|
| 1 | Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed. |
| 2 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed. |
| 3 | Removing Excavated soils not exc 50 Mand depositing where directed at a level not exc1.5 M above the starting pointcomplete all as specified and directed. |
| 4 | M&L for plain cement concrete, Type B2 1:2:4 (using 20 mm gradedstone aggregate)in foundations, filling and mass concretecomplete all as specified and directed. |
| 5 | M&L PCC 1:2:4 type B-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed. |
| 6 | Supply only integral water proofing compound complete all as specified. |
| 7 | M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 8 | M&L for Burnt Brick work with sub-class `B\" bricks, straight or curved on plan to any radius in half brick thick wallbuilt in cement mortar 1:6 complete all as specified and directed. |
| 9 | S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed. |
| 10 | S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as per IS-1003 (Part-2), kiln seasonable and chemically pressure treated and fitted to chowkhats complete all as specified and directed.(Note – Glass / wire cloth will be measured and paid separately). |
| 11 | S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side with decorative face veneer with liping/frame to match complete all as specified and directed. |
| 12 | Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 13 | Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 14 | S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. |
| 15 | Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed. |
| 16 | S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed. |
| 17 | S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 18 | S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed. |
| 19 | S & F Rolled Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, rollers, cleats base plates etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe – 290 – W(Gde E - 165) quality \"A\"complete all as specified and directed. |
| 20 | S&F framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 (Gde-E-165) complete all as specified and directed. |
| 21 | M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 22 | S & F Joist, channel, angle, flat iron or tee sections, fixed independently, with connecting plates, etc. confirming to Fe 410 -W (Gde-250 quality A) complete all as specified and directed. |
| 23 | S & F of structural steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed. |
| 24 | S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. |
| 25 | S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed. |
| 26 | S&F steel ventilator with top hung shutter and including hinges steel peg stay complete all as specified and directed. |
| 27 | S&F 150 mm floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 28 | S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed. |
| 29 | S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed. |
| 30 | M&L for 75 mm thick cement concrete, type D-2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring finished rough to receive finishes complete all as specified and directed. |
| 31 | M&L rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed. |
| 32 | M&L cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 33 | M&L Machine cut kota stone 20-25 mm thick as in single piece as flooring , treads over &including 25 mm thick rendering in CM 1:6laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including rubbing/grinding andpolishing & two nos groove cutting line complete all as specified and directed. |
| 34 | M&L Machine cut kota stone 20-25 mm thick as in riser of steps, skirting, dado etc laid over and including 20 mm thick rendering in CM 1:4laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including rubbing/grinding andpolishingcomplete all as specified and directed. |
| 35 | M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paverblock of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 36 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed. |
| 37 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 38 | M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separatley. |
| 39 | Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 40 | M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed. |
| 41 | M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint complete all as specified and directed. |
| 42 | M&L preparation of old decorated wall surfaces by brooming down or steel wire brushing scraping down smoke spot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying two coat of cement base paint complete all as specified and directed. |
| 43 | S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed. |
| 44 | S&F 4 mm thick frosted / pin headed glass in ventilator shutters complete all as specified and directed. |
| 45 | Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed. |
| 46 | M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 47 | M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 48 | S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 49 | S&F in repairs 25 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 50 | S&F in repairs 32 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 51 | S&F in repairs 40 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 52 | S&F in repairs 50 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 53 | Demolition of brick work in cement motor including pillar etc below / above ground level etc and removing to a distance not ex 50 meter complete all as specified and directed. |
| 54 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar complete all as specified and directed. |
| 55 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed. |
| 56 | Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed. |
| 57 | Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed. |
| 58 | Supply only Rubber / EPDM gasket 4 mm thick complete all as specified and as directed . |
| 59 | Supply, laying and testing in repair for Tubes, \" Medium Grade \" galvanised, 100 mm bore with all fittings; laid in trenches,complete all as specified and as directed . |
| 60 | Supply, laying and testingin repair for Tubes, \" Medium Grade \" galvanised, 80 mm bore with all fittings; laid in trenches,complete all as specified and as directed . |
| 61 | Supply, laying and testingin repair for Tubes, \" Medium Grade \" galvanised, 50 mm bore with all fittings; laid in trenches,complete all as specified and as directed . |
| 62 | Supply, laying and testingin repair for Tubes, \" Medium Grade \" galvanised, 40 mm bore with all fittings; laid in trenches,complete all as specified and as directed . |
| 63 | Supply, laying, jointing & testingin repair for Ductile Iron (DI) Pressure 300mm bore (dia) with Spigot & Socket Ends, Centrifugally Cast (Spun) with Cement Mortar Lining in Inner Side confirming to IS : 8392 /2000 in standard length for classification K-9 and other relevant standards and Metallic Zinc Coating followed by a finishing layer of Epoxy Paint in outer side, suitable for Push-on Joint (Rubber Gasket Joint) in any length and laid in Trenches, complete all as specified and as directed . |
| 64 | Supply, laying, jointing & testing in repair forDuctile Iron (DI) Pressure 200mm bore (dia) with Spigot & Socket Ends, Centrifugally Cast (Spun) with Cement Mortar Lining in Inner Side confirming to IS : 8392 /2000 in standard length for classification K-9 and other relevant standards and Metallic Zinc Coating followed by a finishing layer of Epoxy Paint in outer side, suitable for Push-on Joint (Rubber Gasket Joint) in any length and laid in Trenches, complete all as specified and as directed . |
| 65 | Supply, laying, jointing & testingin repair for Ductile Iron (DI) Pressure 150mm bore (dia) with Spigot & Socket Ends, Centrifugally Cast (Spun) with Cement Mortar Lining in Inner Side confirming to IS : 8392 /2000 in standard length for classification K-9 and other relevant standards and Metallic Zinc Coating followed by a finishing layer of Epoxy Paint in outer side, suitable for Push-on Joint (Rubber Gasket Joint) in any length and laid in Trenches, complete all as specified and as directed . |
| 66 | Supply, laying, jointing & testingin repair for Ductile Iron (DI) Pressure 100mm bore (dia) with Spigot & Socket Ends, Centrifugally Cast (Spun) with Cement Mortar Lining in Inner Side confirming to IS : 8392 /2000 in standard length for classification K-7 and other relevant standards and Metallic Zinc Coating followed by a finishing layer of Epoxy Paint in outer side, suitable for Push-on Joint (Rubber Gasket Joint) in any length and laid in Trenches, complete all as specified and asdirected . |
| 67 | Supply, laying, jointing & testingin repair for Ductile Iron (DI) Pressure 80mm bore (dia) with Spigot & Socket Ends, Centrifugally Cast (Spun) with Cement Mortar Lining in Inner Side confirming to IS : 8392 /2000 in standard length for classification K-7 and other relevant standards and Metallic Zinc Coating followed by a finishing layer of Epoxy Paint in outer side, suitable for Push-on Joint (Rubber Gasket Joint) in any length and laid in Trenches, complete all as specified and as directed . Note- Excavation,DI Specials and rubber gasket joint shall be measured and paid separately complete all as specified and directed. |
| 68 | Supply and fix in repair DI Bends tapers, Tees, pieces (Single or double branch) any Type and angle/ radius and straight connecting pieces for Pipe upto 300mm bore complete all as specified and as directed. |
| 69 | M&L Cast Iron Sluice Valve 80 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve,complete all as specified and as directed . |
| 70 | M&L Cast Iron Sluice Valve 100 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve,complete all as specified and as directed . |
| 71 | M&L Cast Iron Sluice Valve 150 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve,complete all as specified and as directed . |
| 72 | M&L Cast Iron Sluice Valve 200 mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve,complete all as specified and as directed . |
| 73 | M&L Cast Iron Sluice Valve 300mm bore (dia), comply with IS:14846-2000, Class PN-1.6, both Ends Flanged, having Gun Metal Working Parts, Stainless Steel Spindle with Cast Iron Hand Wheel with all necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceable Sluice Valve,complete all as specified and as directed . |
| 74 | Supply and Fixing cast iron body and brass gate heavy duty non return valve ( NRV) 80 mm bore with flanged endall necessary fixing Arrangements such as Gaskets, Mild Steel Nuts, Bolts, Washers, etc. and testing including taking down unserviceablenon return valve ( NRV), complete all as specified and as directed. |
| 75 | M & Lin repair run lead joints for pipes and fittings (spigot and socket ends) 80 mm bore (dia) and testing complete all as specified and asdirected. Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 76 | M & Lin repairrun lead joints for pipes and fittings (spigot and socket ends) 100 mm bore (dia) and testing complete all as specified and asdirected . Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 77 | M & Lin repairrun lead joints for pipes and fittings (spigot and socket ends) 150 mm bore (dia) and testing complete all as specified and asdirected .Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 78 | M & Lin repair run lead joints for pipes and fittings (spigot and socket ends) 200 mm bore (dia) and testing complete all as specified and asdirected .Note- Excavation & earth work if required shall be included in quoted rate complete all as specifed and directed. |
| 79 | M & Lin repairrun lead joints for pipes and fittings (spigot and socket ends) 300 mm bore (dia) and testing complete all as specified and asdirected .Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 80 | M & Lin repairlead wool joints for pipes and fittings (spigot and socket ends) 80 mm bore (dia) and testing complete all as specified and asdirected . Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 81 | M & Lin repair lead wool joints for pipes and fittings (spigot and socket ends) 100 mm bore (dia) and testing complete all as specified and asdirected . Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 82 | M & L in repair lead wool joints for pipes and fittings (spigot and socket ends) 150 mm bore (dia) and testing complete all as specified and asdirected .Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 83 | M & Lin repair lead wool joints for pipes and fittings (spigot and socket ends) 200 mm bore (dia) and testing complete all as specified and asdirected .Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 84 | M & Lin repair lead wool joints for pipes and fittings (spigot and socket ends) 300 mm bore (dia) and testing complete all as specified and asdirected .Note- Excavation & earth work if required shall be included in quoted rate complete all as specified and directed. |
| 85 | M&L Construction Brick Masonry Valve Pit of size 900x900x900 mm (Internal Dimension) one Brick thick Wall in Cement Mortar 1:4 on 100mm thick PCC 1:4:8 (40mm graded aggre-gate) in Foundation, Rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS Sheet Valve Pit Cover, welded with 40x5mm Flat Iron Frame alround including provision of Hinges, Handle with Locking Arrangement and 40x40 x6mm Angle Iron Frame fixed on top of Valve Pit by means of holdfast 150mm long, embedd -ed in PCC 1:2:4 (20mm graded aggregate) Block of size 230x200x100 mm, applying two coats of Anti-corrosive Paint to all exposed Steel Surfaces over a coat of red oxide zinc chrome Primer after preparation of Surfaces and necessary Earth Work in Soft/ Loose Soil including demolition of unserviceable Valve Pit, complete all as specified and asdirected . |
| 86 | M&L Construction Brick Masonry Valve Pit of size 750x750x900 mm (Internal Dimension) one Brick thick Wall in Cement Mortar 1:4 on 100mm thick PCC 1:4:8 (40mm graded aggre-gate) in Foundation, Rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS Sheet Valve Pit Cover, welded with 40x5mm Flat Iron Frame all round including provision of Hinges, Handle with Locking Arrangement and 40x40 x6mm Angle Iron Frame fixed on top of Valve Pit by means of holdfast 150mm long, embedd -ed in PCC 1:2:4 (20mm graded aggregate) Block of size 230x200x100 mm, applying two coats of Anti-corrosive Paint to all exposed Steel Surfaces over a coat of red oxide zinc chrome Primer after preparation of Surfaces and necessary Earth Work in Soft/ Loose Soil including demolition of unserviceable Valve Pit, complete all as specified and asdirected. |
| 87 | M&L Construction Brick Masonry Valve Pit of size 600x600x600 mm (Internal Dimension) one Brick thick Wall in Cement Mortar 1:4 on 100mm thick PCC 1:4:8 (40mm graded aggre-gate) in Foundation, Rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS Sheet Valve Pit Cover, welded with 40x5mm Flat Iron Frame alround including provision of Hinges, Handle with Locking Arrangement and 40x40 x6mm Angle Iron Frame fixed on top of Valve Pit by means of holdfast 150mm long, embedd -ed in PCC 1:2:4 (20mm graded aggregate) Block of size 230x200x100 mm, applying two coats of Anti-corrosive Paint to all exposed Steel Surfaces over a coat of red oxide zinc chrome Primer after preparation of Surfaces and necessary Earth Work in Soft/ Loose Soil including demolition of unserviceable Valve Pit, complete all as specified and asdirected . |
| 88 | M&Lin repair Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of FE-410-W (gde-E-250) for erection of path all around the water tank at 40 to 60 Feet height MS staging complete all as specified and as directed. |
| 89 | M & Lin repair for fabrication of MS clamp of size 50x4 mm and min total length 1.0 mtr using 4 nos nut, bolt and washers for supporting lead joints for CI pipes complete all as specified and as directed. |
| 90 | Supply, laying and testingin repair for Tubes, \" Medium Grade \" galvanised, 25 mm bore with all fittings; laid in trenches,complete all as specified and as directed . |
| 91 | Supply, laying and testingin repair for Tubes, \" Medium Grade \" galvanised, 20 mm bore with all fittings; laid in trenches,complete all as specified and as directed . |
| 92 | S & F in repair150 mm DI adjustable mechanical joint complete all as specified and directed . |
| 93 | S & F in repair 100 mm DI adjustable mechanical joint complete all as specified and directed . |
| 94 | S & F in repair 80 mmDI adjustable mechanical joint complete all as specified and directed . |
| 95 | S & F in repair 200 mmDI adjustable mechanical joint complete all as specified and directed . |
| 96 | S & F in repair 300 mmDI adjustable mechanical joint complete all as specified and directed . |
| 97 | M&L for painting of various colouredCI/GI/Column pipe line in sidepump house of size 4\"to 12\" with two coats of syentheic enamel paint after removing/ scratching old painted surface incl preparation of surface and providing one coat of primer completeall as specified and directed. |
| 98 | Supply, lowering, installation, testing and commissioning of submersible pump & set in replacement complete with 3 phase submersible electric motor coupled with the pump having capacity 11 KW/15 HP , 7 stage or as per OEM recommended stage suitable for coloum pipe/ outlet pipe of 80mm dia fixing with existing coloumn pipe at site complete all as specified and as directed. Note: Old U/s Pump shall be deposited to MES Store. |
| 99 | Supply, lowering, installation, testing and commissioning of submersible pump & set in replacement complete with 3 phase submersible electric motor coupled with the pump having capacity 7.5 KW/10 HP , 4 stage or as per OEM recommended stage suitable for coloum pipe/ outlet pipe of 80mm dia fixing with existing coloumn pipe at sitecomplete all as specified and as directed. Note: Old U/s Pump shall be deposited to MES Store. |
| 100 | M&L for dismentaling existing burnt elect openwell submersible pump set complete of any make/capacity from existing position, cutting complete burnt winding removing carefully, rewinding complete stater with water proof copper wire of existing and suitable gauge, paper insulation, sleeves etc, servicing/ greasding filling of cavities, grinding, machining of shaft, impiller,replace gun metal bushes beraing of existing size of pump and inclung refixing of 15 HP complete all as specified and directed. |
| 101 | All as per Item No 99but 10 HP Capacity and ditto. |
| 102 | All as per Item No 99 but 7.5 HP Capacity and ditto. |
| 103 | S&F rubber star packing of motor & pumpof existing size and type including resetting alignment of the pump sets of 60 HP capacity complete all as specified and directed. |
| 104 | All as per Item No 102 but 25 HP pump. |
| 105 | All as per Item No 102 but 15 HP pump. |
| 106 | S&Fin replacment ofPressure gauge 0-150LBS/in2 / 0 to 10 KG/cm2 ISI marked complete all as specified and directed. |
| 107 | S&Fin replacment ofPressure gauge0 to 70 LBS/in2/ 0-1000 KG/cm2ISI marked complete all as specified and directed. |
| 108 | S&F in repairs 80 mm bore & 3 m long MS heavy duty seamless black column pipe with both ends flanged, wall thickness not less than 5.4 mm in borewell with and including all jointing materials such as nut, bolts, washers, rubber gasket etc. complete all as specified and directed. |
| 109 | (a)Disconnecting the power cables from the control panel, lifting the submersible pump set along with the GI tubing 50/80 mm carefully from the bore well without damaging the existing MS casing pipes using bore well ringfrom various sites and unscrewing each length/section of pipe complete all as directed by Engr-in-Charge. (b) Disconnecting submersible pump set and taken to work shop for repair/servicing and bringing back after repair. (c)Cleaning the GI pipes that have been remove, both internally and externally keeping serviceable pipes ready for installation. (d) Dismantling strainer, replacement of defective filters and re-assembling the same complete.(e)Jointing the submersible cable with M-Seal in water proofing condition all as directed by Eingr-in-Charge. Contd..../- |
| 110 | (f)Flushing the borewell at any depth with compressed air of compression capacity 300 PSI 100 CFM driven by diseal Engine and back washing continuously for not less than 02 hours or until clear water is flushed out and pure water is received complete all as directed by Engr-in-Charge.(g) Re-installing the submersible pump set alongwith the power control cable lowering into the existing bore well casing using bore well rig after jointing each length of the GI pipes step by step to the entire length and locking the system connecting with the external water supply lines and power controls and testing and commissioning at site to the entire satisfaction all as directed by Engr-in-Charge. Note for serial item No 1(a) to (g): - Repair and servicing of submersible pump set, rewinding of motor, electric cable and GI tubing shall be measured separately under relevant items of Schedule \"A\". |
| 111 | Supply and fix submersible cable 3 core 6 sqmm multi stranded copper conductor in replacement of unserviceable existing cable.Make - Finolex,/Polycab/Plaza. |
| 112 | Supply and fixing mild steel holding down clamps(set of two) made outfrom 100mm wide, 10mm thick flat iron and length 1.5 meters bend in shape as specified fixed with 4 set of nut, bolt and washer for holding 50mm dia housing pipe fixed in position complete all as specified and directed. |
| 113 | Supply and fixing mild steel cap of 5.4 mm wall thickness with internal threads and locking arrangement suitable for housing pipe of 200 mm dia fixed in position complete all as specified and directed. |
