|
| 1 | M&L of fabricating and fixing wall mounted display board suitable for flow charts, schematic diagrams, layout of machinery, technical instructions etc, at E&M installationsstenciled letters or drawingsprinting on acrylic sheet (4 mm thick) single piece sheetswith necessary hooks and hanging arrangement all as directed.Note: The soft copies of printing matter/drawings shall be provided by the Dept and colour of sheet & letters will as directed by Engr in Charge. |
| 2 | Taking down interloacking paver block any type any size includinh taking out of PCC form work, sand filling , sub base PCC including hard core as per requirement at site complete |
| 3 | M&L sand filling under floors or in foundations including watering and consoildation complete all as directed |
| 4 | M&L for machine pressed precast concrete interlocking paver block any shape conforming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey concrete and pigcement complete all as directed |
| 5 | M&L for Hard core broken to gauge n exc 63 mm using broken stone or boulders complete all as directed |
| 6 | M&L for 100 mm thick PCC type C-2 1:3:6 (40 mm aggregate) as in sub base, floors and paving etc paving complete all as directed. |
| 7 | M&L for providing plain cement concrete type B-1 (1:2:4) using 20 mm graded stone aggregate in roof kerb or mud slops, rounded or chamfered on edges complete all as specified and directed. |
| 8 | Forming work to edges of concrete flats, treads, breaks in floods, window cills, concrete railing, openings in concrete walls, floors and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work exc 10 cm but n exc 20 cm wide complete |
| 9 | Surface excavation n exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out inhard/dense soil |
| 10 | Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point of any soil |
| 11 | M&L for PCC 1:3:6 Type C2for foundation of platform, mass concrete with 40 mm gradede coarse agreegete complete all as specified and as directed. |
| 12 | M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete. |
| 13 | Materialand labour for rendering 10 mm thick cement plaster in cement mortar (1:4) on old face of brick work or concrete surface on walls complete all as specified and directed. |
| 14 | Dismantiling the DG setcarefully by authorised service centre including cyclinder head ,piston assy, radiator assy, inlet and exhaust manifold, turbo charger,fuel pipes, silencer and others accessories complete of capacity 320 KVA. |
| 15 | Shifting of cylinder head to workshop at Tezpur for necessary inachine work including grinding of cylinder head, fitting of valve seat, valve gaide, valve collect, valve spring etc of DG Set 320 KVA all as required.Note: Spares required for repair of cylinder head will be measured and paid separately. |
| 16 | Overhauling and calibration of Fuel Injection Pump including replacement of Nozzle, Spring, delivery valve, adjustment screws, barrel pump plunger of DG Set 320 KVA etc all as required. |
| 17 | Repair calibration of Injector assembly including replacement oif Nozzles, barrel plunzer, Injector cup etc of DG Det 320 KVA all as required. |
| 18 | Top over hauling of DG Set 320 KVA as per manufacturer instruction including replacement of defective parts as required to complete the job for smooth functioning of DG Set as specified and directed by Engr-in-Charge.Note: Spares required for Top over hauling will be measured and paid separately. |
| 19 | Supply only New spares required for Top Overhauling of DG Set 320 KVA mentioned against Srl item 18 here in before:- |
| 20 | Cylinder Linear cat part No 3006089 |
| 21 | Gasket set Cylinder Head cat part No 2884896 Make : Cummins |
| 22 | Exhaust Valve cat part No 3035110 Make : Cummins |
| 23 | Inter Valve cat part No 2072241 Make : Cummins |
| 24 | Valvo Guide cat part No 3201311 Make : Cummins |
| 25 | Valvo insertcat part No 3872343 Make : Cummins |
| 26 | Valvo spring cat part No 3629006 Make : Cummins |
| 27 | Gasket set complete cat part No 4072231 Make : Cummins |
| 28 | Set of O Ring cat part No 3420791 Make : Cummins |
| 29 | Set of Oil seal cat part No 3003353 Make : Cummins |
| 30 | Push Rod (Valve) cat part No 3046431 Make : Cummins |
| 31 | Push Rod Injector cat part No 3017961 Make : Cummins |
| 32 | CR Bushing bearing cat part No 3043909 |
| 33 | Connecting Rod bearing cat part No 205840 (set of 12 Nos) Make : Cummins |
| 34 | Valve seal insert cat part No 205094 Make : Cummins |
| 35 | Throttle control lever cat part No 3006440 Make : Cummins |
| 36 | Safety control LLD cat part No 3231518 Make : Cummins |
| 37 | Safety control HWT cat part No 3231517 Make : Cummins |
| 38 | Valve Solenoid cat part No 3239599 Make : Cummins |
| 39 | Varner control cat part No 3229310 Make : Cummins |
| 40 | Belt \"V\" cat Part No 178587Make : Cummins |
| 41 | Gear Pump cat Part No 3034221Make : Cummins |
| 42 | Cam flower roller valve injector cat Part No 3016626Make : Cummins |
| 43 | Cam flower roller pin cat Part No 4009248Make : Cummins |
| 44 | Spilt Pin cat Part No 205438Make : Cummins |
| 45 | Cam Flower shaft cat Part No 3066217Make : Cummins |
| 46 | Cam flower lever cat Part No 3081250Make : Cummins |
| 47 | Water pump assembly cat Part No 4950317Make : Cummins |
| 48 | Piston Ring set cat Part No 2865146Make : Cummins |
| 49 | Pillow block assembly cat Part No 218008Make : Cummins |
| 50 | Shaft idlor cat Part No 34021717Make : Cummins |
| 51 | Rocker lever cat Part No BM87993Make : Cummins |
| 52 | Rocker Bush cat Part No 3092523Make : Cummins |
| 53 | Shaft Rocker cat Part No 3176773Make : Cummins |
| 54 | Piston Cooling Nozzle cat Part No 3007517Make : Cummins |
| 55 | Turbochargercat Part No 3524034Make : Cummins |
| 56 | Thermostat cat Part No 01307355 |
| 57 | Cross Head seal rectangular ring cat Part No 3056100Make : Cummins |
| 58 | Temperatrure L/O Gauge cat Part No 50413Make : Cummins |
| 59 | RPM Meter cat Part No 3231403Make : Cummins |
| 60 | Valve Sole cat part No 3239599Make : Cummins |
| 61 | Shut Off valve cat part No 3239601Make : Cummins |
| 62 | Hose AK cat Part No 6045STMake : Cummins |
| 63 | Hose AK cat Part No 5042SS Make : Cummins |
| 64 | V Belt cat Part No 3001601 |
| 65 | Cam shaft cat Part No 3066889 |
| 66 | Water temperature gauge cat Part No 504148 |
| 67 | Dismantiling the DG setcarefully by authorised service centre including cyclinder head ,piston assy, radiator assy, inlet and exhaust manifold, turbo charger,fuel pipes, silencer and others accessories complete of capacity 100 KVA. |
| 68 | Shifting of cylinder head to workshop at Tezpur for necessary inachine work including grinding of cylinder head, fitting of valve seat, valve gaide, valve collect, valve spring etcof DG Set 100 KVA all as required.Note: Spares required for repair of cylinder head will be measured and paid separately. |
| 69 | Overhauling and calibration of Fuel Injection Pump including replacement of Nozzle, Spring, delivery valve, adjustment screws, barrel pump plunger etc of DG Set 100 KVA all as required. |
| 70 | Repair calibration of Injector assembly including replacement oif Nozzles, barrel plunzer, Injector cup etc of DG Set 100 KVA all as required. |
| 71 | Top over hauling of DG Set 100 KVA as per manufacturer instruction including replacement of defective parts as required to complete the job for smooth functioning of DG Set as specified and directed by Engr-in-Charge.Note: Spares required for Top over hauling will be measured and paid separately. |
| 72 | Supply only New spares required for Top Overhauling of DG Set 100 KVA mentioned against Srl item 24 here in before:- |
| 73 | Cylinder Linear |
| 74 | Gaseket Set Cylinder head |
| 75 | Exhaust Valve |
| 76 | Inter Valve |
| 77 | Valvo Guide |
| 78 | Valvo insert |
| 79 | Valvo spring |
| 80 | Gasket set complete |
| 81 | Set of O Ring |
| 82 | Set of Oil seal |
| 83 | Push Rod (Valve) |
| 84 | Push Rod Injector |
| 85 | CR Bushing bearing |
| 86 | Connecting Rod bearing |
| 87 | Valve seal insert |
| 88 | Belt \"V\" |
| 89 | Gear Pump |
| 90 | Water pump assembly |
| 91 | Piston Ring set |
| 92 | Rocker lever |
| 93 | Rocker Bush |
| 94 | Shaft Rocker |
| 95 | Turbo charger |
| 96 | Thermostate |
| 97 | Cross head seal |
| 98 | Valve Solenoid |
| 99 | Shut Off valve |
| 100 | Hose AK Part No 6045ST |
| 101 | Hose AK Part No 5042SS |
| 102 | V Belt Part No 3001601 |
| 103 | Cam shaft |
| 104 | Electronic panel Board 6 BT with all equipments |
| 105 | Dismantiling the DG setcarefully by authorised service centre including cyclinder head ,piston assy, radiator inlet and exhaust manifold, turbo charger,fuel pipes, silencer and others accessories complete of capacity 35 KVA. |
| 106 | Overhauling and calibration of FuelPump diesel engine of 35 KVA by authorised service centre including replacement of injector including wornout parts ie delivery valve, nozzle spring adjustmentbarrel pump plunger etc of DG Set 35 KVA all as required. |
| 107 | Repair calibration of Injector assembly including replacement oif Nozzles, spring, barrel plunzer, Injector cup etc of DG Set 35 KVA all as required. |
| 108 | Repair to self starter assembly by authorised service centre replacement of wornout armature carbon bushes and bushes complete of DG Set 35 KVA all as required. |
| 109 | Repair of cylinder head with necessary machine work including grinding ,fitting of valve etc of DG Set 35KVA all as required.Note: Spares required for repair of cylinder head will be measured and paid separately. |
| 110 | Top over hauling of DG Set 35 KVA as per manufacturer instruction including replacement of defective parts as required to complete the job for smooth functioning of DG Set as specified and directed by Engr-in-Charge.Note: Spares required for Top over hauling will be measured and paid separately. |
| 111 | Supply only New spares required for Top Overhauling of DG Set 35 KVA mentioned against Srl item 31 here in before:- |
| 112 | Cylinder linear |
| 113 | Piston ring |
| 114 | Gaseket Set Cylinder head |
| 115 | Exhaust Valve |
| 116 | Inlet Valve |
| 117 | Valvo Guide |
| 118 | Valvo spring |
| 119 | Gasket set complete |
| 120 | Set of O Ring |
| 121 | Set of Oil seal |
| 122 | Push Rod |
| 123 | CR Bushing bearing |
| 124 | Connecting Rod bearing |
| 125 | Belt \"V\" |
| 126 | Gear Pump |
| 127 | Water pump assembly |
| 128 | Piston |
| 129 | Alternator assembly 12v 25 A |
| 130 | AVR suitable for 35 KVA alternator |
| 131 | AVM pad |
| 132 | Radiator assembly 35 KVA |
| 133 | Dismantiling the Diesel driven pump setcarefully by authorised service centre including cyclinder head ,piston assy, radiator inlet and exhaust manifold, turbo charger,fuel pipes, silencer and others accessories complete of capacity 126 BHP. |
| 134 | Overhauling and calibration of FuelPump Diesel driven pump setby authorised service centre including replacement of injector including wornout parts ie delivery valve, nozzle spring adjustmentbarrel pump plunger etc of Diesel driven pump set126 BHP all as required. |
| 135 | Repair calibration of Injector assembly including replacement oif Nozzles, spring, barrel plunzer, Injector cup etc of Diesel driven pump setall as required. |
| 136 | Repair to self starter assembly by authorised service centre replacement of wornout armature carbon bushes and bushes complete of Diesel driven pump setall as required. |
| 137 | Repair of cylinder head with necessary machine work including grinding ,fitting of valve etc of Diesel driven pump setall as required.Note: Spares required for repair of cylinder head will be measured and paid separately. |
| 138 | Top over hauling of Diesel driven pump set126 BHP as per manufacturer instruction including replacement of defective parts as required to complete the job for smooth functioning of DG Set as specified and directed by Engr-in-Charge.Note: Spares required for Top over hauling will be measured and paid separately. |
| 139 | Supply only New spares required for Top Overhauling o fDiesel driven pump setmentioned against Srl item 38 here in before:- |
| 140 | Cylinder linear |
| 141 | Piston ring |
| 142 | Gaseket Set Cylinder head |
| 143 | Exhaust Valve |
| 144 | Inlet Valve |
| 145 | Valvo Guide |
| 146 | Valvo spring |
| 147 | Gasket set complete |
| 148 | Set of O Ring |
| 149 | Set of Oil seal |
| 150 | Push Rod |
| 151 | CR Bushing bearing |
| 152 | Connecting Rod bearing |
| 153 | Belt \"V\" |
| 154 | Gear Pump |
| 155 | Water pump assembly |
| 156 | Piston |
| 157 | AVM pad |
| 158 | Turbocharger assembly |
| 159 | M & L for DOL starter in replacement of suitable for electric motors in sheet enclosure Type MN, AC 3 Phase, 415 Volt, 50 Hz with thermal over load relay range 11-18 Amps 10 HP incl provision of mounting arrangement with MS flat strips 40 mm x 5 mm thick of suitable length and shape duly drilled and embedded to wallincl making good disturbed surfaces complete all as specified and directed.Make- L&T /Havells/CG |
| 160 | M & L for FASD starter in replacement of suitable for electric motors in sheet metal enclosure Type MN, AC 3 Phase, 415 Volt, 50 Hz with thermal over load relay range 40-80 Amps of capacity 50/60 HP incl provision of mounting arrangement with MS flat strips 40 mm x 5 mm thick of suitable length and shape duly drilled and embedded to wallincl making good disturbed surfaces complete all as specified and directed.Make- L&T /Havells/CG |
