigment etc, complete. (DAR 16- 11.40 based) 11 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (DAR 2016 - 8.31 based) 12 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws. DAR No. 9.21.1 13 S/F Oxidised iron fitting following (ISI Marked only) 14 (i) Sliding bolt with 16mm dia nuts & bolt 250 mm long. 15 (ii) Tower Bolt with 10 mm dia rod & screw 150 mm long. 16 (iii) Door handle with screw 150 mm long 17 (B) Water Supply & Saintary fitting Work 18 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brassthreaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 19 15 mm nominal outer dia Pipes DSR No. 18.9.1 20 20 mm nominal outer dia Pipes DSR No. 18.9.2 21 Supply and fixing of PVC SWR ring fit (as per IS 13592 with latest amedments) type-A) phenolex prince suprime make soil waste andvent pipe dia 110 mm (OD) completewith all necessary fittings such as band, collor, socket, elbow Tee etc) complete for proper completion of the work as per direction of the E/I. (A/R) 22 Supply and fixing of SWR phenolex prince suprime make nahani trap 100 mm x 75 mm embeded in cement oncrete 1:2:4 (1 cement : 2 coarse sand : 4 stone grit 20 mm size) including supply of allmaterial, labour T&P etc. complete as per direction of E/I.(A/R) 23 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests DSR No. 17.1.1 24 Providing and fixing of CP BRASS jali 100 mm dia as per directions of E/I (A/R) 25 Providing & fixing 20 mm dia bore gun metal gate valve with C.I. wheel of approved quality screw end. (DSR No. 18.17.1A 26 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore DSR No. 18.50.1 27 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal boreDSR No. 18.49.1 28 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal boreDSR No. 18.53.1 29 32 mm nominal outer dia Pipes DSR No. 18.9.4 30 Supply Carting, PVC pipe (6kg/cm2) (all qualities) specials couplings, fittings to site of work lowering the same and laying ture to aligment and dradint including jointing and testing of the pipe lines i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with PVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I.160 mm nominal outer dia pepes 31 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 450x 300 mm with single 15 mm C.P. brass pillar tap DSR No. 17.7.7 32 Making G.T. chamber of size 300x300 mm with class-150 B/W in 1:6 cement and coarse sand mortar, base concrete 1:6:12 (1 cement : 6 C.sand : 12 brick ballast 40 mm size) plaster with 1:3 cement and coarse sand mortar with neat finishedincluding cost of G.T. (150x 100 mm) and C.I. cover 300x300 mm size including cost of all material, labour T&P etc required for proper completion of the work as per direction of E/I. (The weight of CI cover and frame shall not be less than 7.00 kg)(A/R)
