Tender For Repairs/Replacement Of Vertical Pumps/ Submersible Pumps/ Centrifugal Pumps/ Starter Panel/ Lt Panel Board And Other Connected Items At Various Locations Under Ge Pulgaon
Tender Value
Ref. Documents
Estimated cost
Bid Submission
22 Feb 2025
0 days left
EMD
92000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
pulgaon → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repairs/Replacement Of Vertical Pumps/ Submersible Pumps/ Centrifugal Pumps/ Starter Panel/ Lt Panel Board And Other Connected Items At Various Locations Under Ge Pulgaon
BOQ
| Sl. No. | Item Description |
| 1 | Disconnection and removing the 60 HP VT pumpset along with section, delivery pipe line,column pipe, control valves,shafts & shafts coupling etc and finding out the unserviceable parts and refixing the disconnected parts after replacing of unserviceable items with new of same size and capacity including testing and commissioning complete all as directed.Note:-Unserviceable parts will be measured and paid separately under respective items of sch \"A\"lubricating oil, Greasing, overhauling and packing kit of pump set including in the unit rate. |
| 2 | All as per item No 1 above but for40 HP VT Pump set. |
| 3 | Material & labour rewinding of 60 HP VT electric motor with super enamelled winding wire of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tape, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporate and achieving proper insulation results and reassemble the motor including replacement of terminal plate and taking out old winding complete all as directed |
| 4 | All as per item No 3 above butfor 40 HP. |
| 5 | Supply only Trans Bearing suitable for 60 HP VT pump set |
| 6 | Supply only Shaft SleevePart No 312 suitable for 60 HP VT pump set |
| 7 | Supply only Shaft SleevePart No 311.2Part No 312 suitable for 60 HP VT pump set |
| 8 | Supply only Bowl Bearing suitable for 60 HP VT pump set |
| 9 | Material and labour for spray painting of the pump set of capacity 60HP delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color asapproved by GE and marking with radium arrow for water flow direction on inlet and out let pipes. |
| 10 | Bearings suitable to the pump set(No 51220) for 60 HP VT pump set |
| 11 | Bearings suitable to the pump set(No 6220)for 60 HP VT pump set |
| 12 | Bearings suitable to the pump set(No 6311)for 60 HP VT pump set |
| 13 | Supply only Trans Bearing suitable for 40 HP VT pump set |
| 14 | Supply only Shaft SleevePart No 312 suitable for 40 HP VT pump set |
| 15 | Supply only Shaft SleevePart No 311.2Part No 312 suitable for 40 HP VT pump set |
| 16 | Supply only Bowl Bearing suitable for 40 HP VT pump set |
| 17 | Material and labour for spray painting of the pump set of capacity 40 HP delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of colour asapproved by GE and marking with radium arrow for water flow direction on inlet and out let pipes. |
| 18 | Bearings suitable to the pump set(Upper) 7316 for 40 HP VT pump set |
| 19 | Bearings suitable to the pump set(Below) 6211 for 40 HP VT pump set |
| 20 | VT pump lubricating hydraulic oil 10W KLT for 40 /60 HP VT pump set |
| 21 | Taking out defective submersible (vertical) pump set of capacity 60 HP from jack well for repair by lifting GI tubing of size 150mm to 200 mm GI/CI/MS pipe from upto 80 to 120 feet depth after disconnecting electrical and pipe line connection, complete by means of chain pully block or other T&P, transporting to workshop including repair/replacement of worn out parts, servicing and ovhauling complete with oiling/greasing, lubricating the parts and reassembling and painting of submersible pumpset with motor with one coat of synthetic enamel paint after cleaning and scrupping and shifting back to borewell, lowering commissioning and testing on full load complete all as specified and directed by Engr-in-Charge.Note :- (i) The rate quoted for this item shall includes labour charge only for maint repair and replacement of defective/UNSV spares/accessories. Spares are to measured and paid separately under subsequengt items. (ii) Cost of other minor items/ spares such as nut, bolts, washer, gaskets,paints etc which are not covered under Sch \"A\" but required for efffective functioning of the plant shall be deemed to included in this items. |
| 22 | All as per item No 21 above but for 50HP |
| 23 | All as per item No 21 above but for 40HP |
| 24 | All as per item No 21 above but for 30 HP |
| 25 | Supply only Thurst bearing complete for 60 HP Submersible vertical type pump etc. |
| 26 | Supply only Gun metal bearing bush for 60 HP Submersible vertical type pump etc. |
| 27 | Supply only Stainless steel studs and nuts for 60 HP Submersible vertical type pump etc. |
| 28 | Supply only Shaft for pump for 60 HP Submersible vertical type pump etc. |
| 29 | Supply only Shaft for motor for 60 HP Submersible vertical type pump etc. |
| 30 | Supply only Stainless steel motor coupling with key for 60 HP Submersible vertical type pump etc. |
| 31 | Supply only Three core16 sqmm submersible copper cable for connection for 60 HP Submersible vertical type pump etc. |
| 32 | Supply only Thurst bearing complete for 50 HP submersible Jack well pump etc. |
| 33 | Supply only Gun metal bearing bush for 50 HP submersible Jack well pump etc. |
| 34 | Supply only Stainless steel studs and nuts for 50 HP submersible Jack well pump etc. |
| 35 | Supply only Shaft for pump for 50 HP submersible Jack well pump etc. |
| 36 | Supply only Shaft for motor for 50 HP submersible Jack well pump etc. |
| 37 | Supply only Stainless steel motor coupling with key for 50 HP submersible Jack well pump etc. |
| 38 | Supply only Three core16 sqmm submersible copper cable for connection for 50 HP submersible Jack well pump etc. |
| 39 | Supply only Thurst bearing complete for 40 HP submersible borewell pump etc. |
| 40 | Supply only Gun metal bearing bush for 40 HP submersible borewell pump etc. |
| 41 | Supply only Stainless steel studs and nuts for 40 HP submersible borewell pump etc. |
| 42 | Supply only Shaft for pump for 40 HP submersible borewell pump etc. |
| 43 | Supply only Shaft for motor for 40 HP submersible borewell pump etc. |
| 44 | Supply only Stainless steel motor coupling with key for 40 HP submersible borewell pump etc. |
| 45 | Supply only Three core16 sqmm submersible copper cable for connection for 40 HP submersible borewell pump etc. |
| 46 | Supply only Thurst bearing complete for 30 HP submersible Jack well pump etc. |
| 47 | Supply only Gun metal bearing bush for 30 HP submersible Jack well pump etc. |
| 48 | Supply only Stainless steel studs and nuts for 30 HP submersible Jack well pump etc. |
| 49 | Supply only Shaft for pump for 30 HP submersible Jack well pump etc. |
| 50 | Supply only Shaft for motor for 30 HP submersible Jack well pump etc. |
| 51 | Supply only Stainless steel motor coupling with key for 30 HP submersible Jack well pump etc. |
| 52 | Supply only Three core16 sqmm submersible copper cable for connection for 40 HP submersible borewell pump etc. |
| 53 | Dismantling the motor of submersible (vertical type) pumpset of capacity 60 HP, removing the existing burnt out winding and re-winding with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, \"O\" rings and filling of cooling oil with oil seal and terminal lead for AC, three phase, 415Volts grade and other petty items required for making motor functional and motor reassembling and testing complete all as directed. |
| 54 | All as per item No 53 above but 50HP |
| 55 | All as per item No 53 above but 40HP |
| 56 | All as per item No 53 above but 30HP |
| 57 | M&L for fixing in replacement of CI non return valve heavy duty both end flanged incl making flanged joint, rubber gasket, nuts & bolts washers sizes 200 mm complete allas specified and directed. Make:Kirloskar/Upadhayaya/Leader |
| 58 | All as per item No 57 above here-in-above but150 mm dia. |
| 59 | All as per item No 57 above here-in-above but100 mm dia. |
| 60 | M&L for fixing in replacement of CI air release valve heavy duty single end flanged incl making flanged joint, rubber gasket, nuts & bolts washers sizes 100 mm complete allas specified and directed. Make:Kirloskar/Upadhayaya/Aarko |
| 61 | S&F in replacement of MS pipe 200 mm dia ligth grade A class both end flanged including making flanged joint, rubber gasket, nuts & bolts washers,nut and bolts complete all asspecified and as directed. |
| 62 | All as per item No 61 here-in-above but150 mm dia. |
| 63 | All as per item No 61 above but100 mm dia. |
| 64 | S & F repairsMCCB 3 pole, 250 Amp,36kA, 415V AC, 50 Hzin to the existing panel board with new one of same size and capacity complete all as directed |
| 65 | S & F repairs MCCB 3 Pole 160Amp, 36kA, 415VAC, 50 Hz in to the existing panel board with new one of same size and capacity complete all as directed |
| 66 | S & F repairs MCCB 3 Pole 100Amp, 16kA, 415VAC, 50 Hz in to the existing panel board with new one of same size and capacity complete all as directed |
| 67 | S& F repairs MCCB 3 pole, 200Amp, 415V ,36 kA,load line type with thermal settingin to the existing panel board with new one of same size and capacity complete |
| 68 | S& F in repairsMCCB 4 pole, 200Amp, 415V ,36 kA,load line type with thermal settingin to the existing panel board with new one of same size and capacity complete all as directed. |
| 69 | S& F in repairsMCCB 4 pole, 250Amp, 415V ,36 kA,load line type with thermal settingin to the existing panel board with new one of same size and capacity complete all as directed. |
| 70 | Supply & fix in replacement power contactor MNX-185, 3 Pole, 415 V, Current rating 70 A - 110 A, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor all as directed. Make : L&T/Havels/CG. |
| 71 | Supply & fix in replacement power contactor MNX-80, 3 Pole, 230 V, Current rating 80 A, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor all as directed by Engineer-in-Charge. |
| 72 | Supply & fix in replacement power contactor ML-6, 3 Pole, 415 V, Current rating 110 Amps, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor all as directed by Engineer-in-Charge. |
| 73 | Supply & fix in replacement power contactor ML-3, 3 Pole, 415 V, Current rating 110 Amps, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor all as directed by Engineer-in-Charge. |
| 74 | Supply & fix in replacement spare parts kit for 3 pole70Amps, 415 volts, with coil rating 230/415 volts, type ML-4. |
| 75 | Supply & fix in replacement spare parts kit for 3 poleMNX 140 including taking down the U/S power contractor all as directed. |
| 76 | Supply & fix in replacement spare parts kit for 3 pole 110Amps, 415 volts, with coil rating 230/415 volts, type ML-6. make L&T/Havels/CG. |
| 77 | S&F BimetalicOverload relays suitable for Power Contactor 40-70Amps, 415 volts, with coil rating 230/415 volts complete all as directedtype ML-3. |
| 78 | S&F BimetalicOverload relays suitable for Power Contactor 70-110 Amps, 415 volts, with coil rating 230/415 volts complete of all as directed |
| 79 | S&F BimetalicOverload relays suitable for Power Contactor 110Amps, 415 volts, with coil rating 230/440 volts complete of all as directed |
| 80 | S&F BimetalicOverload relays suitable for Power Contactor 20 to 33Amps, 220 volts, with coil rating 230/440 volts complete of all as directed |
| 81 | Supply & fix in replacement in repairs spare parts kit for 3 pole80Amps, 415 volts, with coil rating 230/415 volts, type ML-4. all as directed |
| 82 | S&F in repairs BimetalicOverload relays suitable for Power Contactor 40Amps, 415 volts, with coil rating 230/415 voltstype ML-3.complete all as directed |
| 83 | S&F in repairs BimetalicOverload relays suitable for Power Contactor 70Amps, 415 volts, with coil rating 230/415 volts complete of complete all as directed |
| 84 | S&F in repairs SDz5 star delta timer 50 Hz complete all as directedand specifed. |
| 85 | M&L in repair of rusted & crack CI/DI water branch connection 150 to 300mm dia by using mechanical joint with connecting all accessoriescomplete all as specified and directed byEngineer-in-Charge. Note :(i)cost ofgasket and nut bolts ,washers\"jointing of materials as required are inclusive in above job.ii)Required T&P for job is provided by the Contractor is deemed to be included in the item rate.(iii)Excavation for pipe is included in job Work. |
| 86 | Disconnection and removing the broken S/S spindle with checknut and S&F brass spindle of samesize and length along with checknutsuitable for sluice valve 300 mm borePN 1.6/PN1of exisisting makesincluding threading machining and Lathe work complete along with fixing material such asgland packing nut and bolts complete. |
| 87 | All as per item No 86 abovebut200 mm bore. |
| 88 | All as per item No 86 abovebut150 mm bore. |
| 89 | M&L for CI special/fittings suitable for CI flanged/socket ends pipe upto 150 to 300 mm bore dia such as bends, (any radius and angle), tapers any type (straight, bend, increasing, decreasing or double socket etc) tee piece, single branch \"Y\" junction, double branch, cross (all flanged), collars, caps & plug, tail pieces, reducers, mechanical joint, etc. including nuts, bolts and washersand necessary boring to match the existing pipe complete all as specified and as directed, |
| 90 | Supply, installation, commissioning and testing of star delta stater fully automatic suitable for 30 HP/40 HP submersible pump, 415 volts 3 phase, 50 Hz with ML-4 contactors including taking out of existing u/s starter as directed. Make- L&T/Siemens/Schneider (CG). |
| 91 | Material and labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earths strip 32 X 6 mm size by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-Iconnected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete. |
| 92 | All as per item No 91 here-in-above butsize 25mm x 4mm conductor. |
| 93 | S &F of single phase preventor(Phase failure relay) 415Volt,50 Hz,Type-VSP 3 complete all as specified and directed. |
| 94 | M&L for disconnecting removing the water meter 300 mm (NB) make Capstan B class flange end and transporting to authorized service center for repair, clibration, testing and refixing, comissioning, testing andfixing proper seal including nutbolts, rubber sheet etc of suitable size all as directed and specified. |
| 95 | Disconnection and removing the top cone unit (split casing cover) of the unserviceable pump 120HP along with suction, delivery pipe line, control valves etc and refixing the disconnected parts after replacingunserviceable parts with the new parts of same size,capacity and make and making the pump in serviceable condition including testing and commissioning complete all as directed for the following capacities:- Note:-The replacement of unserviceable parts with new parts will be measured and paid separately under respective items of sch \"A\" as supply only and labour element for fixing including greasing, overhauling and packing of pump set will be included in the unit rate quoted for this item. |
| 96 | Disconnection and removingthe unserviceable Electric motor 120 HP and transporting the same to work shop for rewinding and fixing the same in its original position after repairs, including testing and commissioning complete all as directed |
| 97 | Material & labour rewinding of 120 HP electric motor with fine enameled bared copper conductor of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tap, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporates and achieving proper insulation results and reassemble the motorincluding taking out old rewinding complete all as directed. |
| 98 | Supply only Rubber tyre Pulley along with nut, bolts and key unit complete set suitable for 120 HP pump set |
| 99 | Supply only MS Impeller of suitable capacity suitable for 120 HP pump set |
| 100 | Supply only Bearings suitable to the pump set (3309) suitable for 120 HP pump set |
| 101 | Supply only Bearings suitable to the pump set (6309) suitable for 120 HP pump set |
| 102 | Supply only Gasket suitable for 120 HP pump set |
| 103 | Material and labour for spray painting of the pump set of capacity 120 HP with suction/delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color asapproved by GE and marking with radium arrow for water flow direction on inlet and out let pipes. |
| 104 | Shaft stainless steel suitable for pump set including machining, threading, metaling & lathework complete. |
| 105 | Bearings suitable for 120 HP motor (for drive end & dead end) (317C-3/6317C-3) |
| 106 | Bearings suitable for 120 HP motor (6318) |
| 107 | Disconnection and removing of the 7.5 HP monoblock pump along with suction, delivery pipe line, control valves etc and finding out the unserviceable parts and refixing the disconnected parts after replacing of unserviceable items with new of same size and capacity including testing and commissioning complete all as directed .Note:-(i) Unserviceable parts will be measured and paid separately under respective items of sch \"A\" (ii)Greasing, overhauling and packing of pump set will be include in the unit rate. |
| 108 | Material & labour rewinding of 7.5 HP electric motor with fine enameled bared copper conductor of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tap, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporates and achieving proper insulation results and reassemble the motorincluding taking out old rewinding complete all as directed for the following capacity. |
| 109 | Supply only Coupling along with nut, bolts and key unit complete suitable for 7.5 HP monoblock pump pump set |
| 110 | Supply only MS Impeller of suitable capacity suitable for 7.5 HP monoblock pump pump set |
| 111 | Supply only Impeller lock nut suitable for 7.5 HP monoblock pump pump set |
| 112 | Supply onlyImpeller sleeves suitable for 7.5 HP monoblock pump pump set |
| 113 | Supply only Bearings suitable to the pump set suitable for 7.5 HP monoblock pump pump set |
| 114 | Supply only Gasket suitable for 7.5 HP monoblock pump pump set |
| 115 | Material and labour for painting of the pump set of capacity 7.5 HP with suction/delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color asapproved by GE and marking with radium arrow for water flow direction on inlet and out let pipes. |
| 116 | Shaft stainless steel suitable for pump set including threading, machinery & lathe work complete. |
| 117 | Bearings suitable for 7.5 HP motor (for drive end & dead end) |
| 118 | Taking out defective submersible (vertical) pump set of capacity 7.5 HP/10HP from bore well for repair by lifting GI tubing of size 50mm to 150 mm GI/CI/MS pipe from upto 220 to 250 feet depth after disconnecting electrical and pipe line connection, complete by means of chain pully block or other T&P, transporting to workshop including repair/replacement of worn out parts, servicing and ovhauling complete with oiling/greasing, lubricating the parts and reassembling and painting of submersible pumpset with motor with one coat of synthetic enamel paint after cleaning and scrupping and shifting back to borewell, lowering commissioning and testing on full load complete all as specified and directed .Note :- (i) The rate quoted for this item shall includes labour charge only for maint repair and replacement of defective/UNSV spares/accessories. Spares are to measured and paid separately under subsequengt items. (ii) Cost of other minor items/ spares such as nut, bolts, washer, gaskets,paints etc which are not covered under Sch \"A\" but required for efffective functioning of the plant shall be deemed to included in this items. |
| 119 | All as per item No 118 above but3 HP/5 HP. |
| 120 | Supply only Thurst bearing complete for 7.5 HP/10HP submersible borewell pump etc. |
| 121 | Supply only Gun metal bearing bush for 7.5 HP/10HP submersible borewell pump etc. |
| 122 | Supply only Shaft for pump for 7.5 HP/10HP submersible borewell pump etc. |
| 123 | Supply only Shaft for motor for 7.5 HP/10HP submersible borewell pump etc. |
| 124 | Supply only Stainless steel motor coupling with key for 7.5 HP/10HP submersible borewell pump etc. |
| 125 | Supply only SWR rope 6mmfor 7.5 HP/10HP submersible borewell pump etc. |
| 126 | Supply only Thurst bearing complete for 3HP/5HP submersible borewell pump etc. |
| 127 | Supply only Gun metal bearing bush for 3HP/5HP submersible borewell pump etc. |
| 128 | Supply only Stainless steel studs and nuts for 3HP/5HP submersible borewell pump etc. |
| 129 | Supply only Shaft for pump for 3HP/5HP submersible borewell pump etc. |
| 130 | Supply only Shaft for motor for 3HP/5HP submersible borewell pump etc. |
| 131 | Supply only Stainless steel motor coupling with key for 3HP/5HP submersible borewell pump etc. |
| 132 | Supply only SWR rope 6mmfor 3HP/5HP submersible borewell pump etc. |
| 133 | submersible cabe 3 core copper conductor cable 6 sq mm |
| 134 | Dismantling the motor of submersible (vertical type) pumpset of capacity 7.5HP/10HP, removing the existing burnt out winding and re-winding with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, \"O\" rings and filling of cooling oil with oil seal and terminal lead for AC, three phase, 415Volts grade and other petty items required for making motor functional and motor reassembling and testing complete all as directed |
| 135 | All as per item No 134above but3 HP/5 HP. |
| 136 | Spray Painting of the MS fabricatedstructureof Sedimentation tank (two parts) including filter bed, outlet sluice valvecomplete by one coat of synthetic enameal paint as approved. Note :- necessary safety precautions should be taken in the cost of using safety belts is deemed to be included in the cost |
| 137 | Supply and fix in replacement CI Foot valve unit double flap , suitable for 200mmbore incl required nuts and bolts etc and cone set the same to the suction pipe of the pump set availble in to the sum appxhight of 14 feet below the ground level of the sump all as specified and directed. Make:Kirloskar/Upadhya/Leader . |
| 138 | All as per item No 137 abovebut250 mm bore. |
| 139 | All as per item No 137 abovebut150 mm bore. |
| 140 | Excavation in trenches by mechnical means (hydraulic excavator) not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out all kind ofsoil complete all as specified and as directed. |
| 141 | Returning, filling in, including spreading, leveling watering and well ramming in layers of soil not exceeding 25cm. |
| 142 | Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point of rock. |
| 143 | Taking up CI/DI water mains 300mm dia class B (including all fittings), with spigot and socket ends and lead joints including burning out joints / tyton joints complete all as specified and as directed. |
| 144 | All as per item No 143 here-in-above but200mm |
| 145 | All as per item No 143 abovebut 150mm |
| 146 | Relayingonly old CI/DI pipe in good condition/pipe taken out from trenches for repairsin any length including fittings etc. of size 300 mm bore |
| 147 | All as per item No 146here-in-above but200mm |
| 148 | All as per item No 146 abovebut 150mm |
| 149 | Supply and fix cast iron pipes with spigot and socket ends centrifugally costed class B in any length suitable for rubber tytan joint andLaid in trenches of size 300mm bore |
| 150 | All as per item No 149here-in-above but200mm bore. |
| 151 | All as per item No 149above but 150mm bore. |
| 152 | M&L for burning out lead joint in position , including removing lead to store / stacked at site to issue under credit of 300mm bore CI Pipe line |
| 153 | M&L for Run lead joint of 300 mm bore of spigot socket pipes and fitting, including caulking properly and making joint leak proof all as directed and as specified. |
| 154 | Servicing ofIron removing plant with pressure filter, catalytic media, air compressor, suitable for back washing of capacity 1000 GL/H complete in all respect. Make ELGI.: U/S spare parts shall be measured and paid separately as supply only here in after). |
| 155 | Air filter |
| 156 | Air oil separator |
| 157 | Oil filter |
| 158 | Air Lub oil |
| 159 | S&F in repair Pressure gauge range 0-21 KG per cm square for centrifugal pump/VT Pump setproper fix suitablepoint with suitable fixing arrangement (i.e nut bolt, boresuitable,fixing pipe for pressure gauge on mounting all as directed. |
| 160 | Supply & fix in replacement champion/turner style graphite gland packing of sizes as 8/10/12/16mm thick. For motor/sluice valve. |
| 161 | Dismantaling of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level). |
| 162 | M&L for Cement concrete 1:2:4 B-2 using 40mm graded stone aggregatein foundations, filling and mass concrete. |
| 163 | Repair to CI valve for back wash in filter plant ( Plate type) 200MM/300mm, including threading, machinery and lathe work complete along with fixing material such asRubber sheetpacking, nut and bolts,etc complete. |
| 164 | All as per item No 163 here-in-above but150mm bore. |
| 165 | M&L in repair chequered plate including cut to required size and making provision of handle made out of 6 mm plane rod,including painting with two coats of synthetic enamel paint over one coat of red oxide all as directed . |
| 166 | Taking down existing UNSV sluice valve and supply & fix new Sluice valve of80mm bore rising spindle type (Gear type) PN-1.6 heavy duty ISI marked as per (IS-14846) with flanged ends with 02 Nos of rubber gaskets, nut bolts and washers along with SS spindle and oprating wheel of following sizes :- |
| 167 | All as per item No 166 above but150mm bore. |
| 168 | All as per item No 166 above but 200mm bore. |
| 169 | All as per item No 166 above but 300mm bore. |
| 170 | All as per item No 166 above but 250mm bore. |
| 171 | Supply and fix in repair and replacement of leather flapper for the 200mm CI Foot valve unit, including required nuts and bolts etc and cone set and fixing the same to the suction pipe of the pump set availble in to the sump appx at a height of 15 feet below the ground level of the sump all as specified and directed. |
| 172 | Spray Painting ofMS sheet cover for Valve chamber cover/US sump cover/Air release valve/ filter water reservoir square type of water supply all installation with two coat of enamel paint colour coat over a coat of redoxide areapproved make by GE. |
| 173 | S&F in repair Mild steel work in Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work con- forming to Fe.290.Gde-E-165 |
| 174 | S&F in replacement of microprocessor based electronic water level indicataor based on 3 wire interfacing system in between OH Tank/UG Tank sensor to main water level indicator units showing indication in percent by seven segment LED display in 10 step (10%, 20%, 30% ............100%) having 10 combined sensor for total depth of tank of make : Serval/Optic/IEC/Benzer with all fixing/grouting arrangement suitable for RCC OH Tank/UG Tank of 0.5 to 1.5 lakh gallons capacity including dismantling and taking down old unserviceable water level indicator, any type and depositing to MES store yard complete all as specified and directed. Processor based electronic water level indicator shall also comprising of the following items:- Multi level (10 to 100%) indication in three digit with seven segment with bright LED display. Sensor with suitablefixing arrangement in over head tank haaving electronic circuit to transmit the sensing signal of each level to display unit shall be fitted in pump house. Controller/power unit with sensing volts (6-12 volts) enclosed with sheet metal enslosure/wooden board and hylum sheet including proper mounting arrangements. PDC insulated multi- straudedcopper conductor communication cable 2.5Sqmm, 3 core from LT Panel to controller/power unit drawn through 20mm dia non metalic PVC conduit medium grade with all accessories including all fixing arrangements. Hooter with ON/OFF switch to alarm the pump operator when tank is full.complete all as directed by EIC. |
| 175 | Supplyand laying or fixing or passing through pipe in replacement ,testing and commissioning 1100voltsgrade heavy dutycablewith PVC insulated multi strand copper conductor cable size 95 Sqmm, single core unsheathed flexible including of suitable size lugs and connection plate of sutiable typeall as specied and as directed |
| 176 | Supplyand laying or fixing or passing through pipe in replacement ,testing and commissioning 1100voltsgrade heavy dutycablewith PVC insulated multi strand copper conductor cable size 70Sqmm, single core unsheathed flexible including of suitable size lugs and connection plate of sutiable typeall as specied and as directed |
| 177 | All as per item No 176 here-in-above but of size 35 sqmm. |
| 178 | All as per item No 176 above but of size 25 sqmm. |
| 179 | Supply, installation, commissioning and testing of smart star delta stater fully automatic ,LCD based,Digital time setting ,Smart/Auto switch ,protects motor against reverse running & unbalanced voltage conditionsfor upto120 HPcentrifugal pump, 440 volts 3 phase, 50 Hz including taking out of existing u/s starter as directed. Make- L&T/Siemens/Schneider (CG). |
| 180 | Supply, installation, commissioning and testing of DOL stater fully automatic suitable for upto7.5HPmonoblock pump, 415 volts 3 phase, 50 Hz,10-40A including taking out of existing u/s starter as directed. Make- L&T/Siemens/Schneider (CG). |
| 181 | M&L cleaning the Decrin dozer assembly complete by opening of nut, bolts gate valve and connected GI fitting and refixing/assembling complete all as specified and as directed. |
| 182 | Comprehensive maintenance and repair of calcium hypochlorite based electronic automatic dosing equipment 100 Ltr capacity of any type and make complete with dozing tube and solution drum and other accessories required. Note :- (i) Spare items/parts required for chloronomes plant shall be measured and paid separately under relevent items. (ii) Cost of items /parts which are not covered in Sch \"A\" but are necessary for the satisfactory functioning for the plant shall be included in the rate quoted for this item. (iii) Dosing pump to be cleaning twice in a month (15 days) and serviceability report to be submitted to Engr-in-charge for office record.(iv) Labour charges for removal ofunserviceable parts and fixing of spare items/parts (supplied under the item No-84) shall be deemed to be included in the rate quoted for this item. |
| 183 | Supply only for replacement of Pump head (Ferrules 1/4\" & Duckbill included) of decrine dozer |
| 184 | Supply only for replacement of Roller assembly of decrine dozer |
| 185 | Supply only for replacement of Pump tubeof decrine dozer |
| 186 | Supply only for replacement of Injection check valve 3/8\"of decrine dozer |
| 187 | Supply only for replacement of Weighted suction line strainer 3/8\" of decrine dozer |
| 188 | Supply only for replacement of Rotor assembly with bearing brackets & tolerance ring of decrine dozer |
| 189 | Supply only for replacement of Coil 250V 50Hz of decrine dozer |
| 190 | Supply only for replacement of 3/8\" White suction/Discharge tubing of decrine dozer |
| 191 | M&L for dismantling soft starter for 120HP Pump set and taking to workshop for fireware updation and replacement of motor control PCB EMZ4E soft starter and reinstalling, commissioning and testing complete all as specified and directed. |
| 192 | Servicing of D-Watering Pump capacity 7.5 HPand taking out the defective/unserviceable parts and re-assembling the same after repair/replaced and testing complete all as specified and directed.(Note : U/S spare parts shall be measured and paid separately as supply only here in after). |
| 193 | Diesel filter |
| 194 | Oil filter |
| 195 | Oil pressure gauge |
| 196 | HDPE 80 mm dia of presure rating 2.5 Kg/Sqcm alogwith coupling socketsetclamps & clips complete all as specified and directed. |
| 197 | Testing ofTreated water (Drinking water)sample as per IS - 10500 including collecting of sample from the pump house and handed over it to the authoriesed lab for the testing purpose all as specified and directed. |
| 198 | Testing ofRaw watersample as per IS - 10500 including collecting of sample from the pump house and handed over it to the authoriesed lab for the testing purpose all as specified and directed. |
| 199 | Disconnection and removing of the 50 HP monoblock pump of make Kirloskar with 70 mtr head along with suction, delivery pipe line, control valves etc and finding out the unserviceable parts and refixing the disconnected parts after replacing of unserviceable items with new of same size and capacity including testing and commissioning complete all as directed .Note:-(i) Unserviceable parts will be measured and paid separately under respective items of sch \"A\" (ii)Greasing, overhauling, lubricating and packing of pump set will be include in the unit rate. |
| 200 | Material & labour rewinding of 3 phase 50 HPinduction motor of make Kirloskar model DB 65/26xe RPM 2900 with fine enameled bared copper conductor of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tap, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporates and achieving proper insulation results and reassemble the motorincluding taking out old rewinding complete all as directed for the following capacity. |
| 201 | Supply only Coupling along with nut, bolts and key unit complete suitable for 50 HP monoblock pump pump set |
| 202 | Supply only Bronze Impeller of suitable capacity suitable for 50 HP monoblock pump pump set |
| 203 | Supply only Impeller lock nut suitable for 50 HP monoblock pump pump set |
| 204 | Supply only Mechnical seal suitable for 50 HP monoblock pump pump set |
| 205 | Supply only Bearings suitable to the pump set suitable for 50 HP monoblock pump pump set |
| 206 | Supply only Gasket suitable for 50 HP monoblock pump pump set |
| 207 | Supply only Ball bearings of suitable size suitable for 50 HP monoblock pump pump set |
| 208 | Material and labour for painting of the pump set of capacity 50 HP with suction/delivery pipe line approx 20 mtr including valves with two coats of synthetic enamel paint of color asapproved by GE and marking with radium arrow for water flow direction on inlet and out let pipes. |
| 209 | Shaft stainless steel suitable for pump set including threading, machinery & lathe work complete. |
| 210 | Bearings suitable for 7.5 HP motor (for drive end & dead end) |
| 211 | Supply, lay, connecting, jonting and testing ductile iron pressure pipe ISI marked, IS-8329-2000 odf dia 300mm sutable for push on joint with rubber gasket for water supply class K9 |
| 212 | M&L in repair for cutting existing CI/DI pipe and inserting Tee of (300x300x300)mm dia connectingfor branch connention includingmaking connection leak proof complete. Note: i) Necessary excavation will be deemed to be included in quoted rates (ii) Necessary Tee, collars, adaptors will be measured and paid seperately under relevant schedule items. M&L Necessary anchorage of Angle iron (50x50x6)mm along with PCC thrust block and PCC as required to be included in quoted rates |
| 213 | S&F in replacement HBC ETN fuse 200 FM IEC 690V AC |
| 214 | S&F in replacement HBC ETN fuse 400 MMT FM IEC 690V AC |
AI Tender Summary
Tender Timeline
Feb 01, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 22, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 04, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender